Microphone button

Similar Questions

• in the photo story 3 on vista, the Configuration of the microphone button does not work. Any suggestions?

  I can't rcord through my microphone but cannot get the microphone to configure to open. I just get a line dotted around the button. I need to increase the volume of the audio narration and this is supposed to be the way to do it.

  Hi Trevir,

  '

  You may need to use the program in Vista Compatibiltiy mode. Read the following article.

  Make older programs in this version of Windows

• Button mute Microphone of Lenovo X 220

  I recently had to reimage my laptop with Win7 Pro 64-bit. I installed all the drivers listed, but still somehow my microphone mute button does not work. It lights up for a second at the start, but after that it will not repsond. Any suggestions?

  Well I did some more research and found this article which helped me, if you have all these parts work to the right of the microphone button does not work.

  http://forums.Lenovo.com/T5/X-series-ThinkPad-Laptops/X220-hotkeys-not-working-since-system-update/t...

  My problem is solved thanks me!

• Re: Microphone completely after installing XP on Satellite Pro P300

  My father bought a Satellite Pro P300 that I went down to Windows XP by using the included CD/DVD.
  Later, we found that the internal microphone is very quiet when we tried to use it.
  We need to yell into the microphone to get any sound at all, more like sounds random blip. Type the microphone sounds more scratch.

  All other sound effects are great. speakers work fine. We connected an external microphone to the mine in the laptop and video calls worked without problem, the problem is only with the internal mic.
  I saw that someone else has the same problem in the forum (link: [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=33844&tstart=0]), but it does not say how or if this problem has been resolved.

  I would really appreciate if someone could give me the fix or a link to the fix to our problem other than plug in an external microphone.

  Hello

  Windows XP supports a microphone amplifier. Have you enabled it?

  Go to control panel-> Audio & Sound Devices-> advance tab press Volume button

  Optionally, select advanced controls

  Then you should see the volume of the microphone. Please set it to a higher value.
  In addition, press the advanced under the microphone button.

  Here, you can mark the micro amp.

  Concerning

• my microphone does not work it is on, but he can't hear anything...

  my microphone does not work it is on, but it means nothing...? is there a mute on a microphone button.

  Hi Mike,.

  1. What is the number of brand and model of your computer?

  2 are you able to get the speaers sound?

  3. were you able to use the microphone before without any problem?

  4. did you of recent changes on the system?

  Method 2: Set the Microphone as default.

  Once the drivers installed check if the microphone is set by default.

  Exercise the functions mentioned below to adjust the Microphone as default:

  a. click Start and then click Panel.

  b. click on her, then a new window will open.

  c. click the Read tab, right click on Microphone and click on turn on.

  d. If you see the Microphone in the list, right-click on the white space and select see the disabled devices.

  e. then you would see the Microphone. However, if you do not see the checkmark on it, right click on it and click on turn on.

  f. also point out that Microphone and click on ""as a default " "

   

  Method 2:

  You can visit the computer manufacturer and try to install the latest version of the sound drivers and check.

  Update drivers: recommended links

• How the message to your Favorites

  How to set my watch to be able to text my favorites more quickly

  Hello

  Under watch OS 3, to send a new message using your Apple Watch Messages:

  • Use Siri: for example "Hey Siri, say Jane I'll be there in 30 minutes" and then lower your wrist to send (No button tap / press is necessary).
  • Open your Messages > firmly press the list of conversations > tap new Message > tap Add a Contact, then either:
    • Tap a contact in the list of recent conversations that appears;
    • Or tap on '+' to select your complete contacts list;
    • Or press the Microphone button to search for a person in your contacts or dictate a phone number.

  More information:

  https://help.Apple.com/watch/#/apd92a90f882

• SIRI remote no longer meets its

  When I first set up my TY Apple (4th Gen) the SIRI remote worked perfectly, I don't know when exactly it has stopped working, but now if I press the Microphone button, the TV responds and shows the bar of SIRI, but it not modulated and continues to give me any suggestions of what to say.

  Before you answer it please as I know how it is supposed to work (the key while talking) and I made no changes before setting it has stopped working.

  An old post where a person could not get SIRI to work when it was set up, said the solution was to use the HDMI to HDMI Cable, I have always used a HDMI cable to HDMI.

  What I tried:

  1. taking the floor after the key; in the event that an update has changed the way it worked (wish that was the case also)

  2 rebooted, reset in the menu and pulled to reset Apple TV

  3 non-matched the remote and re-paired.

  4. actually #1: I checked all options that all posts related to the "SIRI works do not", said to check. SIRI located on, correct language, correct area...

  Firmware remotely: 0 x 0245

  Apple TV

  MDL: A1625 (64 GB)

  tvOS: 9.2.1 (13Y772)

  It seems that this can happen if the zoom is enabled in accessibility options.

• Sony Bravia 4 K Ultra HD model XBR-43X830C & remote control RCC-TX100U - don't pair / work! Help!

  I bought (via Internet) remote control Sony RMF-TX100U touch pad to pair upward with my Ultra model HD Bravia Sony 4K 43 '' TV XBR-43X830C, since the remote control of the touchpad does not come with this TV in particular. I followed all THE procedures of paved remote reset touch that is to remove the batteries, batteries, hold down the respective buttons and receive the flashing red light (twice) on the remote control, I did. Also, I did reset the TV rather than unplugging it. On television, I went to settings, remote and followed the onscreen but which are basically press and hold the Volume - button and then press the "microphone" button while continuing to hold down the key, - Volume for three seconds, remote pointed at the IR receiver TV. I did it over and over again and nothing happens! I find NO Google search solutions to this problem. Can anyone advise of alternatives to get this remote touchpad to play nice with my Sony TV? I'm assuming that this remote is COMPATIBLE with this particular set? Some say yes, some say no. Please advise. Any help will be greatly appreciated. Thank you in advance!

  Doc technical marketing for your TV on the Sony site.

  https://docs.Sony.com/release//specs/XBR43X830C_mksp.PDF

  Shows:

  Optional accessories

  Remote control Touchpad (RCC-TX100U)

  Cable MHL (DLC-MC20)

  Subwoofer (SWFBR100) wireless

  4 K Media Player (FMP - X 10 (for the USA. only))

  Should work.

  Try to make a power-pull reboot... turn TV off, draw power for a minute, plug in and restart.

  Put different batteries in the remote control.

  Try again.

  If it doesn't work, distance could be faulty.

• Need help! Required before Tuesday, March 8, 2016

  Cannot add audio YouTube to iMovie for iPad 2 iOS 9.2.1 Air without using the microphone button. Help!

  Assistance required BY Tuesday, March 8, 2016

  I mean Monday, March 7, 2016

• Cannot enter numbers in the phone when you use Skype-to-go

  When I use Skype-to-go I can't enter the numbers after answering the call. Then when I cal a answering machine from a call center I can't be connected. Please tell me if what is happening to others? How can it be resolved? For me, is a huge problem

  I googled this and got an answer that worked! In the call to the window that is displayed when you are on a call, click the button on the keyboard (the one to the right of the microphone button) and a keyboard will appear. It worked perfectly enter # and numbers on my call.

• How to trigger the dictation from the smart keyboard on the iPad pro.

  I use dictated on my iPhone and my iPad quite often.

  However on my new iPad Pro with the smart keyboard attached, I do not how to trigger the dictation from the keyboard.

  I don't see how to get the soft keyboard back to press the button of the microphone are there, such space suggested by some on this forum.

  This doesn't seem to work in the latest iOS Update 9.

  I would be fine with a hotkey, or have to invoke the keyboard of the shop, then press the button of the microphone, but I don't see how do either.

  When the Emoji button on the keyboard smart strike as the keyboard, the software keyboard emoji is displayed, the space but when I press the soft ABC capital but I cannot get to the regular keyboard with the microphone button.

  A possible alternative would be to use Siri to dictation trigger in recording a memo or another application, space but I didn't understand how to do this job either.

  Has anyone experience this problem and found a solution?

  Unfortunately I had to spend a good hour on the phone with technical support when they finally admit that it was an oversight by Apple.  I hope someone reads this post until they spend countless hours trying to understand something, but has no solution at the moment. Frustrated!

• How to audio notes 1Dx image?

  I have a Canon 1Dx and I heard there is a way to put audio notes on a picture. I have not been able to see that and was looking for some assistance.

  I figured out how to use: you just hold the blue microphone button down (@3-4 seconds) until it appears a screen audio and thénot just follow the guests. He practices a couple of times before going out. It kicks butt!

• Speech recognition does not recognize dictated.

  Recognization of speech is dictated not recognized as dictation, includes only orders. It is a novelty because when I started using it it worked fine. The microphone is very good because he always hears commands and responds correctly. Any ideas? Please, I beg you.

  Hi Mlee,

  Control Panel-> speech-> speech options Advance open pick and choose the language (English in the United States). Try the word by far.

  There are several ways to correct mistakes made during dictation. You can say "correct that" to correct the last thing you said. To correct a single word, say "correct" followed by the word that you want to correct. If the word appears several times, all instances are highlighted and you can choose the one you want to correct. You can also add words that are often misunderstood or not recognized by using the speech dictionary.

  To use the alternates Panel dialog box

  1. Click to open Windows speech recognition.

  2. Say "start listening" or click the Microphone button to start the listening mode.

  3. Do one of the following:

     • To correct the last thing you said, say "correct that."

     • To correct a single word, say "correct" followed by the word that you want to correct.

  4. In the Group of alternates dialog box, say the number next to the item you want, and then on "OK".

     Note

     • To change a selection, in the Group of alternates dialog box, say "Spell" followed by the number of the item you want to change, click 'OK '.

  Use the speech dictionary

  1. Click to open Windows speech recognition.

  2. Say "start listening" or click the Microphone button to start the listening mode.

  3. Say "open Speech Dictionary."

  4. Do one of the following:

     • To add a Word to the dictionary, click or say add a new Word, and then follow the instructions in the wizard.

     • To prevent a specific word of dictation, click or say prevent a Word from dictation and then follow the instructions in the wizard.

     • To correct or delete a word that is already in the dictionary, click or say change existing words, and then follow the instructions in the wizard.

       A speech profile has not been created. You can train your computer to better understand you by creating a voice profile that your computer uses to recognize voice commands.

       To create a voice profile

       1. Click to open speech recognition.

       2. Click Train your computer to better understand you, and then follow the instructions

          Thankzzzzz

• Micro system

  I turned off my computers microphone.  to save other empty titles to use as breaks in the media player. I can't find where to turn them back on.

  Thank you
  Steven V

  Hi Steve,.

  Thanks for choosing Microsoft Community.

  According to the description, it seems that you are having problems with microphone start-up. I will certainly help you fix this problem.

  I suggest that you follow the steps in order to test, check the connections and hardware, update the audio drivers and configure the audio settings of Windows.

  Step 1: Test of an audio signal

  1. Click on Start, then Control Panel.
  2. Click hardware and soundand then click manage audio devices...
  3. Click the recording tab.
  4. To test the microphone, speak into it. To test the line, send a signal to the line at the port of devices audio source (press play on the audio player). Look at the gray bars next to the name of the device under the recording tab:
     • If the gray bars next to the device name turns green, this device is active and an audio signal is passed through the microphone or line-in port. This step shows that this problem is related to sound parameters in the software that uses the microphone. If you have not already done so, set the device selected by default and adjust levels. Once the device is set by default and levels are defined, use and adjust the sound recording or voice carrying software.
     • If the gray bars remain inactive and grey, the device does not have a signal. Leave the record open tab and go to the next step.

  Step 2: Check the volume levels and mute

  The volume of the speaker to the microphone and line - in may be activated or rejected. Use the following steps to check the volume of speaker for line and microphone levels.

  1. Click Startand then click Control Panel.
  2. Click hardware and sound.
  3. Click sound.
  4. Select speakersand then click Properties.
  5. Click the levels tab.
  6. Click on any line that is cut and Muted next to Microphone button.
  7. Use the slider to increase the micro level and each line at least 75.
  8. Click OK.

  Step 3: Configuring the settings of Windows registry

  By default, Windows Vista automatically activates microphones and line-in ports. Use the following steps to set the microphone/line-in port to be the default port and configure the logging levels.

  1. If the recording in the Audio window tab is not selected, open the sound and click therecording tab and make sure the State is defined as below.

  1 - port microphone - work and set as default

  2 - line In - work

  3. digital (S/PDIF port) In - work

  4 - stereo Mix (mixer software) - disabled

  1. If several microphones or line - in ports are available, select the port you want to use. Clickset as default to make this device default audio input device.
  2. If the device you want to use contains a small circle with an arrow pointing down, the device is disabled. To activate the device, right click on the device name and selectActivate.
  3. With the selected device, click Properties, and then click thelevels tab.
  4. Adjust the slider until 75% of its range.
  5. If the mute is enabled, click the button mute to reactivate the device. The mute button should show as a blue speaker without any red circle.
  6. If the Microphone Boost is available, adjust to dB + 20.0.
  7. Click OK to make the changes.
  8. Test the microphone as was done in step 1 to determine if Windows is able to detect a signal from the microphone or line used. If you have completed all the steps and the microphone or the source device still does not work, the audio ports or the computer's sound hardware can be bad.

  You can also check the KB Article link for reference:

  Tips for solving common audio problems:
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.

• How to enable the microphe on?

  I want to keep the karaoke of microphe?

  Hello

  You receive an error message when you try to connect the microphone?

  Follow these steps and check.

   

  Test for an audio signal

  a. click on Start, then Control Panel.

  1. Click hardware and soundand then click manage audio devices...
  2. Click the recording tab.
  3. To test the microphone, speak into it. To test the line, send a signal to the line at the port of devices audio source (press play on the audio player). Look at the gray bars next to the name of the device under the recording tab:

  o If the gray bars next to the device name turns green, this device is active and an audio signal is passed through port microphone or line-in. This step shows that this problem is related to sound parameters in the software that uses the microphone. If you have not already done so, set the device selected by default and adjust levels. Once the device is set by default and levels are defined, use and adjust the sound recording or voice carrying software.

  o If the bars grey remains grey and inactive, the device does not recognize a signal. Leave the record open tab and go to the next step.

   

  Now, to check the levels of volume and mute

  The volume of the speaker to the microphone and line - in may be activated or rejected. Use the following steps to check the volume of speaker for line and microphone levels.

  a. click Startand then click Control Panel.

  1. Click hardware and sound.
  2. Click sound.
  3. Select speakersand then click Properties.
  4. Click the levels tab.
  5. Click on any line that is cut and Muted next to Microphone button.
  6. Use the slider to increase the micro level and each line at least 75.
  7. Click OK.

  Connect one microphone, music player or other audio device to your computer

  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-a-microphone-music-player-or-other-audio-device-to-your-computer

   

  Thank you