Mouse not removed and Trun off the power when you watchig film


I found the solution... just open up laptop and change the slick carpet mouse that's all

Tags: Notebooks

Similar Questions

  • Is there a need or a way to turn the pencil off the power when you do not use?

    Is there a need or a way to turn the pencil off the power when you do not use?

    Unfortunately not. The best thing is to turn off bluetooth. However, you will need to re - pair the iPad and the pencil again by plugging in the port of lightning. When not used the pencil of apple do not lose a lot of power.

  • Saving ink by powering off the power when you are not using it?

    I have a HP Officjet 6700 running under Windows 7 64-bit and read that turning off your printer when you don't use to save on ink. Is this true?

    Hello

    Right, but turn off will save a bit of power. Inkjet printers need ink more when you turn very often.

    I hope this helps.

  • Satellite M30X powers off the power when you touch the USB port

    Hello everyone, just registered and it is the first problem:
    As there is no general hardware forum, I post my problem here.

    I got it twice, my laptop
    (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

    Motherboard:

    NorthBridge: Intel i855GME
    SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
    Motherboard model: Toshiba EAL20

    USB:

    82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
    Version: 1.0
    Interface: UHCI
    Frequency: 48 MHz

    82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
    Version: 2.0
    Interface: EHCI

    I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

    Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
    There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

    Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
    I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
    Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

    What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
    Still works well. Now for me, that I broke the USB port Insider somehing.
    I could not determine also the loose parts or unfirm at all.

    Y at - it there, diagnostic software that measures the motto of the port or power problems?
    I have a multimeter, fetch short-circuits with it?

    I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

    Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

    Fabian

    Hello

    I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

    > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

    I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

    However, what we can do is to provide some suggestions and assumptions
    It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

  • Satellite 2435 powers off the power when you try to install the recovery CD of OS

    Happy new year

    Satellite 2435 powers off accidentally when trying to install the operating system from disk with Windows XP Pro startup disk or recovery.

    When starting and working with Winternals AdminPak 5.0, Portable Edition Windows or Dos 6.22 it works stable.
    When booting with the disk recovery he died each time in a different position - when partition formatting, copying the files, etc..

    Hardware problems, isn't? And is it possible to determine and solve the problem at home (because we now hoildays, services does not work)?

    Thank you in advance.

    (Sorry I don't speak English very well)

    When I had my old computer I encountered similar problems in Windows XP and the Windows XP installation. There is a WinXP option to disable the auto-restarting after a problem, instead of restarting, a blue screen stating that the problem appeared. I lived during the installation of WinXP blue screens every time at various times as you and your power off, he appeared on the different WinXP CD (without SP, SP2 with nlite, etc.).

    Maybe your "power off" is hidden blue screen too, but I'm not sure. If this is the case, it may be a hardware problem, so you should test your RAM, your drive hard, etc., for example using memtest for your RAM and the built-in WinXP 'chkdsk '.

    It's probably hardware problems. Were you ever able to correctly use the disk without problem in the past, or is this the first time you try to use the recovery disk?

  • Tecra S2 began to turn off the power when you run some heavy applications

    I have laptop Tecra S2 and (almost 3 years) had no problem so far.

    Recently, it started to turn off instantly when you run some heavy duty applications, such as games. He takes turns instantly and can work hours if it's just a spreadsheet or just Web broswing documents but when I start a game it takes 15-20 minutes.

    Once I started it even once, it takes less time to get the same result.

    My guess is overheating - any ideas how to fix?
    Or it may be something different?

    See you soon

    Hello

    There is nothing to fix. The laptop needs to be cleaned. It must be done on the professional track. This means that the laptop must be disassembled as just at the moment when the cover is removed the cooling fan and the cooling rack can be cleaned properly.

    After having this laptop will work like new.

  • laptop computer closed off the power when you unplug

    Original title: laptop turns off

    I just replaced my battery because my only original suggested I do. Now, when I unplug my laptop with the new battery in, my computer turns off. I checked the BIOS system set in place and my adapter shows she is good, fully charged battery display and works normally. Why did the computer turn off?

    Hello

    What is the number and the model of the computer?

    It is made from material that I would say you to the manufacturer of the contact system to solve the problem.

  • flashes and turns off the video when you play, has sound

    Where to play games online TI juice flashes. I have sound but no video. This also happens when I watch QVC on my computer.

    Hi yesndeed70,

    ·         What version of the operating system is installed on the computer?

    ·         You use Internet Explorer? If so, what version are you using?

    ·         You get the error message?

    Follow these methods.

    Method 1: If you are using Internet Explorer, follow the steps in the article.

    The problems of games online using Internet Explorer

    http://support.Microsoft.com/kb/2528246

    Method 2: To update the drivers to display/graphics.

    Updated a hardware driver that is not working properly

    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

    For reference:

    The problems of the game performance

    http://Windows.Microsoft.com/en-us/Windows7/fixing-game-performance-problems

  • Satellite C660 powers, black screen and switches off the power

    Hello world.

    I have a C660 - 22v.Everything worked very well. An hour later, then to use the laptop again, it works, and he turned on as normal in 2 clicks, then more nothing. Just a black screen, not yet turned on, then after 5 to 15 seconds, the fan accelerates for a second or 2, then the laptop turns off.

    Tried with the batteryout & just the charger pluged, just the battery, hold the power button, all sorts of ways, but it only of the switches off the power.

    I think that the hard drive has failed. Any help would be welcome as its out of warranty (16 months).

    A big thank you in advance, Neil.

    In my opinion it has nothing to do with the hard drive. I assume that there is a problem of electronic power supply. I have a similar problem with my A300 and at the moment I put t know what to do.
    Repair is probably quite expensive so I m thinking about selling on eBay as being faulty.

    Problem is that we cannot do much. What should do? You can dismount, take a look inside and put the new.

    Either it works or not. I'm afraid that your problem is for the service and it must be checked by the guys from the services of m.

  • Cisco router WIFI does not work after turning off the power

    I have a CISCO router that worked very well until someone turned off the power for a few minutes.  I tried to unplug the modem, the router and the laptop and waited a bit.  Then I turned on the modem, then the router, then my laptop but it is still not in communication with the modem.  I can use the modem with a hard connection to the laptop but need the WiFi as well as others can use it.  Help, please.

    You need to contact support with your Cisco router.  It looks like it might have been reset and the installation needs again.

  • A lot of questions on how stop and turn off the power of the computer for Windows 8 without having to use the own compiuters out button?

    I have seen a lot of questions on how do I turn off Windows 8 and stop computer but no answers?

    I use CTRL, ALT & DEL, and then click the below icon to the right, there are then 3 choices, sleep, stop, or restart.

    Is there an easier way?

    8 win there a way. 1. move the cursor to the top right of the screen

    2. click on settings

    3 be able to click at the bottom of the screen

    4. choose: sleep, Shut Down, or update and reboot

    This isn't my idea, but someone sent me.

  • End of Cup Video Clip off the power when send you first Pro CC 2014 to effects after 2014 CC and I slowed down with Timewarp?

    When I send a clip from Premiere Pro CC 2014 to after effects CC 2014 and I slowed down with Time warp the clip cut of 75% at the end of the video and display only the first 25% slow.  How can I fix this and how I round it travels in first pro to play the FULL slow motion video clip?

    Try adding effect temporal Deformation on an adjustment layer in AFX, rather than on the video it self.

  • Bo off the power when save you in Keynote 7

    I use Keynote to constitute a group of slides synchronized to a soundtrack that plays on the group.  The time for each slide is not exactly the same thing.  In Keynote 6.6 and previous versions, I joined the soundtrack, then folder mode advanced blades as needed.  To do this I need to hear the soundtrack when recording (mike is off) the time to advance each slide.  It worked well until Keynote 7 I have discover that the soundtrack is disabled in record mode.  It's actually record, but I can not hear in record mode (only when the recorded session is read).  It's silly that I need to hear the soundtrack to know when to move to the slide.

    It doesn't seem to be a matter of Keynote7, because when I removed 7 Keynote and replaced with Keynote 6.6 everything worked as I expected.  In other words, I could hear the soundtrack in record mode.

    I have macOS Sierra and use a MacPro (end 2013) or MacBook.

    Has anyone found if it is possible to hear the soundtrack in record mode in Keynote 7 (with microphone mute or, indeed, using the microphone on the soundtrack).  If yes have you had to adjust anything in the 7 Keynote circles to hear the soundtrack in record mode?

    There are a number of things, is not the case in Keynote 7 that were available in previous versions.

    Its never a good idea to use an application in a version of point zero (e.g. 7.0) for production activities, use it to test only. Keynote version 6.6.2 works as expected in the Sierra, so that install from a backup file.

  • E320 unexpectedly powers off the power when change you position!

    Hey guys,.
    Is not my ThinkPad Edge E320 but a few months old, but I've noticed a problem with it. I would like to know if others are facing similar problems and if there is no solution for it.

    The laptop shuts off completely when I move. But I noticed that it doesn't happen if I'm REALLY careful with it and move it into both sides.

    It seems to be a 'soft spot' on the underside of the laptop that forced him to cut immediately when it is pressed. And move the laptop holding down causes exactly that.

    Is anyone else facing such a question? It would be great if someone could help me with this.
    E320 no users, if you have an idea about what is happening and that you may know a solution, please do not hesitate to post on this.

    Thank you everyone.

    I found a solution that seems a permanent solution to this problem.

    Download the two photos FYI
    http://S21.postimg.org/mxsbtwrmv/PHOTO2.jpg
    http://S21.postimg.org/fgnpsfrhj/Photo6.jpg

    I bought the E320 for a year. Never had a problem during my study of honours. That from last week, when moving the laptop, the machine stopped immediately offshore. After some troubleshooting (plug battery and AC power), I noticed that the problem occur only when you press and hold the bottom of the left upper keyboard with pressure.

    Google this question, found a large amount of complaints from the forum of Lenovo and bath tub. Thanks to the entrance of ThunderDuck whirlpool. I just put a thick paper (I chose the photo paper) underneath the SSD (metallic surface caused the short circuit, I guess) and the problem has been corrected.

  • Satellite P300 - randomly turns off the power when connected to the external monitor

    Hello

    I have a Satellite P300, Intel Core 2 Duo T9400 2.53 GHz, 4 GB RAM, ATI Mobility Radeon HD 3650 512 MB, running Windows 7 ultimate x 64.

    Recently, I bought an AOC v22 led screen and connect my conputer via HDMI. Everything works fine, but sometimes my computer off just randomly. I might have something to do with my computer overheating, so I clean the fan, but this was not good.

    I think it has something to do with the LED screen because my computer was never off his own.

    Hello

    So this also happens if you n t connect laptop to external display? So, you can determine what is causing this problem.

    If the computer laptop doesn t turn off without external monitor, you should try to update the BIOS and the display driver. Two updates that you can find on the Toshiba site:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

    You close the lid if you have connected the external monitor?
    What operating system do you use?

    In addition, it would be interesting to know how you clean the laptop. That's why I use the jet of compressed air that can blow the dust from the cooling fans and you don't have to disassemble the laptop.

    Good bye

Maybe you are looking for

  • iPhone 1 (first generation) Sim Card tray

    Anyone know a source for the purchase of an an iPhone SIM card Tray 1 (first generation)? I have mine since 2007. My wife is an educator specialized and I would use the phone like an iPod Touch, basically. I have to get the iPhone enabled in order to

  • I don't have a toolbar in Outlook Express e-mails.

    Because I do not have a toolbar I can not send or forward emails.  I have Windows XP.  Also, I can't delete the deleted emails or unwanted emails. [Moved from comments]

  • BlackBerry Smartphones SMS - 1?... .Please help!

    Help, please! When I have no new messages in my Inbox SMS, it is said - 1 on the home screen, rather than simply say 'messages' as he usually does.  So when I get a message, he said 'messages' instead of '1', and when I have 2 messages in my Inbox, i

  • Backup on external hard drive Iomega problems

    Dear all I got an email notification that it has been an answer to my original question, but couldn't find it on the forum. First time user! Here's the info so I have asked me to help solve my problem. 1. the model number of the drive is external har

  • Local test run of Viewplanner, AutoIt error failed 'error in the expression' command-line viewplanner.exe 11256

    HelloAfter a few fights, I managed to have the test run to start in a local race, however, after some time AitoIt script crashes with "error: error in the expression ' (see attached screenshot). After a while the workload gets killed as indicated on