modulation toolkit for labview for embedded controller PXI-8106

Hello

I have an on-board controller: 8106 PXI OR PXI 5661 and 5671. He came with DAMA RFSG but not the Modulation Toolkit (TM). Now I cannot access some screws RF Toolkit as NI DAMA close.vi etc. I opened a code that uses this DAMA close.vi and since I donot have probably MT, I can't run since the claim code to choose the path!

I checked for the TM in the start menu-> all programs-> national instruments-> modulation but in vain. Also, I opened MAX and under "Software", I could find DAA, pilots RFSG etc but not the Mt.

When I checked online it says I have to buy the cd/dvd of MT. If I do, how I run on my controller?  What are my other options?

PK

Hello

I think I solved the above problem. I had to install the RFSG and ACD for labVIEW. For some reason, the equipment was delivered to me with DAMA and RFSG, but only for C. This part was misleading because I saw on my National Instruments system but not the DAMA DAMA and RFSG vi. Also spectral measurement Toolkit (SMT) has not been installed. SMT is a MUST for the good functioning of the RF VSA. After you install the required drivers and tool boxes, I am able to run and use the VI completely.

Thanks for your support Abhishek.

PK

Tags: NI Products

Similar Questions

  • PXI-8106 RT

    Hey, evry.

    I just got controller PXI - 8106 RT and wanted, as usual, "thin" with Firstware, but...

    .. are "F4" key during startup - nothing happened!

    Then... Should there be a Firstware on RT controller?

    ... Not a word "combat manual, of the by..."

    Thanx in ADV

    Ok thank you!

  • Is there a Module NXT for LabVIEW 2010

    Is there a Module NXT for LabVIEW 2010?  If not, are there plans to bring a available and if so, when?

    Hello

    I found a link to a download for the module 2010 here.

    I hope this helps.

  • Internet Toolkit for LabVIEW 2012 64-bit

    I have an application which is currently written in LabVIEW 2009. It requires the Internet. I try to open it in 2012 of LabVIEW (64-bit) (using Windows 7 64-bit). LabVIEW 2012 does not find the box at Internet tools since he has been deprecated in LabVIEW 2012, so LabVIEW complains.

    So I downloaded the toolkit LabVIEW 2012 Internet and tried to install it. When the Setup program tries to run, it stops with an error message that says:

    "NEITHER LabVIEW 2012 (32-bit) or more must be installed before installing OR.
    2012 Internet Toolkit LabVIEW. »

    Can someone tell me where I can find the Internet Toolkit for LabVIEW 2012
    (64 bit)?

    Thank you

    -Ray

    Since you seem to understand that the Internet Toolkit has been deprecated, I do not understand your question. There is no 64-bit version of the tool. In fact, it has very few tools that do not have a 64-bit version. In order to use the old, 32-bit version, you must use it with the version 32-bit LabVIEW, as said the message.

  • Third-party licenses and Activation Toolkit for Labview 8.5

    There are any third-party licenses and the Activation Toolkit for Labview 8.5 as LV2010. PLS help...

    I know what you're asking, and in the other thread, said you it was for 2010 only. There is a support for 2009, but not for your old version. Go with the suggested dongle or upgrade your version of LabVIEW.

  • update problems. Adobe Player for embedding 3.1 Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207 extend Script Toolkit 3.5.1 update Det oppsto en feil under nedlasting av denne oppdateringen.

    Adobe Player for embedding 3.1

    Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207

    Extend Script Toolkit 3.5.1 update

    Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207

    Oppdatering av CS Live-tjenester for CS5

    Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207

    Adobe XMP panels CS5

    Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207

    Adobe Device Central CS5.0.1

    Det oppsto en feil under nedlasting av denne oppdateringen. Avslutt og Prov. pa nytt senere. Feilkode: U43M1D207

    Help creating cloud / cloud creative applications download error

    http://helpx.Adobe.com/creative-cloud/KB/error-downloading-CC-apps.html

    Try direct updates
    https://www.Adobe.com/downloads/updates/

  • Installtion of Labview RT on the PXI controller

    We have a 8106 controller PXI that runs on the Windows operating system. We want to make it work on real-time OS of NOR. What are the steps I need to do to install this. Vascular when I boot in the BIOS of fron LabView RT, it displays "control transfer to the user program. System not configured, restart... ». I am able to connect it to MAX by the host PC and able to install Veristand 2011. But it does not reflect while the boot controller.

    Converting Windows a RT, there are some very important things that you must do to handle the conversion. big is your hard drive.  Your hard drive needs to be formatted with a FAT32 partition - probably formatted Windows NTFS, RT cannot read or use.  Convert your drive will be a manual step for you; If you follow these steps, you can use a disk RT PC Desktop Utility to perform the Exchange against (these instructions with a PXI-8106 module):

    First of all, must be a FAT32 partition on it and the format.

    1. Acquire a drive Flash USB 256 MB or more.  Plug it into your host computer.
    2. Image/Format the USB Flash drive via MAX
      • Under tools of-> creating USB utility MAX desktop PC
    3. Plug the USB key into 8106
    4. Enter the BIOS of 8106 using the "Delete" key
    5. Go to the menu "LabVIEW RT" and "Priming" the value "" Windows / other OS '. "
    6. Press F10 to save and exit, restart the controller.
    7. Enter the BIOS of 8106 using the "DELETE" key (we had to put the controller for Windows / Other and restart the computer to enable USB be detected/used)
    8. In the 'Boot' menu, make sure that "USB HDD" (probably also has your mfg of the inserted USB) option is #1 in the startup list (using keys + /)
    9. In 'Advanced-> Integrated Peripherals' ensure 'Legacy USB Support' is [ENABLED].
    10. Press F10 to save and exit, restart the controller.
    11. The startup controller using the USB flash drive.
    12. In the USB Flash Drive Options, choose the 6 'Options of Format' option (according to the image of the flash player, can say another thing, but option # is the same).
    13. Choose to format the drive, use the Option #2 in the format "Erase all Partitions on the disk and create a new single Partition" - This clears the disk partition information and creates a single FAT32 partition on the drive.
    14. FAT32 format (DO NOT use the use of a 8106 - BIOS does not include the system of dependency files).
    15. Once completed, restart the controller (to do this, you can use Option 9).

    Now, we must get the controller to think that it is a PXI and not a desktop RT PC controller

    1. Enter the BIOS of 8106 using the "Delete" key
    2. Go into the menu "LabVIEW RT" and "Boot" "LabVIEW RT safe mode" value
    3. Press F10 to save and exit, restart the controller.
    4. In MAX, find the device to remote systems.  Right click on the device and choose "format disk".
    5. Once you format the disk, the controller will think it is a PXI controller.
    6. (You may need to remove the MAX controller and press F5 to detect again for updated images)

    Now we are going to put the controller in RT mode so we can use it.

    1. Enter the BIOS of 8106 using the "Delete" key
    2. Go to the menu 'LabVIEW RT' and 'Start Configuration' value 'LabVIEW RT'
    3. Press F10 to save and exit, restart the controller.

    There you go.  Now you are ready to rule the world in a deterministic way.

    -Danny

  • That means that a PXI embedded controller is NOT certified "operation 24/7?

    Only a few embedded real-time Controllers PXI are certified 'operation 24/7': RT NI PXI-8110/08/06

    As I intend to build a PXI system with a controller real time embedded for continuous security monitoring, I would like to know if this means that the other ones (RT NI PXI-8106/04/02/01/83/45) are not designed for permanent operation.

    Thanx.

    H.L.

    Herlag salvation,

    Our PXI systems are highly reliable in difficult operating conditions. For this reason, NEITHER offers an extended temperature and versions of operating 24/7 of its embedded PXI. These embedded controllers use a more robust hard drive designed for reliability in the extremes of high and low temperatures and duty cycle of 100%, a 24/7 operation.

    NI PXI-8108 embedded controllers for example are available in two versions to tackle different environmental and operating conditions. The main difference is that the extended version of temperatures and 24/7 operation use a different hard drive. The hard drive in the scope of temperatures and the version of the operation 24/7 has a capacity of 40 GB (minimum) against the (Minimum) 60 GB hard drive used in the standard version of the controllers.

    designed for reliability in low and high temperatures, extremes and 24/7 operation. The standard version of the controllers has a temperature of 5 to 50 ° C and a temperature of 40 to 65 ° Cstorage. The scope of temperatures and 24/7 version operation has a 0 to 55 ° c operating temperature and a temperature of -40 to 71 ° Cstorage.

    The hard drives used in standard versions of these embedded controllers work in an operating range of 5 to 50 oC and a temperature of 40 to 65 ° C storage and can operate at 20% for eight hours a day, five days a week, similar to the PC and laptops.

    Running extended temperature versions and 24/7 have a 0 to 55 oC operating temperature and a temperature of -40 to 71 ° C storage and can be used for applications requiring continuous operation, upward to the market 100% factor, 24 hours byday and seven days a week.

    Hope this helps.

    Kind regards

  • Can I use PXI embedded controller connected to the PC under LINUX operating system

    Hi all

    We ara tries to connect to PXI8106 (in 1042 chassis) to PC under LINUX via ethernet (cable cross at the moment), is the version of labview 8.5.

    Can I use PXI embedded controller connected to the PC under LINUX operating system?

    If Yes, where can I find its configuration in the .ini file?

    Thanks in advance.

    Hello bachir_elec,

    I'm sending you two links that I don't provide the information you need.

    Using Linux on an Embedeed PXI controller:

    http://digital.NI.com/public.nsf/allkb/821E0C115A3B4EF286257069004B8352?OpenDocument

    Configuration of your PXI Linux system:

    http://digital.NI.com/public.nsf/allkb/5CEEC941FB7B0488862573F700653B21?OpenDocument

    You can take a look?

  • LV Report Generation Toolkit for Microsoft Office said "this VI or element belongs to a library that has expired or improperly licensed."

    I downloaded the LV Report Generation Toolkit for Microsoft Office for evaluation with LabVIEW 2010. Examples to help get a lot of errors, including "the Subvi is not executable. You must fix any errors in the Subvi before this can run VI. "and"this VI or element belongs to a library that has expired or improperly licensed. "

    I decided that I wanted to evaluate the Toolbox instead of putting an activation code during installation. Installation went well.

    How can I get the examples from this LV package to run so that I can evaluate it?

    A computer restart was costing the day the day to solve the problem.

    Installation of the toolkit does not have a reboot of the system, but it seems to need i.

  • HP-530: Driver for Ethernet controller card

    More than 4 weeks that I was looking for Ethernet Controller card in the laptop HP-530 for the Windows Vista Home 64 bit not this to 32 bits, it does not work

    Who can help me?

    I've had various emails sent to support, but not one answer, only with: NOT for us!

    Your laptop is the intel® 82562gt network card

    Try the next download driver Intel

    https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=18718https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=18718

  • Satellite A100 (PSAA8): need driver for video controller

    Hello

    I bought a new Satellite A100 (PSAA8) and re-installed Windows XP Pro. I downloaded some drivers including Intel Display Driver and Flash Media Driver, etc. from the web and installed. But I can't find the driver for video controller, so I still have the questionmark beside the video controller in Device Manager. Do you know what kind of driver he is? Where I can download for the video controller & what driver?

    Thank you
    Rona

    Hello

    HE = display driver or graphic driver video driver. All of this means the same thing.
    The suggested site, you will find the driver. Please remember to use the correct driver, because there are different units A100.
    I checked this pilot site and it seems that the most recent display at the moment driver is 14.18.2.4436 version

  • No driver found for network controller for - Pavilion dv6 - 6188ca

    I had to reinstall windows 7 pro OS as my laptop I was not able to start.  I did not use recovery CD.  I used windows 7 pro install CD and with a product key valid, now everything works except for LAN wireless.

    In Device Manager, I have a yellow mark for network controller and says driver not found. I tried all the drivers listed for this model on the HP support site, but without a bit of luck. (there are 8 network driver listed for this model on the HP support site)  There is also no specific driver that is listed as "Network controller" from the HP site.  My laptop uses the 4313 Broadcom 802.11b/g/n Wi - Fi and Blutooth 2070 (handset) 2.1 adapter. Bluetooth works very well because he is able to see other Bluetooth devices nearby.

    How can I solve this problem? Where can I find the driver for the network for this camera controller? Any help would be much appreciated. I havn't tried to connect via LAN and let windows search for a suitable driver for this laptop.

    Hello:

    This wireless Broadcom driver should work for you...

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-107849-1&cc=us&DLC=en&LC=en

  • n204tx: error installing driver for ethernet controller

    I received a message during the installation of drivers for ethernet controller... I don't know what to do... Try 2 months.

    You said to make the necessary changes in networks adatpters... but I do not see any which arms power tab when I click on network adapters.

    OS: Windows 7 Ultimate

    Model: n204tx

    Waiting for yoyour answer...

    Hello:

    See if it works...

    1 install the Intel chipset driver and restart.  The second file on the list, it's self installation of the file.

    https://Downloadcenter.Intel.com/download/20775/Intel-chipset-device-software-INF-Update-utility-

    2. then install the driver from realtek ethernet directly from realtek.   a 3rd on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  • Dimensions of 160 cable pins for the NI PXI-2530 b

    Hello

    My mechanical design team wants to know the measures of the 160 cable pins for the NI PXI-2530 b. It will take a while before we get the cable we ordered. I couldn't find a data sheet with details of the measure; are they? Alternatively, y Figure 1 in the Installation Instructions to scale? : http://www.ni.com/pdf/manuals/375656b.pdf

    Thank you!

    Hi JKSH,

    I'm sure you've probably noticed, that the specific documentation is not accessible to the public. Please create a demand for service by clicking here and using the tools on the right side of the screen. Once you have created a service request, we continue to assess your situation and we hope to get you the documentation you need. Although parts of it may be, I'm not quite sure that figure in the manual that you have accessed is perfectly to scale. So, contact National Instruments more directly can be a better option for you.

Maybe you are looking for