Mix HD Sas and Sata on the T410 with controller Perc H700 [CF]

Similar Questions

• Disks hard SAS and SATA in mixture with controller H730 R730

  I try to set up a new server for our SMEs and wanted to know if I could use say hard 2 SAS drives in raid 1 configuration for hyper-v (r2 2012) host then use 6-2 TB of SATA drives in pass-through mode for use with storage for 2 VMs.

  Bobc007,

  The rule with the help of SAS and SATA drives is that you CAN mix the two in the same controller. You not CAN NOT mix SAS and SATA in the same virtual disks well. The configuration you are looking for is a supported configuration.

  Let me know if this helps answer your questions.

• Mix of Java and C on the same server of 12.5 Tuxedo?

  I run an application big Tuxedo who perform a mix of Cobol and C calling each other in the same service.

  Is it possible that I have will convert the Cobol in Java code, so I'll have a mix of C and Java on the same single server?

  Or does the Java Tuxedo should only include Java in a single server

  Hello

  Within the server Java Tuxedo (TMJAVASVR) that the Java code is supported.  If a single server can support native languages as C and COBOL or Java, but not the two together in a single server.

  Kind regards

  Todd little

  Chief Architect of Oracle Tuxedo

  PS there is no 12.5 Tuxedo don't release 12.1.1, alone and 12.1.3.

• installed my windows 7 Home Premium on a new hard drive, but it says my key is invalid. I bought this copy of the microsoft store and have retained the email with the key.

  installed my windows 7 Home Premium on a new hard drive, but it says my key is invalid. I bought this copy of the microsoft store and have retained the email with the key.

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the report produced by the MGADiag (download and save to the desktop - http://go.microsoft.com/fwlink/?linkid=52012 ) tool
  Once saved, run the tool.
  Click on the button continue, which will produce the report.
  To copy the report in your response, click the button copy in the tool (ignore the error at this stage), and then paste (using r-click and paste or Ctrl + V) in your response.
  -* in your own thread *, please

  What is an upgrade?

  If so, you must install and activate a qualifying operating system before you perform the upgrade.

  For which version and edition of Windows the computer is allowed according to the COA sticker on the case?

• I received a message on my email that my live hotmail is about to be eliminated, and information is required and click on the back with my information. True or phishing?

  I received a message on my email that my live hotmail is about to be eliminated, and information is required and click on the back with my information.  True or phishing?

  Hello

  This is a phishing scam.

  Don

• Gives an error message 213:19 and said that the problem with the license of the product. Yesterday downloaded Muse (30-day trial period). Yesterday, he worked

  Gives an error message 213:19 and said that the problem with the license of the product. Yesterday downloaded Muse (30-day trial period). Yesterday, he worked

  No one can tell you anything without the proper system or other technical details info. Licenses of inevitable Muse is related to CC, in order to check in a first time:

  Log, activation, or connection errors. CS5.5 and later versions

  Mylenium

• My Windows 7 Professional Office system disk has been corrupted and I took the opportunity to install a SSD for a new system disk and reinstall Windows.  The system is installed and running on the SSD, with my old drive system currently used for storage a

  My Windows 7 Professional Office system disk has been corrupted and I took the opportunity to install a SSD for a new system disk and reinstall Windows.  The system is in place and running on the SSD, with my old drive system now used for storage as it is still readable.  The only product Adobe, that I reinstalled so far is drive XI but I would like to reinstall items 8 and Acrobat 9 without occupying more licenses that both are also installed on my laptop.  Can you tell me the best way to do it?  -Thank you

  If you have two activations allocated already and one was lost on the hard drive that has failed, then you must contact the Adobe Support via chat and ask them to reset your activations.

  To the link below, click on the still need help? the option in the blue box below and choose the option to chat...

  Serial number and activation support (non - CC) chat
  http://helpx.Adobe.com/x-productkb/global/Service1.html ( http://adobe.ly/1aYjbSC )

• How to get all the style of paragraphs and their policies of an indesign file and write all the info with info para in a txt file with scripts

  @

  How to get everyone how to get all the style of paragraphs and their policies of an indesign file and write all the info with info para in a txt file with scriptingstyle and their policies of an indesign file and write all the info with info para in a txt file with scripts

  Hello

  Try this,

  var doc = app.activeDocument,
      pstyles = doc.allParagraphStyles,
      report = "";
  for(var i =0;i
  Kind regards
  Cognet
  		   

• How to create the new catalog, categories and products within the ACC with the CCI

  Hi all
  
  I'm new to atg, I just want to create a new catalog, categories and products within the ACC with a BCC (publishing server) and then I have to browse through my jsp application.for added this requirement what configuration I need to do with VAC. Please help me on this ASAP.
  
  Kind regards
  Jyothi.MJ

  There is nothing you need to do for this.
  Go to ACC and create a catalog.

  In the JSP using droplets CategoryLookUp get the properties of the category and its products of the child to display.

  Peace
  Shaik

• Justify the Divs to the left and right of the page with the gaps between the two. Possible?

  I have 4 eponymous divs with different images and rollover Javascript on them, spread horizontally on my page effects.

  I'm trying to align their so there are gaps between each div, but NO space on the right and left side, so that they are tight to the edge. If I put a margin on the right side of 5px, for example, the div right hand still has a gap of 5px, otherwise he's going on the next line.

  Of course, I can make a new rule for the div of the right hand with no margin to the right, but this will make more complex Javascript code with perform effect hover on two types of divs.

  Is it possible to pin the divs to the left and right of the page with an 'auto' margins inbetween them?

  

  I found a solution in any case. I've adjusted to the width of the div so that they coincide closely each side. Then align the images (HTML) 'Left, middle, Hugo, right' so that they are tight against each side and have differences even between them. If all goes well, there is no flaws with this method, it seems to work pretty well.

• You can mix SAS and SATA drives in a RAID 1 PowerEdge T110 II configuration

  Hello

  I have a RAID 1 configuration and one of the two drives in the array has failed.  I've removed and replaced by another drive hoping the Dell Perc adapter H200 would rebuild the mirror automatically, but it does not.  In Server Admin OpenManage virtual disk displays as degraded.  The issue I think may be the replacement drive is SATA where the original was SAS.

  Is there a way you can make the adapter accepts a SATA drive or is it simply not supported?

  SIV

  Hello.

  Dell controllers, including the H200 are not supported mixing SAS, SATA or SSD in the same table. They may, however, each separately constitute a virtual disk on the same controller. Consider replacing the disk failing another identical or higher capacity SAS drive.

• H200A PERC. SAS and SATA. Simple 2 extra HARD drives raid. Possible?

  Hello.
   
  Research in the server rack dell R210 II.
   
  Added records 2 x 300 GB SAS with a PERC H200A raid controller.
  The other two empty drive bays im looking to transfer courses two SATA 2.5 "HARD disk drives. Ive read you can mix SATA and SAS drives, is this true?
   
   
  I have two options to the raid configuration:
   
  the raid controller would be able to support two raid 1 RAID. 1 for the SAS drives and the other for the two SATA drives?   Operating system can see two disks.
   
  He would support a raid 1 for hard 1 & 2 discs.  Then with disk HARD 3 & 4 show the HARD drive directly on the server.  OS sees thre readers.  The drive in question and two others.
   
   
  I tried the dell chat, but could not get anywhere, as the helpdesk agent does not seem to know that you can google some caddy and buy the caddy to adapt to discs with no carts.

  [murmur] I'm wrong :), but I think the H200 supported not RAID, so if left unconfigured, the disks will be seen by the operating system as the person/no RAID disks.  Also, if I am wrong not :), the H200 supports a maximum of 2 virtual drives, so would not work two 1-disk RAID 0 and a RAID 1 (in fact, it probably won't allow you to create a single drive RAID 0 in all). [/whisper]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_dell_adapters/PowerEdge-RC-h200_User ' s%20Guide_en-us.pdf

  Sorry... I love you pc :)

• ASUS P6T7 WS - SAS and SATA RAID-0 / boot

  
  

  I am trying to determine the optimal configuration of HD to better use
  the 2 x SAS and 6 x SATA connections on the motherboard P6T7.
  I intend to fill all 12 available bays 3.5 "in the Lian Li PC-A77F and want
  to control all devices SATA 12 of the Mo without the use of an expansion card.

  
  

  1. is it effective to use a x 4 SAS to SATA fanout cable to configure a
  equipped with four SATA RAID-0 drives on one SAS channel?

  
  2. is it effective to use a x 4 SAS to SATA fanout cable to connect one
  SATA boot drive drive 1 + + 2 optical drives on one SAS channel data?
  (I realize boot must be BIOS configured via the Marvell SAS host utility)

  
  3. should I stick to a plan 'a channel and a device' and use the add-on controller
  for the SATA device rest four bays?

  
  4. If the answer to ' 3 is in the affirmative, what is the best use of channels 2 x SAS if all the»
  There are SATA devices? (bootable disk. optical media, or just a single SATA drive)

  
  

  Thank you

  1.

  I don't think that it is possible to use this motherboard connector fan-out cable single to multiple disks disk

• Re: Sat Pro A10 and Sat 10 - the difference - need new keyboard

  Hey all!

  New ID as I am garbage to remember the passwords/log on emails...

  I have a Satellite Pro A10, which needs a new keyboard - there's loads are circulating on ebay for Satellite A10 - but not the Pro - now I'm almost 100%, it'll be the same keyboard - right? the 'Pro' ILO denounces just usually extras bits and things qhizzy-, but basically they are the same hardware platform slot - i.e. the same keyboard between the A10 Sat and Sat Pro A10

  Anyone?

  : D thank you in advance for letting me sleep at night!

  I agree with you. There is not much difference, and the construction of the laptop is the same.
  I'm 100% sure that the keyboard is the same.

• PXI-5412 - discontinuities and dynamically modify the frequency with niFgen nodes of property

  I'm trying to find a way to eliminate discontinuities and change frequency/amplitude on the fly.  Is there a simple way to do this?

  Basically, my ultimate goal is as so:

  Table:

  Start Stop Freq Freq dt

  1                          100                     10

  100                      1000                   5

  1000-5000-10

  When you start at 1, then move to 100 after 10 seconds.  Then you would go from 100 to 1000 after 5 seconds.  And finally, you would go from 1000 to 5000 in 10 seconds.

  I use the niFgen Util creation frequency sweeping of data VI to create all the necessary frequencies.

  I use nodes of property niFgen to try to achieve.  I use a simple loop to move through a frequency table, and I update the frequency as follows:

  

  I have everything set up and works, the only problem is that I have large discontinuous jumps whenever the frequency gets really changed.  Unfortunately my oscilloscope are boring with the Print Screen function, so im trying to recreate using MS Paint:

  

  Clearly not the best artist ever, but you can get the general idea.  I get these discontinuities in the shape of V that are particularly sensitive to the peak of a wave.

  Someone at - it a good suggestion on how I should go about it?  I'll put in place the generation as follows:

  

  Looks like you are using the operating mode Standard to do this, correct?  The best way to go about this would be to use the frequency list mode, but the 5412 doesn't have this feature.  I have seen documentation that the use of property with Standard function nodes can definitely cause these kinds of discontinuities.  Another method is to use the arbitrary sequence mode, take a look at the niFgen "Arb Example.vi séquence" in the finder for example LabVIEW as a good reference on how to do this.