Music app gets stuck on the Apple music on my new iPhone 6 s more

Similar Questions

• iMac 8.1 stuck on the apple logo

  Model: iMac8, 1

  2.66 GHz Intel Core 2 Duo

  At 2BG memory when the problem started

  Mountain Lion 10.8.5

  Is in trouble with occasional frosts. Would be closed and it should restart very well. About 2 weeks ago, the computer froze. I shut down the computer and restarted. The apple logo came with the spinning wheel, and then just the apple logo.

  I can start safe mode. Tried resetting the PRAM, reset of SCM. Tried to start with all peripherals except keyboard and mouse disconnected. Use the command R to start the computer and went into the disc utilities. Disc checked and it said disc looks OK. Verified permissions. Mistakes came for iTunes more a warning which was not repairable. Fixed permissions. None of these permits to start properly.

  Parle talked anyone computer repair who suggested to unplug the computer, hold the power button while up to one minute, plug the computer back in and pressing the Start button. It came in fine. A few days letter that the computer froze and I had to stop it. You press the Start button, got the spinning wheel, so only the apple logo and apple logo. Start the computer by pressing command + R and reinstalled Mountain Lion. Installation once it stuck at the apple logo again. Active disk. Drive seems to be OK. Permission verified. Permission with iTunes but issues no warning this time. Repaired permissions. Nada.

  Inserted the installation disk, turned on the computer while holding D key. A ran Apple Hardware tools (tests of short or long). This error message came up twice with different numbers of rpm: 4MOT/1/40000003: drive HARD-110. I know that it's the hard drive fan. Computer repair man came out. Thought problem may be because I only had 2 GB of memory and ran only to open the Lion of mountain with several programs. Upgrade to 4 GB memory, which is recognized by the computer. But the computer still does not start correctly. Tried the Single Mode and run/sbin/fsck - fy. Said it seemed OK, but changed the volume. Ran he says once again and everything seemed OK. Still will not start.

  When I start in the disc, part of the grey background Utilities is missing. If you move the cursor on the screen, the gray background fills.

  Also, when I try from normally I get startup chime, the apple logo and the spinning wheel. After that make a spin the wheel stops, there is sort of a Flash, then the wheel goes and remains the apple logo. I can hear the computer tries to do something, then the arrow cursor appears and can be moved around the screen. It's like that.

  Also installed Mountain Lion on a USB key, it made the startup disk and tried to start the computer normally. Still will not start.

  Any ideas or suggestions for what could be wrong or other things to try?

  1. the present proceedings is a diagnostic test. It doesn't change anything for the better or worse and therefore, by itself, will not solve the problem. But with the help of the results of the tests, the solution may take a few minutes, instead of hours or days.

  The test works on OS X 10.8 ("Mountain Lion") and later versions. I do not recommend running it on older versions of Mac OS X. It will do no harm, but it will not do not much good.

  Do not be put off by the complexity of these instructions. The process is much less complicated than the description. You make the tasks more complicated with the computer all the time.

  2. If you do not already have a current backup, please back up all the data before doing anything else. The backup is needed on the general principle, not because of what anyone in the test procedure. Backup is always a must, and when you encounter any kind of problems with the computer, you can be more than the usual loss of data, if you follow these instructions or risk not.

  There are ways to back up a computer that is not fully functional. Ask if you need advice.

  3 here is instructions to run a UNIX shell script, a type of program. As I wrote above, it doesn't change anything. It does not send or receive data over the network. There is no to generate a report on the State of the computer human readable. This report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents for me or someone else.

  You should ask yourself if you can believe me, and if it is safe to run a program at the request of a foreign national. In general, no, he's not sure, and I encourage it.

  In this case, however, there are ways for you to decide if the program is safe without having to trust me. First of all, you can read it. Unlike an application that download you and click to start, it is transparent, anyone familiar with the code can check what it does.

  You may not be able to understand the script yourself. But variations of it have been posted on this site several times over a period of years. One of the million registered users to have read the script and set off the alarm if it was dangerous. Then I wouldn't be here now, and you would not be reading this message. See, e.g., this discussion.

  However, if you cannot satisfy yourself that these instructions are safe, do not follow them. Ask other solutions.

  4. here is a general summary of what you need to do, if you decide to go forward:

  ☞ Copy text from a particular web page (not this one) to the Clipboard.

  ☞ Paste into the window to another application.

  ☞ Wait for the test to run. It usually takes a few minutes.

  ☞ Stick the results, which will be copied automatically, in a response on this page.

  These are not specific instructions; just a glimpse. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait and paste it again. You don't need to copy a second time.

  5. try to test in conditions that replicate the problem, to the extent possible. For example, if the computer is slow intermittently, run the test during a downturn.

  You may have started up in safe mode. If the system is now in safe mode and works pretty well in normal mode to test run, restart as usual before running it. If you can test only in safe mode, this.

  6. If you have more than one user and a user is affected by the problem, and the user is not an administrator, and then run the test twice: once under the affected user and one administrator. The results can be different. The user that is created automatically on a new computer, when you start it for the first time is an administrator. If you are unable to log in as an administrator, verify that the user concerned. More personal Mac have only one user, and in this case this section does not apply. Don't log in as root.

  7 load the linked web page (the site "Pastebin.") Press the combination of keys command + A to select all the text, then copy it to the Clipboard by pressing command-C.

  8. start the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name ("Terminal") in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing Command + V, then press return. The text that you pasted should disappear immediately.

  9. If you logged in as an administrator, you will be prompted for your login password. Nothing displayed when you type. You won't see the usual points instead of the characters typed. Make sure that caps lock is turned off. Type carefully, and then press return. You can get a warning to be careful. If you make three unsuccessful attempts to enter the password, the test is still running, but it will produce less information. If you do not know the password, or if you prefer not to enter, just press back three times at the password prompt. Yet once again, the script will run.

  If the test takes much longer that usual to run because the computer is very slow, you can be prompted for your password a second time. The permission you grant by entering it will expire automatically after five minutes.

  If you are not logged as an administrator, you will be prompted for a password. The test will run. It just will not do anything that requires administrator privileges.

  10. the test may take a few minutes to run, depending on the number of files you have and the speed of the computer. A computer that is abnormally slow may take more time to run the test. During execution, a series of lines is displayed in the Terminal window like this:

      Test started

          Part 1 of 4 done at: … sec        …        Part 4 of 4 done at: … sec

      The test results are on the Clipboard.

      Please close this window.

  The intervals between the parties will not be exactly the same, but they give an approximate indication of progress.

  Wait for the final message "Please close this window" appear - again, usually within a few minutes. If you don't see this message in about 30 minutes, the test probably won't be completed within a reasonable time. In this case, press the Ctrl + C key combination or the point command to stop it. Then go to the next step. You will have incomplete results, but still something.

  In order to get results, the test should be allowed to perform or be stopped manually as shown above. If you close the window of the Terminal, while the test is still running, the partial results will not be saved.

  11. when the test is completed, or if you manually stopped, leaving the Terminal. The results have been saved to the Clipboard automatically. They do not appear in the Terminal window. Please do not copy from there. All you have to do is start a response to this comment and then paste it again by pressing Command-V.

  At the top of the results, there will be a line that begins with the words «Start time.» If you do not see that, but rather to see a mass of gibberish, you wait for the message "close this window". Please wait and try again.

  If personal information, such as your name or e-mail address, appear in the results, make anonymous before posting. Usually it will be not necessary.

  12. in the validation of the results, you see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the software which manages this website. Thanks for posting the results of the tests on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

  13. When you are finished with the test, it is gone. There is nothing to uninstall or clean.

  14. This is a public forum and others can give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but all that you can not be. For others who choose to run it, I do not recommend that you view the results of test on this Web site unless I ask.

  15. the related UNIX shell script is a notice of copyright. ASC readers can copy for their personal use. The whole nor any part can be redistributed.

• I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility.

  I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility. However, the next time you start, the startup process is blocked to halfway to new (on the screen with the toolbar and the status of apple). I want a more permanent solution to reinstall the operating system every time. Would appreciate someone's suggestions and thanks in advance.

  Replace your hard drive.

  You have a backup of trust? If not, buy a disc of exterrnal for that as well.

  The progress bar from the left end at the beginning of the commissioning indicates that your drive has been so damaged, it could not be mounted. Five minutes of progress bar is shown as it does the equivalent of disk utility (ERD [Directory]). If you have reinstalled several times and the problem is not fixed, your drive is in solid form.

• Is that what you can get siri on the Apple Watch (series 2) to make a phone call, but on your iPhone, so when you're driving it then would come by phone from car speakers?

  You can get siri on the Apple Watch (series 2) to make a phone call, but do it on your iPhone, so when you're behind the wheel, he would then come through car speaker?

  You can also long are you your phone is connected to the car blu tooth. Not tried myself.

• Is there an app Golf GPS for the Apple Watch series 2 which is "native" to the watch, in other words, should NOT be tied to an iPhone on the golf course?

  Is there an app Golf GPS for the Apple Watch series 2 which is "native" to the watch, in other words, should NOT be tied to an iPhone on the golf course?

  Hello

  You can find this app of interest:

  • PING
    • https://iTunes.Apple.com/us/app/ping/id440740108?Mt=8
    • http://www.Ping.com/about/insideping.aspx?ID=21779

• My iPhone 6 is stuck on the apple logo

  My iPhone 6 is stuck on the apple logo. If I put it to download it just stays like that or it stops and says it has no battery, even when plugged. I can't enter in recovery mode because my home button just stopped working out of the blue. I don't know what to do.

  Charge the battery for an hour and then try the recovery mode.

• Stuck at the apple logo & no backup to restore

  Well, I have an iPhone with ios 9.3.3 6. When I turn on my phone it stuck at the apple logo and after 10 seconds it turns off and when I turn it on again, same question.

  • Not having iTunes backup
  • No effect after hard reset
  • Tried to resolved via Recovery Mode, updated and restored but the problem is always there, always stuck and goes off

  Did you put your iPhone in DFU mode before resetting?

• Stuck on the Apple Logo screen

  My phone froze so I restarted. It got stuck on the apple logo screen and I tried to restore it. When I have it plugged into my laptop it would not restore because my boot drive is full. I tried to remove as much as I could turn off my laptop and emptying the trash and nothing will work. Its been sitting stuck/frozen on the logo of apple for 4 hours now. How can I fix it?

  Only way runs a restore via iTunes by putting the iPhone in recovery mode

• HP w1907: implementation gets stuck to the 'HP invent' blue Boot Screen

  Hi all
  
  I have HP w1907 desktop... I use it since 2008.
  Last month I format to have the new windows 7 in it... Previously I was also working with win7 Ultimate.

  But it's keep restarting after the use of 4-5 minutes and so I installed the entire operating system yet.

  It worked very well... after 3-4 weeks, when I started it, it gets stuck at the 'HP invent' blue Boot Screen.

  This display has the instructions to enter the "Boot Menu", "Setup" and "System Recovery" by pressing key "F11" aor "Esc", "F10".  It is just there for ever.

  If I try to enter the 'Boot' Menu by pressing the 'Esc' key, I get the message "Loading Boot Menu... ", but then it hangs there forever just.  If I try to enter the "Setup" Menu, I get a similar result - it says 'enter the Setup... ". "and just hangs there.  By pressing the "F11" key does not seem to do anything.

  Any ideas on how to solve this problem?

  Searching the forums I tried to reset the BIOS - who I've got from here:

  http://h30434.www3.HP.com/T5/desktop-lockups-freezes-hangs/powering-up-gets-stuck-at-Blue-quot-HP-in...
  
  and
  
  http://support.HP.com/us-en/document/c01080282
  
  After doing this too, the result is null

  Please help me...

  I'm in a hurry...

  Thank you.

  Date and the incorrect time can certainly cause problems.  What happens usually, however, is that the sites Web will not be opened because the State in which the certificate is not up-to-date.  I have not heard of the time and date causing the computer does not start.  I think that you need to change the CMOS battery.  Here's a guide on how to change it.  The guide has also some good troubleshooting information.

  Once the battery has been replaced, we'll see what happens.

• iPad stuck on the apple logo

  IPad is stuck on the Apple logo and halfway along the slide to download

  was reset as the wifi would not connect

  This can help:

  Press and hold the power button / stop and the Home button at the same time, the corners of the black screen,... .in taking... When you see the white apple logo appear to leave bot buttons go.

• Laptop stops randomly and gets stuck on the saving settings

  Basically, we have some laptops 10 + this will stop randomly and get stuck on the "saving settings screens.

  Here are the different models of toshiba R500-R600 M10 M9 M5

  We changed versions of bios etc, reimagee them, even used an image of windows xp disc rather than soe.

  Hardware tests OK and customers do not something in particular, some when others when you connect using applications office, back in after a while. Some use docking stations, others not.

  All ideas

  Hello

  Just a question: are you an authorized service provider?
  I ask this question because it looks like you are an ASP because you have so many laptops and you have tested different things.

  It's really hard to say what the reason is for this but I think that in this case, you should contact Toshiba directly. Maybe it s a known issue and it can be fixed in a few minutes.
  So ask for it and wait for a response.

• Sometimes, the Lenovo Y40 gets stuck on the Lenovo screen?

  The Y40 I bought in July sometimes gets stuck on the Lenovo screen where the laoding circle does not appear. It happens only intermittently, but occurs more often after long use (more than 45 minutes). Technical support already tells me to reset the BIOS and restore windows. Do you know the guys from any thing that can cause this problem? Would it be a HARD drive broken or damaged OS? Thank you!

  I've already sent my laptop in for repair. The technical support representative said that it was either a HARD drive or motherboard problem

• Servo motor gets stuck in the loop

  My project is to control two motors from the pedals with LabVIEW in combination with UMI-7774 and PCI 7350.

  I use a traditional format of State Machine to simultaneously control two motors according to the absolute position mode.

  In one of the first States, both motors are wound manually by using the speed mode (to make a desired voltage).

  In a later State, the motors are wound to a position specified by the user when you press a foot switch. When you press the other pedal, they are then held in the previous "original" position

  After the first "Tension" indicate when the winding engine and the course due to the pedals is running, the program gets stuck in the State of wind.

  Although drivers are told to go to a specific position, they never move and that's why the program is unable to move to the next State.

  I've attached a screenshot of the winding State where the program is stuck (the engines are not mobile, so when the final position is to compare it with the desired position, the loop continues to go).

  Help, please.

  CAT

  I solved the problem.

  States "Wind engine left" and "Right wind engine" speed has been put back to zero. When the program moves toward States of wind/flow, the speed is always zero (the engines cannot move).

  I simply set the speed value desired in each of the States LBL/RBL (that allowed the engine to get to the position of desire).

  Thanks for all the help,

  Catherine

• Everything I print gets stuck in the queue, but the document is printed

  ORIGINAL TITLE: Spooler

  I installed a printer on a pc windows 7 64. Everything I print gets stuck in the queue, but the document is printed. The printer is on the network, I tried to restart the spooler and erased the record of the spooler, but perisisted of the question, given that the document gets stuck, no other agency will be able to print, remove the paper and print again to print but the file gets stuck again on the queue. I tried to change the IP address, but the same thing happened. Can someone help me?

  Hi, Omorguz,

  Printer brand and model, if you please.

  Start > run > type services.msc

  Press enter

  Scroll down to print spooler

  Select stop

  Let Windows stop the spooler

  Control Panel > printers and Faxes folder

  Right-click on the printer icon, then select open

  If you see pending orders in the queue, select the

  Click file > cancel all Documents

  If a job shows the deletion, but never finished, open the command prompt window

  Start > run > type cmd

  Press Ok

  Enter Net Stop Spooler

  Press enter

  Wait for the DOS window opens and is

  Open the command prompt window

  Type Net Start Spooler

  Press enter

  If that does not cancel the print job:

  Your directory of spools Windows XP is located at

  C:\WINDOWS\SYSTEM32\SPOOL\PRINTERS

  It will usually contain files like these:

  FP00008
  FP00008. SHD

  There are two files for each remaining print job.  Just delete these and restart the computer.  Your queue should now be provisioned.

  If you are printing over a network, and the queue is not clear after the above steps:

  Go to the computer that has the shared printer connected and perform steps 1 & 2 above.

  If this does not work, then go to the computer when he was sent to the printing of the task and perform the steps 1 & 2 on this computer.

  Run chkdsk

  Start > run > type CMD

  Press Ok

  Type C: chkdsk/r/f

  Press enter

  You will receive a message re: volume must be locked and you want to start scanning reboot?  Press y and press enter

  Type Exit to close the CMD window

  Restart the computer for the scan at startup

  This will check the integrity of your data on the hard drive of computer as well as find and fix errors that could corrupt your data or program files.

  I even recommend that you uninstall the printer and when you are done uninstalling, restart computer.

  When you reinstall the printer, reinstall it using the compatibility mode

  How to install a hardware device using the compatibility mode driver.

  http://social.technet.Microsoft.com/forums/en-us/w7itprohardware/thread/80cae5ee-dc98-4A2F-8284-a1ab826059b7

  It works on Windows 7 Professional, comprehensive and business - Windows XP Mode - it's free

  It's the best of both worlds: the new Windows XP Mode allows you to run Windows XP older right on your Windows 7 desktop business software.

  http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-XP-mode

  e FAQ or choose a link from the top of this page.

• When I send a message it gets stuck in the Outbox and won't unless I click on the message until it is "BOLD" with a print, then delete.

  Forwarded messages or new messages are not automatically leave and get stuck in the Outbox.  If I leave it alone, I get a message that there was an error and the message could not be sent.  However, if I leave the message stuck in the Outbox, the message gets actually released several times until I have go into the Outbox and delete the message.

  Compacting files try one at a time.

  To defragment:

  Start | All programs | Accessories | System Tools | Disk Defragmenter. Just above that you'll also see disk cleanup. I was running first and also in the other Options tab, the third option to get rid of old that take place of restore points.

  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA