Multifunction color HP LaserJet Pro 200: I can't print to my HP printer using wifi, it was working and stopped after the electricity blackout

Similar Questions

• Multifunction color HP LaserJet Pro 200: HP LaserJet Pro 200 color MFP M276nw on El Capitan: Scan does not

  Since my upgrade to El Capitan my USB connected HP LaserJet Pro 200 M276nw MFP color analysis no more.

  What I've tried so far:

  Installed the latest drivers > unsuccessfully

  Tried all the solutions suggested here: http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-LaserJet-Pro-200-color-MFP-M276nw-Scanni... > no success

  Have any suggestions what to do next?

  Update: the solution provided in this thread solved my problems:

  http://h30434.www3.HP.com/T5/Mac-printing-and-scanning/HP-LaserJet-2300-not-working-with-El-Capitan/m-p/5281267/highlight/true#M61077

   

• Multifunction color HP LaserJet Pro 200: problem error 79

  HP LaserJet Pro 200 color MFP M276nw that has error 79 when the woman made an impression. I downloaded the firmwear date, but is not complete installation eventhough the poster 100% progress. Print has only 400 pages printed since new. Need help

  You must click on the link below and download the firmware update file and then run it and follow the instructions.  It is usually sufficient to tell the app what printer to update and it does from there.  Takes only a few minutes.

  http://support.HP.com/us-en/drivers/selfservice/HP-LaserJet-Pro-200-color-MFP-M276/5097648/model/5097653#Z7_3054ICK0K8UDA0AQC11TA930O2

• Multifunction color HP LaserJet Pro 200: Scan problem tray

  I'm having a problem with the scan on the all in one tray. Basically I never scan A4 paper (wireless), but once the data transmitted from the printer to the pc, I find that the PDF version on the screen is too long. I then have to manually crop the size down to A4. It might not seem that a huge problem when say you scan one or two pages, but when you have a whole pile of documents to download, cropping manually each size takes a lot of time. The scanner never used to do this, it's past numbers. I'm using the wrong settings or y at - it something wrong with the scanner itself?

  Well, this should solve your problem:

  Make sure that the printer is plugged directly into a wall outlet, not a surge protector.

  1. Open HP Scan.
  2. Click on the gear icon.
  3. Click on the harvest.
  4. Select A4.

  Please let me know the results after following the above. If you can properly analyze, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Multifunction color HP LaserJet Pro 200: color HP LaserJet MFP M276nw 200 Pro analyzes issues with the new driver (Oct 2015) and El Capitan

  When I updated to the latest HP driver from the HP Support/drivers page, my MFP stopped scan from either a wireless network or directly connected setting.  It seems that if I scan the bed itself, I can scan when the print/scanning felt connected to my Mac, but the real problem is the document feeder.

  I also updated all THE updates Apple, including the HP Easy Scan application.

  When using the document feeder, the process initiated as it should... the first page scans, but does not appear in the HP scanning software... then 10 minutes later, the second page scan (same not result... no picture)... can I get a document could not load the error or something.  When this happens... I can't try to scan anything more until I have restart the MAC and printer.

  Hi @epbarnett70,

  I got a few comments on this issue. Please download and install the HP Easy Scan application to see if it will allow you to scan from the ADF. Use the app for Easy Scan HP.

  HP Easy Scan

• Multifunction color HP LaserJet Pro 200: printer HP LaserJet bleeding in the pages

  Well, so a few months ago our printer started printing with strange faded color smear on the pages. Very subtle at first, but it has progressively worsened over the months, and now it covers almost the page:

  http://i655.Photobucket.com/albums/uu275/zzzz4444/HP.jpg

  It is magenta on one side of the page and orange-ish on the other. I tried to manually run a Page several times cleaning, cleaning things, replacement of cartridges, replacing the transfer roller, and calibrate the color cartridges, which none shows any significant improvement. Does it also on the print side of the paper, and it seems that the toner is leaking on the transfer roller mainly (on the edges, but also on the rest of the roll).

  Any ideas/suggestions?

  It seems that as faulty toner cartridges, are you using the new HP cartridges?

• Multifunction color HP LaserJet Pro 200: printing problems - Full black pages!

  My printer has suddenly started printing totally black pages - new black toner cartridge a month ago.

  Do you still have the old toner cartridge. It could be the toner so if you can try another good cartridge. I also have to remove and reinstall the black toner cartridge.

• Color HP LaserJet Pro 200 M252: clearing the jammed paper

  Printed paper is stuck between the back door of the printer and the output area and is not reachable to clear for further printing.   I can't access this area.  How can it be erased successfully.

  Hi @trevorat10 ,

  By your post, I see that you have a paper jam from the rear door of the printer and the output area. Want to know how to remove it. I want to help you solve this problem.

  I'm sorry, but I can't find a color HP LaserJet Pro 200 M252.

  When the printer was purchased?

  You may color HP LaserJet Pro 200 M251 model?

  Please call our technical support at 800-474-6836 if the printer is still under warranty for assistance. If you do not live in the United States / Canada region, please click the link below to get help from your region number.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Have a great day!
  Thank you.

• the Laserjet Pro 200 MFP can print on 110 lb card stock?

  The all-in-one Color Laserjet Pro 200 can print on card stock 110lb?

  Hello

  The following specifications matrix info shows:

  http://WWW8.HP.com/au/en/products/printers/product-detail.html?OID=5097655#! tab = specifications

  Weight, supported

  60 to 163 g/m² (up to 220 g/m² with HP laser glossy photo papers)

  Recommended media weight

  60 to 90 g/m²

  With the help of the following conversion

  http://okpaper.com/calculators/lbs-to-GSM

  110 lb = 162.8 g/m² or 163 g/m²

  This can work, a bit tie, no room for error.

  Kind regards.

• Color HP Laserjet Pro 200 M251n does not in Sleep Mode

  Printer: HP color Laserjet Pro 200 M251n

  Firmware: 2014-06-04, Version 20140521

  Problem:

  Since the last update Firmware the printer does not sleep/wake no event (all configured to wake up the printer) will wake up the printer. Even to connect via Webinterfac the printer does not respond. Ping also fails.

  Tried to connect the printer to the printer ports / wall plug changed network cables nothing worked.

  The only solution is to reset the printer (power off / on) to get the printer working again.

  Played a bit with the EcoSmart configuration, but little matter what is selected it its always the same as the printer stuck sleep/sleep mode and don't responde.

  Y at - it somewhere the old FIrmware to download to try a downgrade if it would help?

  I really don't think there is anythink else I could try.

  just to confirm that the last Firmware update solves the problem

  If I remember correctly it when, one day in December when it came out

• Color HP Laserjet Pro 200 M251: HP Laserjet Pro 200 M251nw print pdf with OffBeat foot

  Printing documents PFD with the quirky footer al the way to the top.

  Print the pdf as image only pages, then the foot rest where it belongs.

  Hi @Martinkoopman,

  Welcome to the Forums of HP Support! I see when you print pdf documents to your HP LaserJet Pro M251nw Color it prints with the footer moved all the way to the top.  If you print as an image only it remains where it requires.

  1. what program you are using to print PDF files from?

  2 have you tried to update the program?

  3. this happens in all programs or just one?

  I would like to run you HP print and scan doctor > www.hp.com/go/tools- it was designed by HP to offer users troubleshooting and characteristics of fix needed to solve many common problems experienced with HP print and scan the products related to Windows computers.

  What are the results? I'll watch for your reply.

  Thank you for being a part of the community of HP. Please let me know if this helps solve the problem by marking this message as "accept as Solution". If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say thanks for my effort to help, click on the "Thumbs up" to give me a "Bravo".

• Color HP LaserJet Pro 200 printer M251n Imaging drum

  I am about to enter the market for color laser printer and reflected on the CP1025 in option, but I'm leaning toward the M251n.

  It is purely for domestic use - no commercial!

  My curiosity is the imaging drum?

  for the CP1025 replacement is offered life - 15000 copies (Ithink)

  Can't seem to find a reference for the M251n

  What is the estimated life of the Imaging for the M251n drum?

  Is there a replacement drum?

  Are there other partners of parts - for example the belts to replace?

  I note that the cartridges supplied in the box are of limited life (700 prints)

  The drum also has similar "capacity/life shortened.

  Hello user-retirement,

  Please find below the answers to your questions. I was able to gather most of the information.

  1 > what is the estimated life of the Imaging for the M251n drum?
  see the cyclical report in print specifications, which is 30,000 pages per month. for CP1025, the duty cycle is 15000 per month.
   http://support.HP.com/us-en/document/c03315004

  2 > is there a replacement drum?
  Yes, but the drum is an integral part of the Toner Cartridge.

  3 > y at - it other associates of parts - for example of the belts to replace?
  I don't think so. Contact HP Support.

  4 > I see that the cartridges supplied in the box are of limited life (700 prints)
  Yes, the page yield is 700 because they are introductory toner cartridges.

  5 > the drum has also similar "ability/shortened life":
  Drum life lasts the life of the Toner Cartridge. The drum is an integral part of the cartridge.

• LaserJet 400 ColorMFP M475dw: Problem of power cord for m745dw multifunction color HP LaserJet Pro 400

  I'm trying to find the number of pieces of the electric cable.

  My warranty expired on 6 December 2014.

  My power cable is flaky.

  When I move a bit the the line cord with the output plug, my printer would turn off and turn on again.

  If I move the power cord a little by the power printer connection, power remains standing.

  Can anyone provide me with the part number of HP for the power cable?

  Thank you

  Yucaipa

  This printer uses a standard pc power cord.  All power cord printer or standard pc with 3 connections will work fine.  I just hope that it is the power supply cord and not taking on the printer.

• Color LaserJet Pro 200 M251nw: color HP Laserjet Pro 200 M251nw prints no fonts more than 48 using Office WORD 2013

  If create a new Word document and I type the letters police 72, the letters do not print. If the font size is reduced to 48 it then prints. The new printer is connected to my laptop via USB. I use a HP laptop Pro 7420 s, 32-bit with MS Office H & B 2013. Any ideas as to what I need to check? Thank you.

  Thank you very much, Provost. Please send me the links, which makes it very easy for me. Upgrade to the latest firmware fixed the problem immediately. Accepted solution.

• Multifunction color HP LaserJet Pro CM1415fnw - notice of incoming call

  I use the above multifunction device on a network with Windows 7 (and Vista) machines and Mac OS X Lion (v10.7.2).  For some reason, the main screen constantly displays the message 'call '.  It is connected to an incoming phone line (downstream from a Vonage Linksys router, so I use IOPV), and there is an exit of a Panasonic KX - TG6441 phone without phone/answering machine phone line.

  Is it normal that the screen displays 'Incoming call' with the key 'Start Fax' down right under the screen stardard of?

  Thank you for all the advice!

  You can configure this value higher.  The minimum standard ring of Bellcore is 40 volts, typical is from 70 to 90 volts RMS.  I would like to try 40 and 50.  Make sure that it does not always meet the rings.  If you have a voltmeter and adapter in small groups, you can measure the voltage of ringing to see what is generated.