Motoe3 power is not loaded to

Similar Questions

• Could not load the Norton power Eraser

  Installed Norton Security. Everything works well except a pop up window that says error 5013,3.

  Following the instructions I downloaded Norton Power Eraser. When you are finished, the pop-up with the addon window said I need a newer version of Power Eraser and "click here".

  No mater how many times I try, could not load the new version.

  Don't know what I was doing wrong before, but when the pop-up window came this time it worked.

  I'm glad that it worked, but I wish I knew why.

• I have a MacBook Pro 13 inch early 2015 and when I connect to the power supply the connected is loose and my Mac does not load. Please help me

  MMacBook does not load

  Looks like you have is connected wrong charger (you have an older Mac in the House?) or the charger has been damaged. Perhaps the magnetic head is damaged.

  You have another mac or a friend with a mac that has the same charger if you can try that?

  You can certainly buy replacement chargers, but I recommend that ensure you it is the charger that is the first problem to avoid spending money. If this is a problem with the port on the Mac, then a replacement charger will not help.

  If you don't have a 2nd charger to test, you can take your Mac at the Apple Store or your local electronics store that sells Macs and ask to try the plug one of their display models.

• My iPhone does not load unless the cable is placed just to the right and the phone is still completely. Advice?

  Hey everybody. Since a few days, I have had a hard time charging my iPhone. It all started when my phone onto my computer. He suddenly began to vibrate, and the charging symbol flickered on and outside. Since then, I had to mess with the power cord plugged into the phone until it starts to load. Once it starts to load and remains always completely, is perfectly fresh. The problem is that I do a lot of work and outdoor recreation such as hiking, and I need to charge my phone on the road sometimes. But once I'm start moving the phone around, it does not load until I have reposition it. My phone had not been dropped, smashed, splashed with water, or something serious in several days or even several weeks before acting. This could be a software problem? I cleaned the inside of the charge socket and the charge lead works fine with other devices. I also restored the phone to factory settings and then restore a backup. Any advice would be appreciated.

  Clean the hole of the support and review it with a bright light. You must get it squeaky clean and without bending the rather delicate pins. And make sure that the bent pins.

• IPod Shuffle Gen 2 will not load.

  I pod shuffle 2 generation does not load. Light does not illuminate. May be time for a new or repaired.

  You use the USB cable supplied with the shuffle.  For a 2nd gen shuffle, this cable is long with a cradle for the shuffle.  A cable for 3rd/4th gen shuffle does not work with 2nd gen shuffle (connector is different).

  If you use the right cable, but the random reading light lights at all, the cable may be defective.  There is cable of third party replacements.  If you want to try another cable, make sure it is described as being 2nd generation Shuffle (not 3rd/4th generation).  For example, some are not actually cables

  http://www.Amazon.com/adapter-Apple-iPod-shuffle-generation/DP/B000QHOB4S

  It is also possible that the shuffle is defective.  I think that the shuffle would always turn on when connected to power, if the problem is with the battery.  So it is something else, like a worn or damaged headphone jack.  Or bad logic board.

  Whatever you do, don't forget that a 4th gen new shuffle with a new helmet, docking cable, and the guarantee of one year is $ 49 retail.

• Satellite T110 does not load

  My computer is 3 years old. A month ago, when I turned it on it only showed the THOSHIBA logo and a black on the screen (like its waiting to start, but he used). The assistance Center has guided me to unplug the AC adapter and the battery and wait for some time, reconnect it that.

  It worked and I left the computer until I bought a new battery thinking that was the problem (the old battery was not load more).

  Everything was ok for a few days, since I made sure the new battery will be always full, but yesterday I left it without the power adapter and the battery got completely empty - and now it turns on again.

  Help, please. TNX

  And have you tried to repeat the same procedure recommended by the service agent?
  Remove the battery and the AC adapter / CC, wait a while and then reconnect all parts

  Otherwise I put t think its battery from the laptop problem should also work with the adapter plugged.

• Tecra A11-110 (PTSE1E) does not load

  Hi all

  Recently my laptop stopped charging.
  The battery is new and worked for a while. It works on another laptop.

  When I connect the charger, the laptop gets power, but it does not load. I guess it's always work around.
  Is this a mistake in any sensor motherboard?

  How can I fix?

  Is the motherboard 'dead' (for this purpose)?

  Thanks in advance.
  See you soon,.
  Hugo.

  Have you noticed the problem of load using the old, original battery?
  If the old battery may be charged correctly, I don't think that there is a problem with the laptop.

  You said you have tested this new battery in a laptop.
  Have you tried using another model Tecra A11?

  Your comments would be appreciated.

• Equium P200D - does not load

  I have an Equium P200D who did not pay correctly, I bought a new charger and it worked fine for a while. However I noticed that the laptop has not been held liable. Now the laptop does not load, and even with ac power plugged he won't shoot upward.

  I'm assuming that the battery exceeds the usefulness, but it should not start when plugged into the mains, with battery in or out? So can I assume that support on the laptop is useless?

  any help would be appreciated

  Hi blueknowz,

  > and even with ac power plugged he won't shoot upward.
  This means that the laptop doesn't start over even the AC/DC adapter is connected, right?

  Well, the computer should start even when the AC/DC adapter is connected but the battery is defective. If the battery is not important, you can use Notepad with AC/DC adapter only.

  If the computer laptop doesn t start it looks like a malfunction of the motherboard. It is maybe something wrong with the s load control.
  An accurate diagnosis can be made from an authorized service provider. Do guys say sabout this behavior?

• Satellite Pro A200 does not load if current enforcement

  Hello

  I have a new Toshiba Satellite Pro A200 on Vista. I have a problem with the power adapter and charge socket.
  It will start and run very well and when turned off will charge the battery of fine food. But when running, the machine automatically runs battery, no network and does not load.

  This means that the battery is sinking and ended up to be recharged so just off the coast.
  When the power supply is removed and then reinserted, it will load for maybe 30 seconds, then stops to load again initially and continues to run on battery.
  At the same time, the blue light of indication on the front of the machine lights up to indicate that the ESA is connected and detected, and on battery defiler on windows in States ' ac connected, not charging battery "-in other words it works of ac and is detected but the machine isn't use to run power supply or load unless it is turned off...

  Can anyone offer a solution?

  Thank you

  That s very strange and I guess that this problem could be linked to the hardware problem.
  Either it's a defective battery or there is something wrong with the electronic power supply on the motherboard.
  In my opinion, there is only one way to know what's wrong some diagnostic tests are needed.
  This test can be performed by a technician of the ASP.
  That is why it s advisable to contact an ASP in your country for audits.

  This is a new laptop and warranty should cover everything!

• Recovery DVD does not load

  Hi guys,.

  I use a HP Pavilion A6120N Vista. It has a SATA RAID 0 HD value.  Machine will not start. After ordering the HP Recovery Disk Set, I tried to run the program of recovery.  It displays a message that "Windows loading files...". ». When the progress bar is completed, I get a small bar (2 1/2 inch long) with a few lines on this subject moving from left to right.  Below I have the symbol of copyright and Microsoft Corporation.  But it makes no further along than that.  I put the devices to boot from first and second for the dvd player.  I tried to start with each of them the three DVDs.  I tried to start with disk 1, 30 minute wait and the withdrawal of disc 1 / insert disk two.  I tried booting with the UBCD and another bootable cd and then insert disc 1.  I tried to start with the two disc and pressing F11 I got "Disk Boot Failure, Insert System Disk and press Enter". When I replace it with two disc, I get the same results as above.  Nothing works. If anyone has any ideas, I'm open for them.

  After trying on & more, I got another result.  Without the disc in the drive, if I do not press F11 at startup, I get a choice of starting recovery or start windows normally.  These two choices lead to the small bar mentioned above with the lines moving from left to right. If I press F11, it goes straight to "Windows loading files...". "and the little bar with lines.  I chatted with HP support and they said the 800 number.  They told me that the OS is corrupted which causes the restore disc does not load.  Now, I thought that starting a CD/DVD without going through the operating system.  What's in Vista?  Can he change?  I saw as a warning to the other cd/dvd drive (dvd - rw 16 x pbds dh-16a1L) requires an update of the firmware to recognize the HP recovery discs.  I have the drive HL-DT-STdvdrrw.  Could it have the same problem and it had not just been documented?  So far, I am at a total loss.

  Thank you

  Message edited by TennBlues on 30/12/2008 21:58
  Message edited by TennBlues on 12/31/2008 12:03 AM

  AFAIK boot failure disk means one or both of the drives went bad or BIOS (F10) must be set to zero by default. So if the raid 0 Setup and a defective hard driveis then you need to get out that the hd and run recovery on the drive to work or wait until you get to another replaced.

  No, you do NOT have a corruption of the operating system, and Yes, the recovery disc bypasses the operating system on the drive. Windows Vista disk hard is not effect or prevent recovery disks because the disks will always wipe clean first the drive working.

  Try the following steps.

  (1) reboot the pc and go into F10 for installation (for vista)

  On the MAIN tab, check to make sure that your hard drives are both recognized where says 1st or 2nd disk, etc.

  It should look like WDC, SAMSUNG, ST... etc.

  (a) if it is not in the list, then check the SATA cable and power cables inside your computer to make sure it is plugged both ends properly and reconnect the cables to the two discs.

  (b) if only 1 disk is listed, then the other one may went bad on you and I would be the wrong drive breaker go back into the BIOS F10 menu and check that the right drive appears under you devices.

  I would then run a recovery disk of 1 until you replace it. In this case you will not have a raid 0 configuration more since she was only 1 player used.

  (2) try also reset the BIOS default settings by going to the menu of the BIOS F10 at startup and press F5, then press Yes then enter then F10, then Yes, then enter to restore the default BIOS settings.

  (3) after the reboot back to the BIOS menu and go right on the Startup tab and choose boot DEVICE PRIORITY and set the 1st boot device to the Group of HARD drive, then save the changes and exit the BIOS.

  If you want that you set the CDROM boot first yo group.

  You can also turn on the pc and press ESC to boot from the hard drive or a disk drive group.

  I recommend first resetting the default BIOS settings and check the devices first, before opening the pc.

  Message edited by c0rnel on 12/31/2008 01:42

• Satellite L655 does not load

  Hello

  My satellite L655 does not load, BUT it works fine when I charge the battery of my second toshiba laptop
  also does not open when I plug just the charger without the battery (led power 3min.from-no at all)

  charger works fine
  battery works very well
  tested on my other toshiba

  It works when I plug a charged battery ready.

  Any guys help?

  > It doesn't work when I plug a charged battery ready.

  It seems that there is a problem with electronic control gear.
  I mean that the laptop does not work even if plugged into the sector.
  It is certainly a problem given that all laptops would work without battery connected but connected to the power outlet.

  So I think there is a problem with the electronics which is part of the main map.

• Windows 7 does not load on the laptop. Satellite L series

  Not sure what happened all of a sudden with my laptop, but it does not load windows. This is the error msg I get:

  Intel UNDI, PXE - 2.0 (build 083)
  Copyright (C) 1997-2000 Intel Corporation

  For Atheros PCIE Ethernet Controller v2.0.0.9 (15/12/09)

  Check the connection of the cable!
  PXE - M0F; Exit Intel PXE ROM.
  No boot device - insert boot disk and press any key

  I tried using the recovery disk for the repair of the system and using the sfc/SCANNOW utility, but both just run it for hours (12) and not going anywhere.

  I tried reinstalling the RAM and nothing.

  Help, please!

  Liz

  Post edited by: lizandcourtney

  1. enter in BIOS
  2. restore default values
  3. exit & save changes

  Youre system should boot in AHCI now again. If you get the same message:

  1. enter in BIOS
  2. go in advanced
  3 set mode Compatible HARD drive / IDE
  4. exit & save changes

  To enter the BIOS F2 press until you initialize (directly after pressing the power key press F2 continiously).

• A friend gave me his iPad 5.1.1 iOS.  I plugged on my desktop to load (I have also 2 iPod Touch from my iTunes library), but the iPad indicates there is no SIMcard (?) and that it does not load.  That pasa?

  A friend gave me his iPad 5.1.1 iOS.  I plugged on my desktop to load (I have also 2 iPod Touch from my iTunes library), but the iPad indicates there is no SIMcard (?) and that it does not load.  That pasa?

  The iPad does not have a SIM card. Most are wifi only.  The USB jack on the side of a machine very likely does not provide enough current to recharge an iPad. Use the power supply provided 2.1 watts (if you have one - if it isn't get a).

• MacBook Pro is super slow since yesterday and does not load now

  I went to use my MacBook yesterday and it was to be extremely slow and after hard resetting (by pressing the power button) about three times, it was fine. Now today, I turned on my MacBook and now the progress bar will only about 60-70% of the way and then stay stuck there. I restarted once and it was still stuck. I restarted once more go in safe mode, but it was not completely load again. I found another discussion about a person having a similar problem and I have reset the NVRAM and still it will not load.

  sounds to me like your HD is a failure...

  You have a clone of external start to test?

• Can not load my iPhone after the last update

  Just downloaded latest updates on iPhone 5 and now the phone will not load... someone else live the same.

  I checked all connections and the son... all good.

  Hello Linda,.

  It seems that your phone does not load at the moment. I would use this section of the following article to help you solve this problem:

  Recharge your iPhone, iPad and iPod touch

  If your device doesn't load or loads slowly

  If you have very low battery and you plug in the power, a black screen or with a red battery may appear for a few minutes. Charge your device for half an hour. If it still doesn't load, follow these steps:

  1. Remove all debris from the charge on the bottom of your device socket, then firmly plug your cable to charge your device. If the port of loading is damaged, your device probably need service.
     
  2. To a power outlet wall, search for closed connections between your charge cable, USB adapter and outlet or try another outlet. For a computer, verify that it is not in mode 'sleep', then try every USB port on the computer.
  3. Restart your iOS device. If your device does not illuminate or still does not, know what to do.

  * If you are not sure if an accessory is damaged, take it to an Apple Store or the provider of services authorized Apple for evaluation or Contact the Apple Support.

  Thank you for using communities of Apple Support.