MY ACER LAPTOP IS UNABLE TO START

Similar Questions

• Unable to start my laptop due to c:\windows\system32\config\system

  Unable to start my laptop due to c:\windows\system32\config\system missing or damaged

  Hello

  ·        Remember to make changes to the system?

  I suggest you to follow the steps mentioned in the article below and let us know if the problem is solved or not.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I tried to install windows vista on my laptop but I m unable to start because of a message error loading operating system.

  I tried to install windows vista on my laptop but I m unable to start because of a message error loading operating system. good quick response.

  Hello

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  Here's how to do a clean install of Vista:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  See you soon.

• My ACER laptop will not start Vista

  My acer laptop does not start correctly. It loads after windows bar loads and then it stops quickly. the pointer will appear on the screen and when it is left idle, screensaver maker runs. the same thing happens when I try to start in safe mode. What should I do? any help much appreciated.

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  How to reinstall Vista on an Acer:

  "With the help of the outside Windows Recovery Management"

  http://Acer.custhelp.com/app/answers/detail/A_ID/2631

  See you soon.

• Ms more recent update for my VISTA plus old (2008 Acer laptop) was the last event, now cannot start PC... recovery tests without success... Help, please...

  Ms more recent update for my VISTA plus old (2008 Acer laptop) was the last event, now cannot start PC... try to recovery without success, a loop back and asking to recover or normal boot...  Attached to jumps, safe to ask if I want to recover...  I never received an OEM of VISTA version, but the first time having problem after all these years...   Help, please...  Would contribute to a boot disk, if so, how can I get a copy?...  Thanks, Dave * address email is removed from the privacy *

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And here's how to use Recovery of Acer.

  http://Acer.custhelp.com/app/answers/detail/A_ID/2631

  To start the system recovery:

  1. Restart the computer.
  2. When the Acer logo appears on the screen, press the left Alt and F10 keys.
  3. If you are prompted with a Microsoft Windows splash screen, press the Enter key.
  4. After that the Acer eRecovery Management application is loaded, select your type of restore.
  5. Read the review and then click Next when you are ready.
  6. Click Next to start the restore process. It may take 10 minutes up to an hour fom anywhere to restore.
  7. Once the restore is complete, your computer will restart. After the reboot it will load Windows and start the installation of your software and drivers. Your computer will restart several times during this process. Once they are all completed, your computer will be like it was when you bought it first.

  See you soon.

• I get the following popup when I start my Acer laptop with Windows 7 - Microsoft dynamic C++ Debug Library...

  I get the following popup when I start my Acer laptop
  with Windows 7 and I use Google Chrome as My browser - I would like to know how to
  it stop what happens when windows starts. -Thank you--->
  Dynamic Microsoft C++ Debug Library
  program: C:\Windows\system32\igfxsrvc.exe
  File: D\Program Files\Microsoft Visual Studio
  9.0\VC\ATLMFC\INCLUDE\atlcom.h
  Online: 2475
  Expression: 0 & "communiqué called on a pointer that has.
  already been released.
  For more information on how your program can cause a
  the assertion failure, see the Visual C++ documentation on
  argues.
  (Press Retry to debug the application)
  Choice to follow:<--Not seen="">
  Abort Retry Ignore

  Hi Chris,

  This problem may occur because of the conflict between certain third-party applications.

  We will start the computer Safe Mode to check if the problem occurs in Mode without failure. If the problem does not occur in Mode safe, then you can try to set up your computer in a clean boot state to find what startup item or service is causing the problem.

  Step 1:
  To restart in Safe Mode, see the link.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  If the problem does not occur in Mode without failure, then you try to put the computer in a clean boot state.

  Step 2:
  To perform Clean boot follow the procedure below.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Acer Aspire laptop computer does not start

  Lites button power screen stays black, the system tries to start, but he keeps power button light turns off.  I have a new disc of windows 7 32 & 64 bit.  I have the disc as a dvd before I turn on the power button.  With the new windows 7 dvd of 20 to 30 seconds to place power turns off.

  Anyone with knowledge of this problem would be grateful.

  Thanks in advance

  Hello Mojo,

  Thanks for posting your query in Microsoft Community.

  I imagine the inconvenience that you are experiencing and will certainly help you in the right direction to solve the problem. However, I would be grateful if you could answer a few questions to refine the question in order to provide you with better assistance.

  1. You did it any significant hardware or change software on the computer before this problem?

  2. What is the brand and model of your computer?

  3. What are the troubleshooting steps you have tried so far?

  I understand that you are unable to start your Windows 7 system. To prevent your system from automatically restart, try to access the menu advanced startup options by turning on your computer and pressing the F8 key before Windows starts. Select the option disable automatic error system reboot. Also, I suggest you try the following steps of diagnostics to verify if you are able to reach the office in one of the following modes methodical.

  Method 1:

  Please follow the underlying steps:

  Step 1. Disconnect all external devices except the keyboard and mouse.

  Step 2 I would like to start your computer in last known good configuration.

  If method 1 does not work, go to method 2.

  Method 2:

  Step 1: Try to start your system in a State of services necessary to the operation and a minimum set of drivers enabled, called Safe Mode.
  Start your computer in safe mode

  Step 2: If the system works fine in safe mode, try to clean the system startup:

  How to perform a clean boot in Windows

  Note: See "How to reset the computer to start normally after a boot minimum troubleshooting" to reset the computer to start as usual after a repair.

  If method 2 does not work, go to method 3.

  Method 3:

  As you cannot start your computer at all, I suggest to run a Startup Repair to repair the damaged boot system files and try to boot into normal mode. See the section: How to use Startup Repair in the following link.

  Startup Repair: frequently asked questions

  If this does not help, try to boot from a disc to install Windows 7 on the Windows recovery environment mode and then try to run the Startup Repair tool and check if you are able to start normally.

  If the problem persists, proceed to method 4.

  Method 4:

  You can use the Bootrec.exe tool in the recovery Windows (WINRE) environment to troubleshoot and repair the following items in Windows Vista or Windows 7:

  • A master boot record (MBR)

  • A boot sector

• A Boot Configuration data (BCD) store

Note: When you are troubleshooting startup issues by using the Windows RE, you should first try the Startup Repair option in the System Recovery Options dialog box. If the Startup Repair option does not resolve the problem, or if you must troubleshoot more steps manually, use the Bootrec.exe

Use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows 

Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• Unable to start - blue screen STOP: 0X0000007E

  original title: STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578)

  I was working on my laptop Acer Aspire and suddenly my restarted windows and then leave her unable to start and just show a blue screen with the error code as STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578).

  I tried to run in safe mode, then even I tried all the options available in the Advanced menu to restart that we get after pressing F8 but just fails. Repair of the system showed the error Impossible to repair in the same way his unable to restore and unable to start with last successful boot setting.

  Kindly let me know what to do I have lots of important data in my hard drive that I don't want to lose.

  Hello

  Unless the drive itself is completely fried the data on disk can be recovered by putting the hard drive
  in another computer as 2nd or a case of external hard drive using a USB connection - then the data
  likely to be backed up or copied to other media.

  Of course, the major problem is that the system does not boot even in Safe Mode.

  Setup/settings (BIOS/CMOS) often F2 so screen shows that it boots CD/DVD on the 1st in the boot order-
  Start with a Windows 7 disc and try the Startup Repair tool. Also, try restoring the system from there. (Don't forget to)
  Set the boot order to when.)

  Those who cannot not helped at all and will need you the help of a real computer store (no leeks and)
  Displays a BestBuy or other stores) or system manufacturer support.

  =================================================================

  Here are the usual methods to troubleshoot the bluescreens if you have access to some and still have a
  problem.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top 3 answers.

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  -----------------------------------------------------------------------------------------------------------------

  The system has RAID? If so, it is very suspicious.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-
  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Unable to start after you run the product recovery disc

  Hello

  My laptop was a dual boot with windows XP SP3 and ubuntu

  1. He was infected by the virus and when I tried to clean it I removed the wrong file "services.exe", whereas windows does not work good there

  2. when I tried to uninstall the windows update, I get the error following error: 1068: the dependency service or group could not start

  3. so today, I found the toshiba recovery disks, I run and it commpleted, but now am not able to start my laptop.

  4. when I try to re - install windiws xp I got the error below "couln can't find NTLDR.

  Guys, your help will be much appreciated

  Hello

  > I run and it filled, but now am unable to start my laptop

  Are you sure that installation completed successfully? Looks like the damaged MBR or cannot be attributed

• Satellite P15-S420: unable to start Windows XP

  I hope that all makes sense... I'm unable to start after the start page of Windows XP. I think I have assumed that the computer turn off when there is no. The battery may have exhausted and when I plugged it back in and tried to start it would not.

  When the Windows start page is in place, it seems that HD works for awhile, but stops and goes no further. I am able to boot in safe mode and have tried to restore with no effect. When I click on Toshiba Manager of power supply in the control panel I get "Policy of NoteBook Load Fail" this could be a problem.

  What do you think???
  Oh, I have a Satellite P15-S420.

  Hello

  In my opinion, this power saver error message occurs because you started the laptop in safe mode. In this case, the OS doesn't use the Toshiba drivers that are required for the use of additional applications.
  You write about the restore procedure. Have you tried to install the laptop with the supplied restore CD? If this isn't the case, then try it.

• ERROR: Unable to start Bluetooth stack service

  I seldome use features wireless to my pc before, but now that I have the wireless router I frequelty use it. Usually, I turn on the wireless switch and turned off to save the battery. I noticed every time I turn on the radio, after a few minutes, that an error message is displayed:

  BTTray

  ERROR: Unable to start Bluetooth stack service

  I don't know if what is wrong with my laptop. Please if anyone can tell me if what is wrong with this thing. Thank you very much!

  HP pavilion dv6820ee

  OS: Windows Vista editions Home premium.

  Message edited by xXxonins on 12/22/2008 05:27

  Access your product download page and reinstall the software for bluetooth under networks:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & Product = 3716846 & lang = in

  then, under network connections in the network and sharing window - see if you have a bluetooth adapter that is listed.  If you do not use bluetooth, you can turn it off or you should be able to set it up properly.

  If fails it then in Control Panel, under administrative tools, Services - locate service BTtray and disable it.

  HTH

• Windows is unable to start.

  Owner of a Pavilion wa694ua #aba little more than 2 years.  Windows is unable to start.  During windows Startup Manager, I receive a status of: 0xc000000f and info: start the selection has failed because the required device is inaccessible.  What to do next?  I have the recovery disks, but is not no longer works.

  Your hard drive may have failed and must be replaced. Enter the BIOS by typing/holding the F10 key immediately after switching on the laptop. Use Diagnostics to test your hard drive.

• Unable to start bluetooth stack service

  I can't not connact my phone to my laptop via bluetooth and get the following ERROR... UNABLE TO START BLUETOOTH STACK SERVICE.

  A large part of the obligation for any help.
  Thank you

  Hello

  Method 1.

  Try these steps and see if it works.
  Step 1: Start the Bluetooth service.
  a. Click Start, type services.msc and press to enter.
  b. in the list of components, double-click Bluetooth support Service.
  c. change the startup type to automatic and click on the Start button to start the service (verification of the d.       d.Dependencies of this service and make sure that they can also be programmed to automatic)
  e. click on apply and then click ok.

  Method 2: Bluetooth device driver update. Steps to update the device driver:

  a. click on start

  b. Select Control Panel

  c. Select system and maintenance

  d. click Device Manager (if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.)

  e. in the Device Manager, look for the Blue tooth device

  f. click on the driver tab, click Update driver

  Link for reference: updating a hardware driver that is not working properly

  http://windowshelp.Microsoft.com/Windows/en-us/help/b3c6477e-1111-4B9F-A52A-fffdc51e9c901033.mspx

• Want to buy the computer acer laptop

  Does anyone have suggestions on buying a cheap Acer laptop with or without optical drive

  I bought an Acer Aspire R7 R7 571/R7-572 in 2013, I have no regrets.  It's a portable tablet convertible and I particularly like this feature.  Not so much because it's an Acer, but because I can fold the monitor flat on top of the keyboard or just pull it forward and adjust it to my line of vision or to stop a glow of a lamp.  This Acer has a very fast start up.  I put 10 W on it when it is released.  I also ordered the stick of reformatting, but it is very expensive compared to other manufacturers. Be able to reformat saved a lot of money since 1996.

• Windows do not recognize the 'certificate' Acer laptop wireless signal. can, t go online? pls help.

  The wireless router from the time warner Server acer laptop says the signal is strong and is connected, but a sign comes up saying windows cannot recognize the certificate for the server? cannot go on using Explorer or mozilla lps.

  Hi trickstar46,
   
  Follow these steps to resolve the problem:
   
  a. Click Start--> programs-->--> Communications accessories-click--> select--> right click on your connection network connections and select Properties.
   
  b. click on the Authentication tab--> disable / uncheck the authentication of the IEEE 802 option. 1 x for this network.
   
  c. click on apply. Click OK.