Multifunction color HP LaserJet Pro 200: problem error 79

Similar Questions

• Multifunction color HP LaserJet Pro 200: HP LaserJet Pro 200 color MFP M276nw on El Capitan: Scan does not

  Since my upgrade to El Capitan my USB connected HP LaserJet Pro 200 M276nw MFP color analysis no more.

  What I've tried so far:

  Installed the latest drivers > unsuccessfully

  Tried all the solutions suggested here: http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-LaserJet-Pro-200-color-MFP-M276nw-Scanni... > no success

  Have any suggestions what to do next?

  Update: the solution provided in this thread solved my problems:

  http://h30434.www3.HP.com/T5/Mac-printing-and-scanning/HP-LaserJet-2300-not-working-with-El-Capitan/m-p/5281267/highlight/true#M61077

   

• Multifunction color HP LaserJet Pro 200: Scan problem tray

  I'm having a problem with the scan on the all in one tray. Basically I never scan A4 paper (wireless), but once the data transmitted from the printer to the pc, I find that the PDF version on the screen is too long. I then have to manually crop the size down to A4. It might not seem that a huge problem when say you scan one or two pages, but when you have a whole pile of documents to download, cropping manually each size takes a lot of time. The scanner never used to do this, it's past numbers. I'm using the wrong settings or y at - it something wrong with the scanner itself?

  Well, this should solve your problem:

  Make sure that the printer is plugged directly into a wall outlet, not a surge protector.

  1. Open HP Scan.
  2. Click on the gear icon.
  3. Click on the harvest.
  4. Select A4.

  Please let me know the results after following the above. If you can properly analyze, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Multifunction color HP LaserJet Pro 200: printing problems - Full black pages!

  My printer has suddenly started printing totally black pages - new black toner cartridge a month ago.

  Do you still have the old toner cartridge. It could be the toner so if you can try another good cartridge. I also have to remove and reinstall the black toner cartridge.

• Multifunction color HP LaserJet Pro 200: color HP LaserJet MFP M276nw 200 Pro analyzes issues with the new driver (Oct 2015) and El Capitan

  When I updated to the latest HP driver from the HP Support/drivers page, my MFP stopped scan from either a wireless network or directly connected setting.  It seems that if I scan the bed itself, I can scan when the print/scanning felt connected to my Mac, but the real problem is the document feeder.

  I also updated all THE updates Apple, including the HP Easy Scan application.

  When using the document feeder, the process initiated as it should... the first page scans, but does not appear in the HP scanning software... then 10 minutes later, the second page scan (same not result... no picture)... can I get a document could not load the error or something.  When this happens... I can't try to scan anything more until I have restart the MAC and printer.

  Hi @epbarnett70,

  I got a few comments on this issue. Please download and install the HP Easy Scan application to see if it will allow you to scan from the ADF. Use the app for Easy Scan HP.

  HP Easy Scan

• Multifunction color HP LaserJet Pro 200: printer HP LaserJet bleeding in the pages

  Well, so a few months ago our printer started printing with strange faded color smear on the pages. Very subtle at first, but it has progressively worsened over the months, and now it covers almost the page:

  http://i655.Photobucket.com/albums/uu275/zzzz4444/HP.jpg

  It is magenta on one side of the page and orange-ish on the other. I tried to manually run a Page several times cleaning, cleaning things, replacement of cartridges, replacing the transfer roller, and calibrate the color cartridges, which none shows any significant improvement. Does it also on the print side of the paper, and it seems that the toner is leaking on the transfer roller mainly (on the edges, but also on the rest of the roll).

  Any ideas/suggestions?

  It seems that as faulty toner cartridges, are you using the new HP cartridges?

• Multifunction color HP LaserJet Pro 200: I can't print to my HP printer using wifi, it was working and stopped after the electricity blackout

  I got my printer to print via wifi and it was working fine but as the power went out a few seconds this morning, it will not be printed.  I even reset the wifi but does not always print.

  Well, for this issue:

  1. Make sure that the printer is plugged directly into a wall outlet, not a surge protector.
  2. Turn the printer off.
  3. While the printer is turned off, disconnect the power cable from the back of the router for a minute.
  4. When the lights come back on the router, turn on the printer.

  Now, on the printer, click on the wireless icon that looks like a radio tower. If you see a line indicating the status: not connected, click on settings and Wireless Setup Wizard to connect the printer to your network.

  Finally:

  1. Click on start and open devices and printers.
  2. Right-click on any icon of your printer listed.
  3. Click on remove the instrument.
  4. Click Add printer, and follow the prompts to add a new queue for your PC.

  Please let me know the results after following the above. If you are able to print, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Color HP LaserJet Pro 200 M252: clearing the jammed paper

  Printed paper is stuck between the back door of the printer and the output area and is not reachable to clear for further printing.   I can't access this area.  How can it be erased successfully.

  Hi @trevorat10 ,

  By your post, I see that you have a paper jam from the rear door of the printer and the output area. Want to know how to remove it. I want to help you solve this problem.

  I'm sorry, but I can't find a color HP LaserJet Pro 200 M252.

  When the printer was purchased?

  You may color HP LaserJet Pro 200 M251 model?

  Please call our technical support at 800-474-6836 if the printer is still under warranty for assistance. If you do not live in the United States / Canada region, please click the link below to get help from your region number.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Have a great day!
  Thank you.

• LaserJet Pro M276nw: M276nw LaserJet Pro 200 connection error / update Firmware

  I'm trying to update my firmware on my printer wireless.  The current Firmware Datecode is 20121026.  I have run the wireless network Test report and the summary network and it shows the printer connected and on the correct home network.  I have no problem printing, however, when I go to Check for Updates I get the following message:

  Connection error

  The printer cannot connect to the service.  Check the Internet connection.

  Any suggestions?  Thanks in advance.

  OK, you got it the second time. Not all of the SAP is unified in the layout. It is more difficult to stay on top, but you found it. Ok. Always make the mistake so. This is not good.

  Looks like the printer is blocked. You have reset the network?

  Turn the printer off and unplug the router for a minute. Then when the network has restored himself to try to update the firmware again.

  You may need to update the firmware via a USB connection. This link will take you to the page of software and the printer driver. Software and pilot results for: HP LaserJet Pro 200 color MFP M276nw.

• Color HP Laserjet Pro 200 M251n does not in Sleep Mode

  Printer: HP color Laserjet Pro 200 M251n

  Firmware: 2014-06-04, Version 20140521

  Problem:

  Since the last update Firmware the printer does not sleep/wake no event (all configured to wake up the printer) will wake up the printer. Even to connect via Webinterfac the printer does not respond. Ping also fails.

  Tried to connect the printer to the printer ports / wall plug changed network cables nothing worked.

  The only solution is to reset the printer (power off / on) to get the printer working again.

  Played a bit with the EcoSmart configuration, but little matter what is selected it its always the same as the printer stuck sleep/sleep mode and don't responde.

  Y at - it somewhere the old FIrmware to download to try a downgrade if it would help?

  I really don't think there is anythink else I could try.

  just to confirm that the last Firmware update solves the problem

  If I remember correctly it when, one day in December when it came out

• Color HP Laserjet Pro 200 M251: HP Laserjet Pro 200 M251nw print pdf with OffBeat foot

  Printing documents PFD with the quirky footer al the way to the top.

  Print the pdf as image only pages, then the foot rest where it belongs.

  Hi @Martinkoopman,

  Welcome to the Forums of HP Support! I see when you print pdf documents to your HP LaserJet Pro M251nw Color it prints with the footer moved all the way to the top.  If you print as an image only it remains where it requires.

  1. what program you are using to print PDF files from?

  2 have you tried to update the program?

  3. this happens in all programs or just one?

  I would like to run you HP print and scan doctor > www.hp.com/go/tools- it was designed by HP to offer users troubleshooting and characteristics of fix needed to solve many common problems experienced with HP print and scan the products related to Windows computers.

  What are the results? I'll watch for your reply.

  Thank you for being a part of the community of HP. Please let me know if this helps solve the problem by marking this message as "accept as Solution". If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say thanks for my effort to help, click on the "Thumbs up" to give me a "Bravo".

• M475dw multifunction color HP Laserjet Pro 400 - 49 Service error

  I get the error "49 service error" when printing any PDF from adobe acrobat reader document is DC

  If I print the same document from the same network share on the same printer using the player of acrober (no), it prints very well. Go figure.

  PDF is adobe.  First thing would be to update the firmware of the printer or change the PostScript driver from adobe.

• LaserJet 400 ColorMFP M475dw: Problem of power cord for m745dw multifunction color HP LaserJet Pro 400

  I'm trying to find the number of pieces of the electric cable.

  My warranty expired on 6 December 2014.

  My power cable is flaky.

  When I move a bit the the line cord with the output plug, my printer would turn off and turn on again.

  If I move the power cord a little by the power printer connection, power remains standing.

  Can anyone provide me with the part number of HP for the power cable?

  Thank you

  Yucaipa

  This printer uses a standard pc power cord.  All power cord printer or standard pc with 3 connections will work fine.  I just hope that it is the power supply cord and not taking on the printer.

• Color HP LaserJet Pro 400 M451dw - error # 49

  We have the above printer. It has been working well for a long time now. It is configured with the ethernet cable.

  At this time, however, when the main user of the printer turns to for use, he first gets up says 'Ready', opens with the IP address then displays "error 49" "turn." This does not seem to do anything.

  I found a post that suggested by ensuring that the printer was not showing in the DHCP, and I do not see here.

  If anyone has any suggestions, please let me know. This is a printer that is much used by the primary user.

  Thank you.

  49 error usually means a firmware error (which could be due to a problem of trainer), but in some cases, it may be invoked by a sending system a use of "punk" (not necessarily a conventional print job) to the device.

  See thread http://h30499.www3.hp.com/t5/Multifunction-and-All-in-One/LJ-Pro300-color-MFP-M375nw-Power-cycling-displays-quot-49/m-p/6348735

• Color HP LaserJet Pro 200 M251nw to print alignment

  Images and text color print out of alignment.

  The problem started the first day that we had the impression.  It took me a while to get into this diagnosis, but I tried the following:

  I tried to replace the (expensive) with new toner cartridges.  The problem is even with the original Starter cartridges.

  I tried a reset of the complete printer.

  I tried to let the printer disconnected from the power supply for 24 hours.

  I tried several features alignment in the printer menu.

  Print black only is fine.  All other colors do not align between them or with blacks.  Creates a kind of 3D - ish into effect.

  The quality of printers report displays all colors fine areprinting, but not aligned with each.

  I have included scans of part of a rainbow impression that illustrates the displacement as well as the quality report page.

  

  

  Thanks for letting me know James_LAG.

  At this point, it looks like a hardware problem with the printer. Please call our technical support and you learn about a replacement printer, to 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. Contact HP.

  Thank you.