Model SR1930NX and Raid level 1

Similar Questions

• Satellite A300 - 234 MODEL NO. PSAGCE. What RAID levels?

  Satellite A300 - 234 MODEL NO. PSAGCE. What RAID levels? 0 or 1? or 2,3,4,5?

  Hello

  As much as I know the laptop does not support (hardware) RAID
  You won't find anything in the BIOS.

  But a software raid was possible;
  For this you need a RAID tool.
  Check this box:
  http://tldp.org/HOWTO/software-RAID-HOWTO.html

  In addition the laptop was equipped with a HARD drive I m not very well if a second HDD could be installed check the second HDD bay if the connectors are available then you could install second HDD

  Welcome them

• Problem of ESXi 5.5 and RAID

  So I have an ESXi host and RAID problem with a motherboard for Intel Server S1200V3RP. Basically, the problem is that the 5.5 ESXi host is not recognizing the RAID array set up with the utility integrated. See the images below for what I mean.
  
  

  Click here
  Click here
  Click here

  
  I did some research and my research has pointed out to me the possibility that this on the Intel Server raid controller is not actually a hardware controller but a piece of software built using the computer as controller. My research basically tells me that ESXi is super picky and don't play well with fake RAID. Although I may be wrong on this subject the behaviour of ESXi and each site Web I found says that this may be the case. I tried integrating storage and RAID drivers in the iso ESXi, I tried to update the BIOS chipset with the deployment server disk, and the management and I tried a USB installation with the drivers but nothing seems to solve this problem.

  Since ESXi does not the table as something other than dedicated disks, I tried an inventive work around by choosing the AHCI BIOS and install ESXi 5.5 mode host on a dedicated disk (volume 0). Then I switched back to RAID and used the Intel Rapid Storage Management utility to configure a RAID5 to three remaining disks. It seems to work very well and I was able to access the vsphere ESXi environment. However I couldn't see the RAID volume again on vsphere storage.

  I've plotted a plan where I could load the drives as individual data on the host and virtual server stores use the disk management utility or another program for RAID 3 hard drives together so that they appear as a single volume. However when I booted the system upward it appeared that the integrity of the RAID5 degraded after the addition of each drive separately (probably because he had to load a VMFS on each disc, thereby breaking the table). So this probably won't work (and even if it's possible, it's probably unnecessarily complex).

  
  Click here

  
  So yes, I don't have really a clear idea of the place where to go to get the RAID controller integrated to be read by ESXi. I was told that there may be compatibility issues between VMware and my Intel server model, but I checked and its on its list of approved so compatibility it couldn't be her. I guess I could just stick with dedicated drives and load the HARD drives as data stores, and then use software RAID across virtual machines - but I am concerned about the way in which redundancy will include when we drive finally fails (could I just Exchange on as a hardware raid?). I always thought that software RAID (especially on windows server disk management) smb read and write speed is terrible compared to hardware RAID.

  Anyone know a solution to this problem or where I could go from here?

  I did some research and my research has pointed out to me the possibility that this on the Intel Server raid controller is not actually a hardware controller but a piece of software built using the computer as controller. My research basically tells me that ESXi is super picky and don't play well with fake RAID.

  ESXi is not 'super picky' here. This kind of fake-RAIDs that are so common on desktop PC motherboards and entry-level rely on specific drivers provided by the hardware vendor to work really. And suppliers basically only provide Windows drivers in the first place. Any other non-OS Windows would be faced with the same question. Try installing a Linux and that you will not see your RAID volume either.

  Yes, your motherboard does not use a real independent of hardware RAID but a cheap RAID/fake-software controller. See the Intel website:

  http://Ark.Intel.com/products/71385/Intel-Server-Board-S1200V3RPS

  RST (0,1,10,5) RAID and ESRT2 (0,1,10) RAID Configuration software

• HP OfficeJet 8600 not return status and ink levels

  Hello

  I have a new one (from this summer) a model HP OfficeJet 8600 (N911a) AIO

  Just run out of black ink on startup of the cartridges provided all.  At purchesed an Office Jet Valuepack 951XL and 950XL in preparation.

  So I replace the Starter 950 black void for the black of 950xl, all ok thing prints, scans/copies fine

  But when I launched the web interface to check the status of the printer status and ink levels are in red and I can't get the ink gas monitor section.  Screen attached.

  If I try to launch the HP printer Assistant for model nothing happening!

  Any suggestions please?

  RGS

  Steve

  

  Hi all

  OK I solved this problem. But since then, I had cause to rebuild my main desktop PC is so BRAND new HP software has been installed and the question has not reappeared.

  Thanks for everyone for entry

  Steve

• How to change mini H730P RAID level

  Hello

  I read H730P the user guide:

  

  Who mentions the possibility of change of a virtual disk's RAID level, and adding capacity of a virtual disk. However, there are no instructions on how to do it. I looked through all the menus can be found in the BIOS RAID config, I cannot find anything to do with the change of RAID level. I also watched menu iDRAC for storage options.

  Can someone point me in the right direction? Currently, I have two physical disks in SAS in a RAID1 and would add more than 3 drives to convert it to a RAID6 and increase capacity.

  Install OpenManage Server Administrator, go to storage, PERC, virtual disks and select Reconfigure in drop-down list of tasks available for your table.

• What raid level do you use

  Hello

  Just want to hear what kind of raid level you use, type os drive and what kind of applications running on this VM VDi.

  I read a lot of articles of the IOPS / s and I just want to see what people are using...

  Most of the time I saw customers using Raid 5, but here again it depends on what environment you're using which users you anticipate, Basicallt the % of reading and taking Raid penalty and Cache into consideration

  As you say you have read some Documents I found it very interesting http://www.vmware.com/files/pdf/techpaper/view_storage_considerations.pdf

  If you have a document that will help you really share

• Suggested for the RAID level configuration

  Hallo,

  I have a server 4core, 16 GB of RAM and 4 SAS 140 GB discks whith fiber channel EMC SAN. What is RAID level suggested for reduncancy and performance?

  RAID 1 + (a single disc advanced to other uses)

  RAID 10 (is really necessary for an ESX configuration?)

  others

  RAID 5 (suggested for VMFS, but not for a simple configuration, ESX)

  RAID 6 (not suggested because that too slow)

  Thank you

  As for local storage (as opposed to the EMC SAN) I'd go with RAID 1 + 0 for optimal performance. If you have an EMC SAN you probably store most of your VMs on the San. Your local storage space will be for your ESX installation and perhaps a data store for testing. Thus, you do not want to go with a RAID that offered high performance and redundancy, even if she does a high-cost disk, because the size is not you primarily on local storage.

  As for your EMC (Clariion AX regardless), you will want to cut LUN based on the needs of performance of your virtual machines.

  LUN RAID 5 for your regular VMS

  LUN RAID 1 + 0 for SQL (Oracle or Microsoft SQL SERVER) or machines virtual Exchange

  Just my two cents on the views of storage vary, and the right answer for you depends on your environment.

• HP laptop: enter the model number and get a "game too many results.

  My HP laptop dies after 6 weeks. When I contact support, he asks the model number. I enter: say "15-ay041wm" is what the box and laptop. I get a reply that says.

  "Sorry, too many results match your search for 15-1y041wm.

  "So I try HP Notebook, I get the same mesaage above, except with the HP laptop ' instead of '15-ay041wm.

  Because no matter where I'm going, he wants the model number and I give, I can't help. No cat, no nothing.

  So someone can tell me how to get support?

  If HP is unable to handle the number of model of it's own computers, so I'm not very confident.

  Here are the free support number to call in the USA/Canada... 1 800-474-6836.

  Now here's another question, you can report to HP on if you want...

  You must stay online and listen to the automated assistant trying to talk to you to talk to a representative... visit the HP website... go to this support forum (which has no official presence in HP), etc.

  After a minute or two, the Assistant to say, if you can't get online, will stay on the line to speak to a customer services representative.

  This is when you will have the opportunity to speak with a support person and report the problem to open a pension case.

• the model number and imei of iphone 6s can editable with the software or anything else?

  I want to know this weather model number and imei number can be changed to an iphone camera? my phone has been replaced but same issue was at new device but the imei and model number was the change of the new device. is this possible? that model number and imei number can be changed through software or reset of the device.

  No, they cannot be changed.

• Aspire BIOS and RAID m3970

  Hello

  I noticed in the tab BIOS for an Acer Aspire M3970 and then advance under the integrated devices, there are options for the SATA mode on "Native IDE", "AHCI" and "RAID".

  I would like to know what RAID modes are supported by the RAID option on this forum. I can't seem to find this information anywhere does support at least 1 RAID when you have two drives?

  Any help would be great. Thank you.

  This system supports Raid 0, Raid 1, Raid 5, and Raid 10 configurations.

• Cannot run or debug app on the device after the update Momentics 2.1 and api level to 10.3

  Dear Blackberry support

  I have improved my Momentics IDE to 2.1 and api level to 10.3

  After upgrade I can not run my application package, and when I run the Momentics show pop up error:

  Click here to see the photo of the error

  I don't know what is happen?

  Please help me solve this problem, any help is appreciated!

  Thank you

  Hey,.

  Finally, I found the solution for this problem

  Create new project of Blackberry (just create an empty project) and then copy all the CBC, assets of the old project to the new project, also the bar - description.xml and .pro file

  And now everything is ok.

  Thank you for all your help

• VLANS can be configured at the vSwitch and Portgroup level?

  Dear friends,

  I hope that all do you good...

  Two statements are true about groups of ports and VLAN defined on a switch vNetwork Standard? (Choose two)

  A. A VLAN can be configured for the entire virtual switch or on groups of individual ports

  B. several groups of ports can specify the same VLAN

  C. VLAN can only be configured on individual port groups

  D. several VLANS can be specified in a port group

  VLANS can be configured at the vSwitch and Portgroup level?

  B. several groups of ports can specify the same VLAN

  C. VLAN can only be configured on individual port groups

• Can anyone help? My catalogue LR4 suddenly started showing pictures to folder and subfolder level 0, only shows that good number of images to the file level. Help would be most welcome. Thank you.

  Please can someone help?

  My catalogue LR4 suddenly started showing pictures to folder and subfolder level 0 and only shows the correct number of images at the file level.

  Your help would BE welcome.

  Thank you.

  Click on the sign in Control Panel folder + and check "display the Photos in subfolders.

  

• Difference requestlevel and operational level

  Hello
  
  I have to do a presentation on IOM next week and I'll have to explain some concepts of the IOM to people who have never heard of the IOM.
  However, I'm strugging with the difference between the operational level and the level of query of an application.
  I set up this fine in my approval of IOM policy, but I'm having a hard time explaining this to others.
  
  Anyone who could help?
  
  Thank you
  
  Steven

  Level of demand:

  level 2 of the approval process
  Application may be rejected in 1 shot
  At this stage no request child

  Level of functioning

  level 3 of the approval process
  Request of parent will stop in the child at this stage applications
  Each request of the child can be independently approve/reject

  http://docs.Oracle.com/CD/E14571_01/doc.1111/e14309/request.htm#CIHIEEHF

  Published by: Rajiv Dewan

• RAID 1 and Raid 0 410 XPS replace crashed HD?

  My XPS410 is running Vista Home Premium and Raid 0 will not start.  I know diagnosis (and the noise by clicking on him) that one of my HD is dead. : smileysad: I bought 2 500 G HD to replace my 2 160 G disks and want to configure Raid 1 and then reload VISTA.  I have Raids was not addressed in the past and want to get this right.  All the instructions would be appreciated.