Modulation Toolkit PLL filter setting

Similar Questions

• Modulation Toolkit screws sbRIO-9651

  Hi all
  I try to help solve some difficulties with my current developments of the LV.
  Currently, I am working on implementing some transmission of packets using sbRIO-9651 interfaced with a programmable TRANSMITTER/RECEIVER. Unfortunately, a few screws (Resample(complex_cluster).vi MT and MT demodulate PSK.vi) run on the sbRIO. These screws are part of the LV modulation toolkit and some dll which fail to load into the sbRIO due to their incompatibility with the platform OR Linux RT-dependent.
  Anyone know of workarounds. Any help or suggestion would be welcome.

  Thank you very much.

  Bachir

  Bachir,

  Is it possible for you to open a DMA FIFO or some other form of data flow of the sbRIO to the host?

  A suggestion I have for her resample VI is to use the button Reechantillonner VI, who hails from LabVIEW.  I can't confirm that this will work on the sbRIO, but you can try.

  The nice thing about the modulation toolkit is that most are open to be viewed by the user.  In addition, most of the code is written in LabVIEW.  (Not very easily), you could look at the code and try to reproduce them in a fashion that will focus on the sbRIO.  You may even be able to find the place where there is no call to a DLL and try to eliminate these dependencies.

  Is there a specific reason to use the sbRIO rather than a RIO USRP?

• modulation toolkit for labview for embedded controller PXI-8106

  Hello

  I have an on-board controller: 8106 PXI OR PXI 5661 and 5671. He came with DAMA RFSG but not the Modulation Toolkit (TM). Now I cannot access some screws RF Toolkit as NI DAMA close.vi etc. I opened a code that uses this DAMA close.vi and since I donot have probably MT, I can't run since the claim code to choose the path!

  I checked for the TM in the start menu-> all programs-> national instruments-> modulation but in vain. Also, I opened MAX and under "Software", I could find DAA, pilots RFSG etc but not the Mt.

  When I checked online it says I have to buy the cd/dvd of MT. If I do, how I run on my controller?  What are my other options?

  PK

  Hello

  I think I solved the above problem. I had to install the RFSG and ACD for labVIEW. For some reason, the equipment was delivered to me with DAMA and RFSG, but only for C. This part was misleading because I saw on my National Instruments system but not the DAMA DAMA and RFSG vi. Also spectral measurement Toolkit (SMT) has not been installed. SMT is a MUST for the good functioning of the RF VSA. After you install the required drivers and tool boxes, I am able to run and use the VI completely.

  Thanks for your support Abhishek.

  PK

• I can modulate the fsk and qpsk without modulation toolkit?

  I develop didactic modules related to modulation fsk and qpsk for begineer students learning in labview, my question is: can I make VI involving fsk and qpsk modulations, but only using labview?

  I don't have the modulation toolkit and examples that I found using it

  thnks

  Where did you find examples?

  You can still write functions using LabVIEW. Modulation Toolkit gives you the FSK, QPSK pre-written routines. You can write these routines yourself using the basic mathematics and features in LabVIEW signal processing.

  Please let me know if I answered your question.

• How can I make a copy of the FAQ module or the filter on language?

  Hello

  is it possible to make a copy of the FAQ module? I need to have FAQS in various languages.

  I can add event, photo, new ANDS media modules, but not a new module FAQ.

  I also found that you can add a category and view the frequently asked questions with the filter: cr or individual filter. But where do I add the category name to filter?

  Solved!

  Quick fix: the ID is used for the name of the category, so I need to make a tedious process to find the ID.

  Result:

  {module_faq, c., 19227, ajax,}

  Great!

• LR3 does not remember last filter setting

  When you access the image files in the library module, LR3 does not remember filter settings used during the last visit. It was a great feature in 2. Is it possible to restore this desirable behavior?

  It is a post-it.

• Phase Shift Key: Modulation Toolkit

  I am trying to simulate a phase shift key, I have followed an example of OR. the example worked fine and I used the same code but does not work my didi. The number of symbol is not correct.

  I have attached the VI, I could not know what the problem was. The chart of the constellation should remain constant, rather than moving and the number of symbol in the chart must be equal to the symbol on the control.

  Thanks for any help.

  Hello ade77

  Thanks for your post. It seems that your Eb/NO (10 dB) value is not high enough to get the right number of symbols in the right place. Try to increase this number and see if that helps. See the screenshot of your attached code.

  Let us know if this helps!

  See you soon!

  Corby_B

  http://www.NI.com/support

• How to install Adaptive Filter Toolkit on myRIO 1900 RT target

  Hello
  I'm working on the project of Active noise cancellation. I need to collect audio sampling rate of two microphones @40 k and 100 samples per image and audio through speakers @40 sampling rate k of output. For this, I use myRIO 1900 in FPGA high flow personality.
  When I'm designing the circuit Adatptive Filter Toolkit pallets are available in block VI, but when I'm trying to compile the circuit I get the error message saying that
  "LabVIEW: unable to load the shared library AdaptiveFilters n ensure that the library is present on the target of RT." "Either MAX allows you to install software of OR or FTP to transfer custom RT target libraries.

  I went to MAX OR to install the Adaptive Filter Toolkit, NI MAX--> network environment--> myRIO 1900--> software--> software add-on

  I can't find Adaptive Filter Toolkit or the Digital Filter Design Toolkit.

  I seriously doubt the possibility of using Adaptive Filter Toolkit in the FPGA target, but if I create the FPGA VI by default 'personality', Adaptive Filter Toolkit available palettes only not, but if I'm working on the FPGA VI high flow personality, then the pallets Adpative filter Toolkit are available but I can not compile...

  So, my question is how to install Adatptive Filter Toolkit on myRIO 1900 RT target?

  Is it possible to make custom FTP libraries RT target. I can find the Adaptive Filter library but I don't know which folder should transfer (I tried with several files that I can find but its does not work)?

  Please help me

  Thank you

  If your MAX Configuration looks good.

  After this process: NEITHER myRIO 1900--> software--> software add-on

  choose user Defined Installation you should get the view like the Picuture I added before.

  In find it examples explore, you should be able to get see--> toolkits and Modules--> adaptive filters

  Have you already tried to reinstall the Toolkit Digital Filter?

• linking to toolkit modulation AM function generator

  Dear

  I am doing a project in telecom AM modulation demodulation using labview.
  I have attached, the function (such as message signal) generator and modulate Am (as a process of modulation AM) but I am facing problem wiring the function as the message signal generator in the AM modulation. I would be grateful if someone can help me that doing so. In addition, if you have an idea how to make the process of demodulation using the MT modulation toolkit I will be grateful.
  Thank you for your help

  Hi Sir... Peter,

  Thank you for your, you helped me a lot in the resolution of many problems in my project.
  I still need your help for something;

  I did the AM modulation as you fixed, and I added the demodulator block in order to recover the original signal from the message.
  In fact, I am facing two problems:
  1. in the SSB: single side band, I'm not able to recover or demodulate the square wave type.
  2. I am not able to modulate and demodulate a file audio wave.
  I would be grateful if you can help me in carrying out my project.
  Thank you

• installation of the toolkit Modulation

  Hello

  I try to install the Modulation (MT) V4.0 for LV 8.6.1 Toolkit and I'm running the questions with the palette menu. The palette of digital modulation menu does not appear after installation (and not under addons or pallets of rf communication). VI Physics for digital modulation functions are located in the folder program files, but they do not appear in the menu of the palette of LV. Also, when I try to open the files of ments, Labview application lacks Subvi so I'm starting to think that something is really messed up with the installation of the Toolbox.

  For the background, I'm running LV 8.6.1 PDS with measures spectral toolkit (SMT) also installed V2.4. I uninstalled, deleted and reinstalled the SMT and MT directories several times but I still can't the palette menu or the digital modulation VI to work properly. Also, I uninstalled all previous versions of Labview to check that there is no conflict version of Labview. Has anyone else encountered this problem with the modulation toolkit and you know a fix? I would prefer not to have to reinstall all Labview 8.6.1 but if that proves to be the easiest option then I guess I have no choice.

  Thank you

  Tim S.

  Hi Tim,.

  It seems that everything has been installed correctly, so I don't know exactly why this is a not complete automatically. I think we should try to manually add to the palette. I have included a link below that describes this process in more detail, you want to reference part "V. or pallets missing icons. You want to add the digital section to the palette by pointing to the file correct .mnu located in the digital file. I've included a picture where my .mnu as reference file. This should work for you, but please post back and let us know how it goes or if you have any questions.

  Missing icons on the functions or controls in LabVIEW Palette

  http://digital.NI.com/public.nsf/allkb/46E1672AB48C917D86256AFE00075436?OpenDocument

  

• the user's selection by setting the security filter in the ASO to unsort database

  We found a very annoying feature of Essbase: when we make the security filter setting in the ASO database through the console of Regional service, we found that the selection of the user list is not sorted. It is very very difficult to identify the appropriate user name to set the security filter.
  
  All the tips and tricks can improve the process?

  I don't think that this problem is related to ASO - filters are filters.

  All you need to do to sort the column filters is to change the filters, then click on the column heading "name of the filter. It sorts fine in the EE 9.3.1.

  Kind regards

  Cameron Lackpour

• modulation

  Do you have an example of how to downcovert an audio output signal from a modem and then it demodulate in real-time?  Should I connect the audio output of the modem in the port of audio input of the sound card on the computer, right?  And how can I say Labview to read from the audio input port?

  In addition, I don't know how to enter some settings in the Toolbox digital demodulation. I also need to apply a Nyquist filter.  Could you please provide me with an example?

  Here is an example of the modem specification:
  1200 baud
  Central frequency to 1400hz, the pulse width is 1200hz

  How would this information enter the modulation toolkit?  I'm using version 3.0 with labview 8.6 developer edition.

  Thank you

  
  

• Modulation FSK

  Hello eveyone and thank you for this forum

  I'm currently setting up a VI of FSK modulation, and I got stuck so I downloaded the here attached template, but some components were not I wonder where I should get, the missing components are

  * MT generate bits.VI

  * MT generate the parameters.VI system

  * MT modulate FSK.VI

  * MT upconvert baseband.VI

  Thank you

  You need to purchase the LabVIEW modulation toolkit to access these functions.

• Error in compliling the AXF_Custom.pll

  Hello

  while I'm configuration of the EBS with Webcenter adapter I get error at compiling of the file AXF_Custom.pll in Oracle Form Builder Apps Server Machine, below, please suggest.

  identifier of DBMS. XMLDOM. DOMDOCUMENT must be declared.

  

  I'm at the link below to set up the adapter of the EBS.

  http://docs.Oracle.com/CD/E21764_01/doc.1111/e17953/c02_ebs_plugin.htm#ADTAD153

  Thanks in advance

  Hi all

  We can follow the alternative to compile the AXF_CUSTOM.pll file.

  using the command, we can compile the pll file

  $APPL_TOP/au/12.0.0/resource>frmcmp_batch.sh module = AXF_CUSTOM.pll userid = module_type output_file = AXF_CUSTOM.plx apps/apps library compile_all = special =

  For more details follow the 2.2.1 AXF_CUSTOM.pll compilation step using the command below document line

  http://docs.Oracle.com/CD/E29542_01/doc.1111/e17953/c02_ebs_plugin.htm#ADTAD1276

  Thank you

• A particular website comes in the form of text only, no graphics, after I attepted to change a setting while streaming a video clip. IExplore shows the site properly.

  Windows XP. Firefox 3.6.12. Java extensions console, AVG safe search, ADblocker plus, Deputy MS net framework.
  Was watching a video clip on PBS. Full screen. The video menu wouldn't go away. I have a click with the right button on the video screen, changed a setting, in that I think has a filter setting and now I can't get into PBS.org. Iexplore works very well. Uninstall (save all settings) and reinstalling firefox did not work.

  Sounds that you have blocked some content in Adblock Plus. You must click on the ABP icon and check what is blocked on this page.