Mobility groups, failover on different subnets
I have read up on 5.1 and wonder how and if real failover on subnets is an option.
I understand controllers mg even customers roaming on different subnets.
How it works if your main "anchor" isn't alive to replicate the DB entry on the controller off-subnet? Say if die of my local WISN and the backup is in the next State, how the HA will maintain connectivity?
Thank you!
Yes, but tha ap will be the new configuration of the WLC. Also, users will get tunnelees to the wlc and be thrown out of this subnet. Then make sure you understand the ssid and ip clients will get when they associate to of different wlc. That should do it.
Tags: Cisco Wireless
Similar Questions
-
2 5508 a mobility-group autonomous migration
Hey everybody,
for some reason, our wlan controllers were built up to be independent instead of beeing a mobility group.
I would like to change that in order to be able to use all the features of the AH.
Let me describe our scenario:
two WLCs 5508 running SW worm. 6
-same subnet
-the two are running in mode master controller
-different host names, ip addresses, etc.
-all settings for the local wireless networks and AP-groups (except the APs themselves to these groups) are the same
-altogether now, we manage approximately 100 configured on WLC #1 half rounds, the other half on WLC #2
I don't know exactly why, but when that adjustment has been installed, someone already configuredHA for each access point...
for example:
-AP #1 WLC #1 WLC #2 secondary primary
-AP #2 WLC #2 WLC #1 secondary primary
but without WLC #2 configuration for AP #1 knowing that it would be foolish, correct?
so my question is: How can I do the migration under the best conditions?
is it easy as:
-disable the master controller on WLC #2 mode
-Configure the two WLCs in one group of mobility
--> WLCs negotiate their configurations for the APs
and everything is fine after that?
Comments appriciated. ;-)
rgeards, Manuel
First OFF... master controller mode. Then veriftywhat ap should serve as wlc #1 as the principal and wlc #2 of high school. Configure the belgo-chinois mobility to have the other wlc and ensure that relief ap is activated.
-
ASA 5505: VPN access to different subnets
Hi All-
I'm trying to understand how to configure our ASA so that remote users can have VPN access to two different subnets (Office LAN and LAN phone). Currently I have 3 VLAN configuration - VLAN 1 (inside), VLAN 2 (outside), VLAN 13 (phone LAN). Essentially, remote users must be able to access their PC (192.168.1.0/24) and also have access to the office phone system (192.168.254.0/24). Is it still possible? Here are the configurations on our ASA,
Thanks in advance:
ASA Version 8.2 (5)
!
names of
name 10.0.1.0 Net-10
name 20.0.1.0 Net-20
name phone 192.168.254.0
name 192.168.254.250 PBX
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 3
!
interface Ethernet0/6
!
interface Ethernet0/7
switchport access vlan 13
!
interface Vlan1
nameif inside
security-level 100
192.168.1.98 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address IP X.X.139.79 255.255.255.224
!
interface Vlan3
No nameif
security-level 50
192.168.5.1 IP address 255.255.255.0
!
interface Vlan13
nameif phones
security-level 100
192.168.254.200 IP address 255.255.255.0
!
passive FTP mode
object-group service RDP - tcp
EQ port 3389 object
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
EQ-ssh tcp service object
vpn_nat_inside of access list extensive ip Net-10 255.255.255.224 allow 192.168.1.0 255.255.255.0
access-list extended vpn_nat_inside allowed ip Net-10 255.255.255.224 phones 255.255.255.0
inside_nat0_outbound list extended access permits all ip Net-10 255.255.255.224
inside_access_in of access allowed any ip an extended list
Split_Tunnel_List list standard access allowed Net-10 255.255.255.224
phones_nat0_outbound list extended access permits all ip Net-10 255.255.255.224
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 Mac host everything
pager lines 24
Enable logging
timestamp of the record
record monitor errors
record of the mistakes of history
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 phones
mask IP local pool SSLClientPool-10 10.0.1.1 - 10.0.1.20 255.255.255.128
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global interface (10 Interior)
Global 1 interface (outside)
global interface (phones) 20
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (10 vpn_nat_inside list of outdoor outdoor access)
NAT (phones) 0-list of access phones_nat0_outbound
NAT (phones) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 X.X.139.65 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = not - asa .null
pasvpnkey key pair
Configure CRL
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
lifetime 28800
VPN-sessiondb max-session-limit 10
Telnet timeout 5
SSH 192.168.1.100 255.255.255.255 inside
SSH 192.168.1.0 255.255.255.0 inside
SSH Mac 255.255.255.255 outside
SSH timeout 60
Console timeout 0
dhcpd auto_config inside
!
dhcpd address 192.168.1.222 - 192.168.1.223 inside
dhcpd dns 64.238.96.12 66.180.96.12 interface inside
!
a basic threat threat detection
host of statistical threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image
enable SVC
tunnel-group-list activate
internal SSLClientPolicy group strategy
attributes of Group Policy SSLClientPolicy
WINS server no
value of 64.238.96.12 DNS server 66.180.96.12
VPN-access-hour no
VPN - connections 3
VPN-idle-timeout no
VPN-session-timeout no
IPv6-vpn-filter no
VPN-tunnel-Protocol svc
group-lock value NO-SSL-VPN
by default no
VLAN no
NAC settings no
WebVPN
SVC mtu 1200
SVC keepalive 60
client of dpd-interval SVC no
dpd-interval SVC bridge no
SVC compression no
attributes of Group Policy DfltGrpPolicy
value of 64.238.96.12 DNS server 66.180.96.12
Protocol-tunnel-VPN IPSec svc webvpn
attributes global-tunnel-group DefaultRAGroup
address-pool SSLClientPool-10
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
NO-SSL-VPN Tunnel-group type remote access
General-attributes of the NO-SSL-VPN Tunnel-group
address-pool SSLClientPool-10
Group Policy - by default-SSLClientPolicy
NO-SSL-VPN Tunnel - webvpn-attributes group
enable PAS_VPN group-alias
allow group-url https://X.X.139.79/PAS_VPN
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Hello
Loss of connectivity to the LAN is not really supposed all remove this command UNLESS your network is using another device as their gateway to the Internet. In this case configuration dynamic PAT or political dynamics PAT (as you) would make sense because the LAN hosts would see your VPN connection from the same directly connected network users and would be know to traffic before the ASA rather than their default gateway.
So is this just for VPN usage and NOT the gateway on the LAN?
If it is just the VPN device I'd adding this
global interface (phones) 10
He would do the same translation for 'phones' as he does on 'inside' (of course with different PAT IP)
-Jouni
-
Replication of different subnet
I need to configure the replication of an existing EQ group which has all of its interfaces on a subnet that is not routed; a newly staged group who will live in a different subnet. Initially, the two groups will be co-located for staging, but the new group will be moved to a remote site, but retains the private address that it is affected.
What is the best practice to configure replication? I just need to allow the routing on the iSCSI networks?
Yes, you need get the subnet that is connected to a router that will reach the remote site. You set up default GW for iscsi is what is used for replication. Replication between groups EQL is made via the port 3260 in an iSCSI session.
Kind regards
-
Setting up a virtual computer on a different subnet?
How to set up this configuration is all new to me.
Current context:
Internal subnet: 192.168.1.x
2 - 5.5 ESXi hosts. Each with 4 physical NETWORK adapters
Configuration is attached.
I have a physical server I want to virtualize but is in a different subnet.
Replacing the subnet: 192.168.10.x.I reason assuming that I'll need to add a physical NETWORK card to each host and assign this NETWORK adapter on the computer virtual requiring a different subnet? Or am I way off?
Thanks in advance!
If your physical switches supports VLAN's then I would say you think to reconfigure the ports for the ESXi host and tag/trunk ports to the VLAN necessary. And create groups of ports VM with the differnet VLAN-ID on the ESXi host. In this way, you can use different subnets on the ESXi host without the need for having dedicated physical rising for each subnet.
André
-
How to combine 2 VCenter with different subnet?
Hello
I had 2 x VCenter instance installed in two different subnet, internal production and one for the disaster recovery site, it is possible to make them connected to each other and then implement in the heart of vcenter beat builtin functionality?
Thank you.
OK, I'm a bit confused. You asked previously on vmotion or vcenter or esx hosts?
vCenter servers can be linked together without having to be in the same subnet.
Grouping of vcenters will allow you to have a single pain of glass view for the two vcenters and allow you to search your inventory full, but models are managed by the individual vcenters.
-KjB
-
vMotion between hosts on different subnets
Before you start, I'm a network engineer, not a server guru, please bare with me
Is it possible to vMotion a virtual machine to a host on an IP network to another host, on a different IP network?
Example:
Data Center 1 - 10.1.1.1/24 with VM in the 10.1.2.0/24 ESX Server
Same city, different site, binding fiber 10 GB between facilities 2ms latency
Data Center 2 - 10.2.1.1/24 in the 10.2.2.0/24 with VM ESX Server
Scenario:
vMotion a computer virtual network 10.1.2.0/24 to the 10.2.2.0/24 network where virtual machine, on arrival on the ESX 2 data center server, now uses a IP address of 10.2.2.0/24.
Any guidance towards a white paper or a guide would be greatly appreciated.
Thank you all for your time.
-Chris
Network engineer
Press Ganey Associates
vMotion is possible between hosts on different subnets, but unless your discussions presented to the virtual machines are on the same subnet, you will eventually drop the virtual machine on a VLAN different and IP addressing will fail.
There are ways around this, you could script the change of IP address / present several IP addresses of the virtual machine / or reservations DHCP to use, but you will need to ensure DNS etc. records are updated.
If you have some kind of load balancer, you could in theory balance workloads on 2 IPs hosted on the same VM, to solve the network ip address issues, although in the end, you'll want a VLAN tended to port VM coverage groups.
Good luck
-
Multiple RAC databases on IM even using different subnets for Public i / face
Hello. We are setting up a 2 cluster nodes. This group will be the host of several RAC databases. For security reasons, our network team want to create separate subnets for the application traffic to each RAC specific database on the cluster.
For example, request 1 to 2 application servers that will connects to database PROD1 RAC via a single subnet, application 2-3 application servers etc which will be connected to the database RAC PROD2 via a different subnet,.
In addition, the network team want to configure a subnet separate management DBA etc. will use to administer all the RAC databases and infrastructure in the cluster.
Version 11.2.0.2 grid infrastructure. The database versions vary from 10.2.0.x to 11.2.0.2. All databases will use RAC.
We want to take advantage of the features of earphone SCAN to support connectivity to databases on the cluster. 2199620 [https://cn.forums.oracle.com/forums/thread.jspa?threadID=2199620] thread suggests that 11 GR 2 supports several subnets, that seems to be exactly the functionality we need. Please can you confirm how it works and tell us any documentation (standard docs, whitepapers, MOS, etc.) which could help us to configure it.
Document referenced in thread 2199620 was not exactly what we were looking for and didn't translate too well in Google Translate.
Any guidance is appreciated. Thanks, Rich.
Similar topics:
https://CN.forums.Oracle.com/forums/thread.jspa?MessageID=9846298? (Double SCAN on multi cluster hosted)
https://CN.forums.Oracle.com/forums/thread.jspa?threadID=2199620 (scan earphone in VLAN OAM)
Published by: 887449 on 26-Sep-2011 01:41Hello
With Oracle 11.2, you can have multiple public networks accessing your Oracle RAC.
You must set the init.ora new LISTENER_NETWORKS setting so users are load-balanced on their network. Services are related to the networks so users who connect with network 1 will use a different service as network 2. Each network will have its own VIP.Impossible to use both network SCAN function because SCAN will work into a single network and on GRID 11.2 you cannot config more than a SCAN.
So, you can have a public network (for example, 10.10.10.0) with SCAN/VIP and another public network (e.g. 192.168.217.0) you will only use VIP on TNSNAMES.ora.
You configure a Service (A) on the network (10.10.10.0) and one other Service (B) on the network (192.168.217.0).
In the example above using (A) Service you will configure SCAN (scan host) and using Service (B), you must configure all address VIP.
Kind regards
Levi PereiraPublished by: Levi Pereira Sep 26, 2011 18:03
-
Not able to deploy images on different subnets
Hi guys,.
I'm having a problem of image deployment of T5565 for thin clients on a different subnet.
The first message that I got, was "the subnet of the device (s) in red color is not the same thing with its device management gateway. You want to send the task anyway".
I selected Yes, and finally the deployment will timeout with the following error: "job failed. Task become invalid before being sent".
I am able to update the agents on these thin clients with success, however, and these devices are discoverable.
Any help will be much appreciated.
Kind regards
Remo
This has been sorted guys. I had tried to deploy the image by using PXE.
Image without PXE deployment now works fine.
Kind regards
Remo
-
Unable to connect to storage as "different subnet."
Have just updated my LenovoEMC device to the latest version of the software (4.1.114.33421) and now get the message
"Unable to connect to the storage because it is in a different subnet.
but I can go to the Admin in the usual way, through devices and can change anything, as all the mapped drives as if it worked and all the data is visible?
Reset the system and all users etc., verified that DHCP is select rather than fixed, tried fixed without result.
Someone has an answer that works or is a reset?
Got it finally - works had to install a new version of Storage Manager - Version 1.4.8.33485
After installation, restart the PC only and ran it Storage Manager - it took forever, but she finally found my nas and created links to explore.
Can't believe that they a D A M N blip! in my previous post - AR even if you ask me.
-
Target subnet mask and the gateway in different subnets and clock error
Hi all:
Need help. I have a standalone PC operating a direct VI on a CFP with a crossover ethernet cable (developed on my laptop, compiled and installed as a standalone on the PC). When the VI runs on standalone PC version, everything works (click the button, analyzers are read), but the time being pulled from the CFP is wrong, and infact resets to December 1969, a default value. I am error checking, and no error is marked with the CFP, slaughter programmes. When I go to the MAX function, the time playing of the CFP is the funky time. Looking at the IP addresses, I generally use a very standard protocol (192.168.000.001 for the PC, 192.168.000.002 for the CFP currently running on the subnet for the pc and the PSC 255.255.255.000). However, when I apply this Protocol on the CFP through max, it gives the error "the subnet mask you entered puts the target and the entry door to different subnets." I am not versed enough well understand this, and what I read in 2 postings here, I tried to harmonize the IP numbers and the subnet, and they do not seem to help. When I put intentionally in false numbers IP or subnet default time synchronization time correct (pc), but functions block (as expected). It is certainly not an issue of PC zone.
Anyone can offer any guidance?
Currently runnig LV 8.2 with drivers of 2009. PSC 1804 with MAX 4.6.
I appreciate all help.
Best regards;
GIS.
OK, I solved it. FYI: for those who are not aware of the IP: IP of the host and default gateway server to the same value. My work for the host computer are 192.168.000.001 and subnet masks can stay 255.255.255.000. The CFP has been set to 198.162.000.002 with a 90.00.00.03 DNS. Time server has been blocked by the Norton 2009 Firewall (even with an exception) and thus the cruxt of this issue together. I had to uninstall completely from this "software". I hope this helps.
-
Install MX922 on 2 different subnet?
I have a LAN into 2 separate LAN or subnets. 1 LAN is 192.168.1.x and LAN 2 is 192.168.2.x. I installed a MX922 installation method using the network on all computers on the LAN 1 without problem. The MX922 is located on LAN 1.
I tried to install the printer on a PC on the LAN 2 but install fails, claiming that he cannot find any printer on the network. My guess is that he is only looking on the scheme even the installation of PC is on AND the installation of the software does not allow you to set the IP address to make it look like the printer.
I know that all firewalls are disabled and 1 LAN 2 LAN communication is very good because this printer is replacing another printer set up exactly the same way and this printer set up is still workng fine.
I was thinking about putting the PC in question 'temporarily' on LAN 1 to install the printer and then back to LAN 2 and then manually reconfigure the port to address different IP, but when I try to configure the printer port on a PC on the LAN 1 where the printer is already installed it gives the error that there are no configurable parameters for the port. So I don't think I'd be able to configure the port once it was back on LAN 2.
I can't be the first person to try to install one of these printers in an office environment where there are several subnets that all need to print to a central printer so I think there must be a solution, but we don't find where in the documentation or on this site that I can see. If anyone can help me please?
Thank you.
Solved!
It can be done even if I emailed Canon support and their response stated that Canon printers are not able to work on multiple subnets.
The solution is:
1. change the PC concerned to the same LAN as the printer so they are both on the same subnet. At the time of installation, the printer and the PC must be on the same subnet.
2. then install the printer normally.
3. after the printer is in place and works very well on the given PC, then return to the original subnet that it is supposed to be on.
That's all!
There is a workaround solution. For a computer that has many PC on several different subnets, it would be a huge task. For an additional House with 1 or 2 subnets and a few PCs, it is a pain.
-
Mac, WRT 54 G, can I access a MFC9320 brother on two different subnets?
(domestic use) I have a USB Server that I can access my USB printer on two different subnets and I was wondering if I can do the same thing on the WRT54G. I use 192.xxx.xxx.x for internet use and 198.xxx.xxx.x for each thing, like file sharing of multiplayer games, etc. Only, I named the 'locations' to 'Internet' or 'Games' (with games being used for everything else). With the USB Server set to "ZerocConfig" I could access USB printers on both. I could set up the printer with a static IP printer 'Place' and then change location every time we wanted to print to it, but I would like to save a step. It's not that big a deal for me, but have to "Remind" everybody whenever they wanted to print something on it, would get old. Don't want to hang the brother to the USB Server if I have the wireless. It is not the smallest thing in the world to find a place for it in any case.
I guess my other question would be, taking the other subnet is it safer (from the internet) using this way he or she is just in my mind. I did the on a third location of 'White', the family put their computers (no IP #) when they are just playing games, homework, etc..
Thank you
I don't think it's possible to run the USB printer on two different subnet. There is no such feature on the router.
-
WLC and AP on different subnets
I want to add a new access point to my existing controller. Currently I have about 15 AP is connected to one vlan separate mgt for the AP, vlan 10. It's shared resources for the controller and the other VLAN user as Private, Public, etc. WVoIP. I already started to implement EIGRP network instead of having a large layer 2 vlan would be network. In one of the more recent places I'm routing, I have a new AP to connect. I'm trying to make sure that this design will work before I implement. So I have a 3560 connected to my core 4506 with a 3 layer connection. EIGRP works as well. I intend to have the 3560 intervlan routing with vlan voice, data and wireless. The problem I see is how can I get the AP to speak with the controller as they are on different subnets, more a metro E 'WAN '? Any suggestion would be great.
As long that the ROUND was started locally first, this TOUR will be the ip address of the WLC. If you want to fix the ROUND on a different subnet from L3, then configure ip helper-address the ip address of each wlc management. then configure the ip forward-Protocol udp world 12222 & ip forward-Protocol udp 12223 on the router of L3. This with the help of intellectual property, will allow the s TURN to join the WLC on the other end.
-
Copy configuration WLC wlc next in the same mobility group
Hello
We have a 4400 WLAN operational controller. We intend to deploy a new controller in the same mobility group.
How do we configure the second WLC? From scratch, or we could for example use backup configuration of the first WLC (just to change the address-ip/hostname etc.)?
ARO
Mikko
Or the other works, but remember that reproduction should be the new controller to be off the grid to avoid intellectual property conflicts. I like to build from scratch, and then to ensure that the same configuration settings, use WCS to push models. Local on controllers do is ok, if you only have a few, but if you have more that 5-10 you will find keeping all the controllers of the same becomes a management nightmare.
Maybe you are looking for
-
Browse folder to download firefox can only chrome can
Topic: browse folder upload file <input type="file" id="file_input" webkitdirectory directory /> webkitdirectory can browse folder in google chromebut firefox cannot Please, implementand let me known via email [email protected] Thank yo
-
Yahoo mail load in my Firefox browser in different sizes.
Initially, it was a regular size; for a few weeks, there has been greater, but yesterday and today it is smal is unreadable. Change the screen resolution makes no difference. He also did not this in Windows Explorer again. How can I fix? Thank you. (
-
HP ENVY 750-055XT: HP download win 10 for win 7
I bought a refurb unit. He came "upgraded to win 10 64. But there is no win 7 files to restore. I have a new win 7 64 pro license. On the CD. How can I install and lose 10 WIN. I want to have anything to with win 10 in the computer. I have the s
-
Is there a form/technique of Toshiba email address?
I realize this is probably not the best place, but to research throughout the section of the support (before the forum) I don't see one anywhere. It's another to raise a warranty claim which is on the top. Only, I have a quick question for the custom
-
15 - g004nt: an HDMI output for 2560 x 1080?
Hi, is it possible HDMI port to my laptop at the exit to 2560 x 1080? 15 - g004nt, 10 Windows? Thank you.