Mini-GBIC/SFP and VLAN
I'll buy two switches Cisco SG200 - 26 with a TRANSCEIVER MGBSX1 for each and connect with each other via fibers. Am I right to assume that the fiber port is configurable for VLAN? So if I set up four VLANS (1-4 on two switches, port 1 in VLAN1, VLAN2 2 port, etc.), I can configure the fiber port to be on all four VLANS so that traffic for all four VLAN moves between the two switches?
Hi David, you're right.
-Tom
Please mark replied messages useful
Tags: Cisco Support
Similar Questions
-
Gigabit Ethernet SX Mini-GBIC SFP Cisco transceiver
This reference Cisco: Cisco MGBSX1
Any type of connector can support?
And how can I change the type of connector of LC to SC?
Ho Yousovich, all GBIC SB is LC.
http://www.Cisco.com/c/en/us/support/docs/interfaces-modules/CWDM-GBIC-s...
-
Using mini gbic to stack 2 of SGE2010
Hello
Is there a major advantage to use the GBIC ports to superimpose on the regular ports of GB (24 and 48, I think?) in terms of performance, stability, etc.?
Thank you
Neil
Hi Neil,
So to answer the question quite simply, there is no additional benefit using mini GBIC (SFP) compared to a CAT6 cable to connect the switches in a stack. Copper fittings or fiberglass can be synced to 1000 Mb/s.
The only advantage of the use of mini-GBIC SFP or; s if the connection between the switches are more than 100 meters, or 328 feet.
But I'm more happy to connect switches with CAT6 cables for cumulation purposes, is it more cost-effective.
Best regards, Dave
-
Hello
I want to know who can be used mini-GBIC works with the switch SGE2000. Also 10/100-mini-Gbic work for?
Best regards
Linksys 100 M SFP switch Support and software output Minimum requirements Table
For SR SRW, EMS, EMS and switches SLMSwitching products
MFEBX1
MGBBX1
MGBLH1
MGBLX1
MGBSX1
MGBT1
MFELX1-100 FPS
MFELX1-100 FPS
Comments (MFELX1 & MFELX1)
SR2024
N/A
N/A
Auto
N/A
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SR224G
N/A
N/A
Auto
N/A
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SRW208G
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.3
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW208L
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.3
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW208P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.3
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW208MP
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.2
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW2008
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.2
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW2008P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.2
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW2008MP
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.2
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW224G4 (v1.0/v1.1)
Auto
Auto
Auto
Auto
Auto
Auto
Minimum firmware 1.2.2
Minimum firmware 1.2.2
Manual installation for 100M SFP
(Click here for Instructions)SRW248G4 (v1.0/v1.1)
Auto
Auto
Auto
Auto
Auto
Auto
Minimum firmware 1.2.2
Minimum firmware 1.2.2
Manual installation for 100M SFP
(Click here for Instructions)SRW224G4P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Automatic 100 M SFP
SRW248G4P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Automatic 100 M SFP
SRW2024P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.3
Minimum Firmware 1.0.3
Automatic 100 M SFP
SRW2016
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SRW2024
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SRW2048
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SRW224P
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SFE2000
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SFE2000P
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SGE2000
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SGE2000P
Auto
Auto
Auto
Auto
Auto
Auto
SUPPORT NO
SUPPORT NO
Plan No. material Limitation in support
SLM224G2
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.2
Minimum Firmware 1.0.2
Manual installation for 100M SFP
SLM224G
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM248G
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM224P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM248P
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM2024
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM2048
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM224G4S
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
SLM248G4S
Auto
Auto
Auto
Auto
Auto
Auto
Minimum Firmware 1.0.1
Minimum Firmware 1.0.1
Manual installation for 100M SFP
A list of supported for your switch GBIC is attached.
-
I have a mini ipad 2 and I fight a smart box and it is not turning off the ipad.
I have a mini ipad 2 and I fight a smart box and it is not turning off the ipad.
Go to settings > general, and then turn on lock/unlock.
-
I have a HP mini 110-3130 and locked the touchpad.
I have a HP mini 110-3130 and locked the touchpad. A small icon with a line through it. Once this icon fades the touchpad mouse stops working. Suggestions for addressing anomaly welcomed. There is no light or switch around the touchpad unlike some models
Hello
Try double-clicking top left corner of the touchpad - is often the method to turn the touchpad on or off.
Kind regards
DP - K
-
can someone give me links to download only setup.exe and autorun.exe to the tribes of heroes 5 of the game is that mine are corrupted and I can't download the whole game again?
This is the incorrect forum for your question.
Try using Bing or Google, like this
http://www.bing.com/search?q=Heroes+5+tribes+of+the+East&form=OSDSRC
-
Any REFLEX Cannon is 29 min video stop and don't work with cards sdxc fornat Exfat No 4 GB
Any REFLEX Cannon is 29 min video stop and don't work with cards sdxc fornat Exfat no limit 4 GB?
For the VIDEO?
Thank you
Almost all of the Canon 'Vixia' line of cams are less than 1 k $. The Vixia HF G30 $1150 and it is the only model over $1 k. Here are all the models to consumer prices. (X XAnn, XFnnn, & XCnn series is top of the line, and of course the EOS film bodies are much more expensive.)
As far as I know, they all supports SDXC cards.
-
Reference Dell SFP and SFP + transmitters suggested M8024-K
Which are issuers recommended Dell SFP and SFP + for the M8024-K blade pass?
In particular, I would like to know the numbers for the following:
1 integrated SFP
1.1 10GbE SFP + SR
1.2 FPS 1GbE
1.3 FPS 1GbE RJ45
2 10GbE SFP + plug-in
2.1 FPS + 10GbE SR
Your help is appreciated.
Here are the part numbers, that I have just listed. SFP transceivers are supported only in the fixed ports and will not work in the FlexIO module.
10GbE SFP + SR = RK0CX
SFP - 1 G - SX = 63GGJ
SFP - 1 G - LX = VYW04
SFP RJ45 1GbE = PF911 -
Good afternoon!
I'm looking to implement a 5548 in our existing infrastructure. I want to preface this by saying that I am very new to networking.
I'm looking to have at least two VLANS separated.
-The first vlan for public sites face. These will have static public IP addresses.
-The second VLAN is iSCSI traffic. I would like that it won't face public.
Is it possible to Setup or should I be looking for a different solution.
If possible, how should I go about setting up?
Thank you!
The port that connects to your router should be placed in Trunk mode with the VLAN you want in the trunk port. All ports are in VLAN1 access mode by default, this means that the port that plugs into your routing device is in access mode for VLAN 1 and VLAN 1 has internet access. For traffic VLAN 2 to access routing equipment that you will need to change cela port in Trunk mode and adds 2 VLAN as a VLAN Tag.
468-page guide details where to put labeling.
See you soon
-
Interconnection SFP SFP + and XENPAK / X 2
Is it possible to connect:
- SFP + and XENPAK / X 2, for example 10 G-FPS-SR (Cat2960X or Cat3560X) and XENPAK - 10 GB - SR (Cat6500) or X 2-10 GB-SR (Cat3750E)?
- SFP + and SFP, SFP - 10 G - SR (Cat2960X or Cat3560X) e.g. and GLC-SX-MM (Cat6500 or Cat3750G/E)?
- GLC-SX-MM or GLC-LH-SM will work in SFP + (Cat2960X or Cat3560X) slots?
announcement 1 - I don't want to wiring, I ask to know if these two modules "would see" between them (link)
AD 2 - it seems that SFP - 10 G - SR cannot "downgrade" itself to 1 Gbps speed.
Ad 3 - modules of 1 Gbit/s will work into the SFP slots +?
You can not.
As I have noted, "the G - SR SFP - 10 is 10 Gbps only."
It runs at 10 Gbps throughput of liaison and no other speed.
-
Hi all
I was hired on with a State... Now its been awhile, but I do not remember how subinterfaces and VLAN all link together!
Now correct me where I'm wrong (please), but them VLAN is created on the correct first switches? When you create a VLAN on a switch you don't need ip or gateway address by default because them VLANS are the switch. If you want intervlan routing you need a router. Then, you configure a port trunking between the switch and router (ISL, 802. 1 q). Now in the router, you can create a VLAN, and here you inter the ip subnet or the default gateway addresses correct? This is where I get confused as to what reasons do you need subinterfaces? How they roped VLAN and what would be the logical flow of data?
Anyhelp would be appreciated!
Yes you are right. If you are using the layer 2 switch and want to make the intervlan Routing then you need Layer 3 router device. But you must configure the interfaces sub with the default gateway to route traffic. Because there is a single trunk between swich and router so we need sup interfaces for multiple VLANs.
Interface FastEthernet0/0.1
Encapsulation dot1q 10 (10 represent 10 ID VLAN)
10.1.1.1 IP address 255.255.255.0
If you use a layer 3 switch, then you point all sub interfaces need so then you can create the interface vlan with the default gateway. You must enable ip Routing.
Interface vlan 10
10.1.1.1 IP address 255.255.255.0
Hope this will help.
Please rate if this can help.
Thank you
-
We have a site divided into 2 IEE802.1Q VLAN, using no switches Cisco. They have a PIX515 for Internet access. It is also configured to provide inbound VPN access for management and general purpose of access.
In principle it is possible to set up a new VPN connection which is reflected by its interior traffic be tagged with a specific VLAN ID while all other traffic (including other VPN connections) remain without a label?
If the PIX ends your VPN from the outside that the answer is no. If the VPN is coming from outside, and ending at the PIX she never travels a VLAN. VLAN tagging is used to identify what VLAN came from a source image and what VLAN it is intended for a current switch vlan can 'route' frame through the appropriate VIRTUAL LAN. Why you want to tag from outside VPN traffic? If it's to control access, you can specify 2 VLANS and VLAN 3 on the PIX (as long as it has code 6.3) and control what VLAN, you want that each group VPN access to through the use of the ACL. Each VLAN on a PIX is treated as a physical interface. It has its own security prefs (0-100) and can have ACL applied to them as well as the physical interfaces.
-
Create 2 VLAN (VLAN 1 and VLAN 2)
Hi all
I need help and advice with my new Cisco SF300-48. I want to create 2 vlan (vlan 1 and vlan 2). The switch is set at layer 2.
example:
VLAN 1 (port 1, 2, 3), vlan 2 (port 4, 5, 6)
VLAN 1 can communicate with each other (port 1, 2, 3) and vlan 2 can communicate with each other (port 4, 5, 6)
But vlan 1 cannot communicate with vlan 2.
Any help would be appreciated
Thank you
Johan
Well, as far as I understand the message communication between the VLAN is not necessary. The thing is, that all ports LAN VIRTUAL (for example VLAN 1 with ports 1, 2, and 3) cannot communicate with each other. Did you check the configuration of the port / VLAN (VLAN configured to each port configuration right / right about the tag-no identified)?
-
Management and Vlan native in different subnet?
Can I have a management ip and vlan native in a different on AIR-1242 switch subnet and 2960?
Native on switch = 1.
The interface vlan 100 = 10.10.1.25X 24
BVI ip to the vlan 100 = 10.10.1.25X 24
-HM-
Hello
As far as I know, the management and the native will be the same... I guess... You have Vlan native as 1 on the switch and Int Vlan 100 on routing switch? Am I wrong? Let me know what are your needs... which will help me to help out you!
for your question...
Normally, we specify him vlan native on the switch and the AP so that communication happens... communication won't happen if there is a match of...
Looking forward to hear from you!
Let me know if that answers your question...
Concerning
Surendra
====
Please do not forget to note positions that answered your question and mark as answer or was useful
Maybe you are looking for
-
Palm TX will not update (update of business security)
Hi everyone, I need help with my palm tx, it will not update, thanks to WyreNut, I download, but I can get the program to start, the page of the map is empty, I can see it, used on the page info card space, I think that the program is there but will
-
Adjusting the Touchpad - what a Drag
Hello. I use the keys touch for a long time, and I've never had one that works this way. In the middle of work on one screen, my fingers mes doigts inadvertently drag to another screen, every time. How can I disable this feature? (And why would anyon
-
Can I create a distribution group with other than microsoft email accounts?
I want to be able to communicate with a set of independent consultants and match them with each other as a group. I tried to create a distribution group, but I am not able to add addresses of e-mail for the domain package. Anyway I can do this? I tha
-
Where can I download windows xp family?
Hi, where can I download windows xp family? I have a laptop fujitsu siemens witch I have fromated. There the sticker windows with the key for the windows down home but I don't have the windows installation cd. What should I do? Please advice.
-
unknow warning... Help
why it shows this warning sign in the notification bar?