Mute switch and suite

Similar Questions

• OK to mix 'of connection to the switch"and"close relay switch?

  Hi all

  I'm developing a test sequence using the card multiplexer 2527 to the track signals.  To configure the card, I use DAQmx switch functions.  In my application, I have a Subvi routine that imports the data from a spreadsheet Setup and run a loop for to set the configuration for each step (each iteration of the loop contains the channel for 2527 card information).  The topology is set on the first iteration, as well as the configuration of the path to the first string.

  My concern is this: I need to close the extra channels/relays without changing the topology or resetting the device.  In the first round, I use "connection to the switch" function to set the initial path, (ch0 to com0 for example).  Then in subsequent iterations of the loop, I use "Relay close switch" function to close the additional channels individually (for example k2).  In the end, when the measure is taken, both ch0 ch2 must be closed and routed to com0.  This implementation is so sure, or am I somehow to make the adjustments to the initial loop?

  I would like to test this with the hardware, but it is not yet available.

  Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer.

  Please notify.  Thank you.

  GSinMN

  Hello GSinMN,

  It's OK to mix 'of connection to the switch"and"Close relay switch"If you understand what's happening below. "Switch Connect" connects two channels by closing a path of relay between the channels, then "Close relay switch" can be used to change the State of the individual relays. If you are not careful you can mess up your connection by activating / deactivating relays that are part of the route connecting your channels.

  "Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer."

  I would recommend the topology independent if you want to stick with connections to channels only. http://zone.NI.com/reference/en-XX/help/375472G-01/switch/2527_independent/

  Initial connection:

  CH0-> pcom0

  pcom0plus-> icom0plus

  pcom0minus-> icom0minus

  icom0-> com0

  In each future iteration just connect to the next to pcom0 channel (which will be indirectly connect it to com0):

  CH1-> pcom0

  CH2-> pcom0

  ...

  ...

  Jarrod

• Front Panel Bank of switches and related indicators

  I am the design of a test system.  I would like a Bank of the individual switches on the control panel to turn the test case.  I figured out how to do this.  And I can do banks for the indication LEDs (pass/fail) and the field of digital test result.  But, I want to tie them together.  I guess I should start by using a cluster rather than a table.  But how to get banks to act as a single group?

  As I have so far, I have a back of switches and a Bank of indicators (of the switching status) for all just play.  The indicators do not align with the switches. I'd like a match of 1 to 1 for easy operator use.  When I use 'properties' to develop the Bank of the indicator, it won't take the number.  It is limited internally somehow.

  DH

  How about an array of clusters? Easy to use and easy to watch, all lined up.

  

• Details of the 536304-001 HP Power On / Off switch and cable LED Assembly for the Z400

  Can someone help me with the P5 front header pinout on the motherboard Z400 or on the HP 536304-001 power switch and LED to the Z400 Cable Assembly?   I'm getting to is a Z400 motherboard in a case of XW8000. I know that 536304-001 does not fit in the case of XW8000 but the XW8000 part equivalent seems to have mostly the same connections. double color led, led hard drive, power button / stop.   I can see an illustration that 536304-001 use 4 connections on the side to key of header and 2 on the other. Cable colors are red, green, black and 3 white. There are also other connections to the temperature thermistor that I would not intend to use (unless explicitly required for Z400 motherboard).

  Here's a panel header pinout before Z400 P5 motherboard:

  

  Find "missing" pin key 14 to steer this diagram properly.

  Pins 2 and 4 go to the power LED.  This LED is two-way, with green in a sense (normal) and Red (diagnosis failure) in the other.  If the LEDs back to back are installed between pins 2 and 4, on lights.  If green it does not illuminate during normal operation, move the pins to the pair of diodes.

  Pins at 15, 17 and 18 are chassis ID pins.  It's OK to let those pins unconnected.

  Pins 6 and 8 are the power button pins.  Connect a normally open push switch between pins 6 and 8.  Do not attach any tension or Chin-ups to this switch.

  RESET # may not work, but it is a prototye signal.  A switch push-button normally open between pin 7 and 6 (GND) could make it work.  It's OK to let those pins unconnected.

  Terminals 11 and 12 are the thermal diode in the panel cable Assembly before Z400.  The system starts without the thermal diode, but fans can operate at full speed all the time, or may oscillate in speed (several times to go from slow to high-speed and back).  This will make the system very noisy.

• The hand left panel doen't show the usual "Control Panel Home" switch and my control panel display is stuck on the classic view.

  The same thing happened to me recently: the hand left panel doen't show the usual "Control Panel Home" switch and my control panel display is stuck on the classic view. Click on "Show common tasks in folder" but that doesn't change anything. Finally, I tried a restore without success point. No idea how to get back the link "control Panel Home"?

  Thank you very much for your support

  Alain Truchat

  Split from here:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-desktop/left-hand-pane-on-Control-Panel-missing-XP-Home/6ca7e184-e2be-4709-b865-81e5c3702629#last

  Hi, Alan.

  Reset Control Panel-
   
  Press Windows key + R
   
  Type inetcpl.cpl regsvr32.exe/n/i
   
  Press ok

• Why the fast user switching and the new Windows Search use the Terminal Services?

  Recently, I was struck by a piece of really bad, malicious malware that totally trashed my operating system.  Therefore, as I rebuild my system, I am applying the appropriate safety precautions.  Among the recommendations of Microsoft is to reduce your footprint of security by disabling unnecessary services.  One of these services that I thought I didn't need was Terminal Server services, since it is a way for a person to get to my machine remotely.

  It turns out that, however, other services that I want to use, such as Fast user Switching and window new search utility, depend on the Terminal Server Services.  It makes no sense to me from a safety point of view.  This seems to be a bad design decision, because security trumps utility.

  If Microsoft is listening, I would like to know why you made this decision and you have changed in Windows 7?

  Second, is there a way to always have the Terminal services Server running and at the same time cut access remotely through this service?

  I don't know about the 'new' Windows Search, but what about the fast user switching you ask to run several sessions of Windows when you switch between users (a session for each user connected) and the only way that Windows can do is to act as a quasi Terminal Server, it needs Terminal Server services to run multiple sessions.

  John

• MUTE button and its quick launch icon are reversed

  I think I deleted a driver when I was trying to fix a computer freeze. There was a message I deleted it while my computer may not work correctly, but I did anyway... Oops.

  So now, when my mute button is disabled on the motherboard, and then the audio in the quick launch shows it is not muted and when the mute button is reactivated, then the icon down below shows that it remains silent. So I guess they are reversed but I virtually impossible to get all the sounds work so that never.

  One thing I noticed, is that if I hit the mute button permanently, I can hear bits of sound. It's like I'm sneaking between the functions mute above and below. But of course, I need to function normally if I can watch YouTube with ease, etc..

  So what to do? I tried to reinstall a driver from the windows site, but I couldn't really handle this very well. And my driver installation CD does not work because my CD rom is not working well.

  Hello again triceratops108,

  Thanks for the quick response!

  Based on the information provided in your post, I recommend to uninstall and reinstall the audio driver of your computer. To do this, please follow this document on How to change or remove a program in Windows XP as well as Conexant CX20468-31 AC97 Audio Driver and Audio Driver EQ re - install on your laptop.

  If the problem persists, I recommend reformatting your hard drive and re - install Windows XP or if you choose to do, upgrade to Windows Vista.

  I hope this helps!

• Put on mute, Volume and WLAN touchpads does not

  I have a dv6 HP Pavilion Entertainment PC (laptop), running Windows 7. a few weeks back the keys Mute, Volume and WLAN has stopped working.  Yet I have not been able to determine what is causing this or how to solve the problem.  I found other poster there this same material, but have not found a solution.  Requested technical support from HP, but that ended up having me wash it all away and start again, which did not fix the problem and had me all rebuild.  Won't do it again, any help out there?

  Don

  Hello

  Perform a hard reset

  1 disconnect all devices and remove all USB devices and multimedia cards.

  2 disconnect the power adapter, remove the battery and then press in and hold the button for at least 1 minute.

  3 reconnect the power adapter (do not connect the battery), press the power button.

  Verification is your problem with buttons.

• I m problem that my computer automatically turns off (is not closed correctly at the time of the switches) and when I start it gives message that windows do not close properly seeded.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Previously I was using WIndow Vista Home Premium but recently I installed Windows Vista Ultimate.I m having problem my computer turns off automatically (is not closed correctly at the time of the switches) and when I start it gives message that windows do not close properly seeded.

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  information on errors such as STOP and information such as IRQL_NOT_LESS_OR_EQUAL codes or
  PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  Displays information on all the "crash" of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, drivers particularly video drivers but it
  are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• New switch and can not download IOS

  Hi all

  I just bought a new DS-C9124-K9 Cisco switch and there is no OS on it, when I go to download the operating system I get an error saying"

  Required service contract
  To download this software, you must have a valid contract associated with your Cisco.com profile.   If you do not have a service contract you can get one through: Your team if you have a purchase contract direct with Cisco Cisco Your Cisco partner or reseller   Once you have the service contract, you must associate your service agreement with your Cisco.com user ID with the Profile Manager

  "

  How can I fix this to get my ass expensive switch work XD

  AH, I forgot the problem. in any case you need cisco smartnet account or valid service contract are necessary for most items to download on the cisco Web site. If you don't you should contact your Cisco team account if you have a Direct purchasing agreement or contact a Cisco partner or reseller to purchase a service contract.

  Concerning

• No "ip Routing" command on the switch and still intervlan routing.

  Hello

  In my companies 4500 switch I see there is intervlan routing configured for 4 VLANS there but I don't see any command "ip Routing" on this subject

  to enable routing on the switch. A switch can route the same if the command is not there?

  Ninja,

  Default configuration options often do not appear in "show run".  Please try «performance see all»

  Kind regards

  Christopher

  PS your switch and device business, not small business.

• I have a license for Design CS6 and Suite Web and applications downloaded, but they do not load or ask for activation. [was: question]

  I have a license for Design CS6 and Suite Web and applications downloaded, but they do not load or ask for activation. What should I do?

  It's a Mac and finally got to window that let me enter the license key and it works. I thank you for your response and departure to help!

• A distributed virtual switch and create Portgroup

  I'm looking to automate the "creation" of the distributed virtual switches and exchanges.

  I was unable to justify these functions in the released PowerCLI.

  I only found orders that allow me to refer to an "existing" Distributed Virtual Switch.
  I've seen references to a "adventure".  But all the dates related to the 'adventure' seem to be well over a year.

  What programmatic support exists for 'creation' of distributed virtual switches and exchanges?

  Luc's response was right, that if you cannot use the fling then the module is probably the best place to watch right now.  While we cannot commit future versions, I can say that vDS is high on our list of priorities and we hope a future release will include supported cmdlets to work with.

• Turn on the mtu on cisco switch and cisco user server

  Hi all

  someone got bad luck turning on the mtu on their cisco switch?  I guess I need to turn it on for all because the command is for all ports on cisco catalyst and my server switch is nearby to my user of switches and a broadband bandwidth 6 G or 6 ports, I need to turn it on for all user ports?

  Thanks for any comments, that you can add.

  I assume you mean Jumbo frame support! You shouldn't have any problems with that. Please take a look at for example http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml for more details and the configuration of the different switches. According to the model, the parameters are for dedicated ports only or the entire switch. In the case of the switch everything you will need to reload (reboot) switch, so be careful.

  André

• Difference between a Standard switch and distributed virtual switches

  Hi people,

  I wanted to know the difference between a Standard switch and virtual distributed Switches.What benefits (characteristics) of displacement or migration from switches Standard using Virtual Switches.Any distributed on this will be appreciated.

  Thank you

  vmguy

  In this article, there is more information on these two concepts, Overview of the concepts of vNetwork Distributed Switch.