My Canon sx260 does not communicate on my computer?

Similar Questions

• Canon printer does not connect via the IPP Protocol

  I work in a company that sells printers offices/schools/etc. Yesterday, we received a call from a customer indicating that the Copier, we sold them connected not to a new computer they bought.

  I went to the site and noticed that the computers in question were all purchased during 3 months and all loaded with Mac OS X El Capitan. Most was registered on 10.11.3, and some 10.11.2 and 10.11.1. All computers work turned Yosemite.

  We receive a message somewhere in the sense of "Communication error. This printer may not be able to [print], you want to save it anyway? »

  It was a cannon imageRUNNER Advanced C5235. The client declares that if he saved the printer, it would not be able to print, but would still see jams paper, messages and other statutes of the computer printer toner. After attempting to remove and reinstall the printer using the most recent driver available on the Canon Website, we received the same error, the customer received. We escalated it to Canon support, who asked us to choose LPD instead of the PPI for the Protocol, allowing the printer to you connect and start printing on all devices running El Capitan.

  After further research, to my knowledge, the ISB is more recent and has more features that the LPD, although I couldn't find much on it so I was uncertain about the origins of these two protocols, except that they were introduced in the 1990s. I know it's kind of vague, but is better/more recent than PPI LPD? If so, great. Otherwise, is there a way to solve this problem and get computers that run El Capitan to connect correctly using IPP?

  The problem here is that the driver Canon UFR2 or PS that was used on the Mac to print in ADVANCE of Canon C52xx does not support PPI. This is why you must use an alternative Protocol.

  Note that it is possible to print to the C5255 using the PPI, but you need to use the Canon PPDs which means the copier must have the kit installed Postscript printer and you get not the pretty picture base views the pilot UFR2 and PS to give you.

  Second point is that the Canon UFR2 and PS drivers, it is preferable to use HP Jetdirect-Socket to the LPD protocol. He sent larger packets and verifies the status of the target unit - LPD simply sends data to the fixed IP address so if the printer has a problem you don't get this information until you walk up to the photocopier.

  I hope this helps. Answer if you need more information.

• Photosmart 6510 does not communicate wirelessly with Mac 10.8

  I have a photosmart 6510 and an imac on 10.8

  Both worked very well together, with all functions wireless works very well, until two days ago.  Two days ago, I changed my ISP and I have a new router. My mac and printer are connected properly to the new router, but they don't communicate wireless now.

  I am able to print the wireless network test results and everything seems fine.

  But when I send anything to print I get a message saying that the printer does not communicate or can't find the printer.

  So I uninstalled and reinstalled the printer drivers and all of the HP software. Everything was fine - the installer sees the device when the usb cable is connected, it indicates that the device is connected to the correct network and upon request I have unplug the usb cable.  But then I get an error warning:

  Device not found on the network:

  Wireless network settings were downloaded successfully on your device. However, your Mac could not locate the device on the network.

  Please make sure that:

  • Your Mac is connected to a wired or wireless network that has access to your device.

  • Your device is connected to the network wireless "TALKTALK".

  Click on "Start over" to try to connect using the current settings. Click 'Go Back' to enter different settings.

  And at this time, I'm stuck.

  Can someone advise please how do I get the printer to work again wireless?

  Thank you

  I think I've solved. restore the factory settings and then reconnected and the corrected IP itself.

• Your 'help' rarely works. How can I click on something that does not appear on my computer?

  Many problems of migration from Windows Live Mail. I imported my contacts, but they are scrambled. The columns contain erroneous information. Is it possible to decode them? Your 'help' often tells me to click on something that does not appear on my computer. Very frustrating to go through aid procedures which lead to a white wall.

  As for aid referring to things you do not have...

  http://chrisramsden.vfast.co.UK/13_Menus_in_Thunderbird.html

• Satellite Pro L300 - CD/DVD does not appear on my computer

  Hello! This is probably a silly question / easy but I am very new in this and... my CD/DVD unit does not work.
  It does not show on 'my computer' and when I insert a disc, nothing happens (with the exception of a humming noise but then nothing)...

  Please can someone help me?
  As the helpline does not respond on Saturday...

  Thank you very much!

  Hello

  Try this;
  Go to the Device Manager and remove the drive from the Device Manager list CD/DVD.
  Then access the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Reboot the laptop and check again.

• Toshiba Canvio Basics HARD drive does not appear in my computer

  Hello

  I have a HDTB110AK3BA - Toshiba 1 TB Canvio Plus Portable Hard Drive for storage 3.0 Basics and the computer will allow it to connect, but it does not appear in my computer / pc is in Device Manager thought but not my pc

  Please help and Windows 7 or windows 8.1 PC do the same thing.

  Hello

  I found the description of the product of this external HARD disk:

  Product features:
  • USB 3.0 - powered portable add-on storage.
  • Voltage of bus capable USB, no need for AC adapter.
  • Easy to use with no software to install.
  • Adapts to large digital files with spacious storage capacity.
  • Protect your drive (internal shock sensor and ramp loading technology).

  Specifications
  • Capacity: 1.0 TB
  • Interface: USB 3.0
  • Transfer rate: up to 5 Gb/s
  • Speed: 5 400 rpm
  • Average access time: 12ms
  • Cache buffer: 8 MB

  It is a HARD USB 3.0 drive. No doubt the HARD drive is not recognized correctly in windows exploerer due to the low power.
  The USB 2.0 port common feeds only 500mA. The USB 3.0 device must be able to 900mA.
  Therefore, it would be advisable to connect this 2 ports USB 2.0 HARD drive with a USB Y cable

• Drive external DRIVE does not appear in my computer

  Windows says new hardware detected... your new hardware is installed, but it does not appear in my computer. No drive letter is assigned.

  Can anyone help?

  Do you use an external USB HDD? Does a job on another computer?

• Wireless stopped working, the error message says "this wireless does not work on this computer ' even if another computer at home has no problem with wireless services.

  My computer stopped working wireless, the error message says "this wireless does not work on this computer ' even if another computer at home has no problem with wireless services.  I've tried everything and my router is intact.  My Protection of Kaspersky flags are gone from green to red and says threats have been detected. What should I do to get back on the wireless.

  original title: Wireless not working not

  Hello

  1 have had any changes made on the computer before the show?

  2. what operating system is installed on the computer?

  Method 1:

  Check the link and try to run the troubleshooter to check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Try to run Microsoft Safety Scanner for any malware or spyware infection and check if it helps.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again. The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• acerEXTEND does not load on the computer (Windows 7)

  acerEXTEND does not load on the computer (Windows 7/10). Error message says I need to be administrator. Computer said that I am logged on as administrator.

  Good to hear it!

• My dell optiplex 740 will not start. The screen is black, once it displays the Dell logo. It does not say that the computer is in mode 'sleep'.

  My dell optiplex 740 will not start.  The screen is black, once it displays the Dell logo.  It does not say that the computer is in mode 'sleep'.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You receive an error message?

  Method 1

  See the articles below and check if it helps.

  Computer stops responding with a black screen when you start Windows XP

  http://support.Microsoft.com/kb/314503

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

  Method 2

  I suggest that you start the computer in the last good known Configuration mode and safe mode, post back with the result.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  How to fix a computer that does not start

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/how-to-fix-computer-that-will-not-start

  Method 3

  If the computer can boot in any mode, then I suggest that you perform the clean boot procedure and check if it helps.

  It is possible that some third-party programs installed on the computer is causing the problem.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Sound does not work on my computer and the 'secret' is not on. HE WORKS AT HIOME WHEN PLUGED IN MY SPEAKERS... IAM NOT HOME NOW GET OUT ON THE ROADL

  My sound does not work on my computer... It worked when pluged in my speakers at home... I'm not at home so no speakers and I can not get any sound. I checked mute and is not clicked on also the volume upward all the way. What else can cause the sound works do not? Help is greatly appreciated.

  BJ Gawle

  Hi B.J.Gawle,

  Method 1

  Looks like you're using a laptop and this would happen if the default audio device is not set to internal computer speakers.

  (a) open the Control Panel.

  (b) double click on the sounds and Audio devices icon.

  (c) click the Audio tab and under audio playback, select the audio device on the laptop.

  (d) click apply and restart the computer, check to see if it helps.

  Method 2

  If fails it above step then check out the link below and run the Fixit tool available, check if it helps.

  Diagnose and automatically repair audio playback problems

  http://support.Microsoft.com/mats/AudioPlayback/

• Windows detects the USB key, but it does not appear in 'my computer '.

  When I insert the USB, windows doesn't detect the same, but the icon does not appear in 'My Computer', or anywhere else and I can't use the USB.

  The best diagnostic page on the web that I found for USB Pen Drive problems such as what you have is the following:

  <>http://www.Uwe-Sieber.de/usbtrouble_e.html >

  HTH,
  JW

• iTunes does not work on my computer

  iTunes does not work on my computer it says only: %AppData% not found

  Hello

  Follow the information from apple to the link below

  Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  http://support.Apple.com/kb/HT1923

  and or ask for their support of itunes

  http://www.Apple.com/support/iTunes/

  Also try the discussions of apple itunes

  http://discussions.Apple.com/category.jspa?categoryID=149

• No wireless networks not found on laptop - the WiFi windows service does not work on this computer

  Hello

  I have a laptop model Toshiba P205-56347 running Vista home premium and a lynksis WRT54G V8 router model.  The WLAN light is solid and the internet light flashes on the Linksys.  I have Comcast cable as my ISP.

  I've seen reported similar problems.  All of a sudden my wirless acess stopped working, some networks are displayed and I get the message 'windows wireless service does not work on the computer.  I am not able to restart the windows wireless.  I can't connect to the internet on the laptop.  I have a DELL PC and can access the internet here if necessary.

  In the network and Discovery Center, I see that network discovery is disabled.  I can't set it to on.

  Under system devices, I have the following network cards: Intel (r) Wireless WiFi Link 4965AGN and Realtek RTL8101 Family PCI - E Fast Ethernet NIC (NDIS6.0).

  Help, please.  I'd appreciate any help.  I need a good starting point for resolution and wouldn't start using suggestions that corrects other issues.  I design financial systems and purchase online, but I'm not a technical person with regard to updates Vista, drivers, etc..

  Thank you! After reviewing the responses to similar problems, can anyone suggest if I should try one of the following values: 1. run SCF/scannow at the command prompt I don't know what that's going to fix it and do not want to make the current problem worse. 2. download the driver for the network drivers. If you would be grateful if someone could help me find the driver and download it. 3 reinstall Windows Vista Home Premium SP1 since the restoration of Toshiba CD I would appreciate greatly any information. Donna

  Hi blondswede,

  You can try running sfc/scannow to see if you have corrupted files. That won't be a further problem on your pc. After that, you want to make sure you have the latest drivers for your laptop, especially drivers of the NIC (network card). Go to the following link to Toshiba for your model and download those:

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/modelContent.jsp?CT=SB&OS=&category=&MOID=1757721&RPN=PSPB3U&modelFilter=P205-S6347&selCategory=3&selFamily=1073768663

  If you're still having problems, and it has recently emerged as a problem, you can try to restore your system to a point in time before the problem started to use the system restore. Here are the steps to follow:

  • 1. Click Start, type system restore in the search box, and then click System Restore in the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue.
    2. In the System Restore dialog box, click on choose a different restore point and then click Next.
    3. In the list of restore points, click a restore point created before you started having the problem, and then click Next.
    4. Click Finish.

    The System Restore tool

    If the problem you are experiencing started occurring recently, you can use the System Restore tool. Using this tool, you can restore the computer to an earlier point in time. The tool using System Restore may not necessarily help you determine the problem. When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

    To restore the operating system to an earlier point in time, follow these steps:

    The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Let us know how it works and if you need additional assistance.

  Dave D
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why any screen recorder does not work on my computer? __

  Why any screen recorder does not work on my computer?

  Hi I formatted my computer and downloaded all the conditions for this, I downloaded hypercam and installed, I tried to open it in the tool bar and the start menu, it still does not work.
  I downloaded another program for recording of the screen, it also did not work, I tried 3 programs, they all did not work
  by the way my computer: windows vista service pack 2 and the screen recorders have worked before I formatted my laptop
  I need a solution pleaseeeeee

  I got this error in the three programs

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: ScreenVCR.exe
  Application version: 1.5.34.0
  Application timestamp: 2a425e19
  Fault Module name: StackHash_b4c3
  Fault Module Version: 0.0.0.0
  Fault Module Timestamp: 00000000
  Exception code: c0000096
  Exception offset: 02e42a3b
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1033
  Additional information 1: b4c3
  More information 2: d2a8bebd21e0e9bfa99e084d53ece2b6
  3 more information: 74a 3
  Additional information 4: 0480b6e0a2e7a1df44ee618ae8d0084f

  Read our privacy statement:
  http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409

  Please give me a solution... :(

  my laptop computers Info

  Windows is Windows Vista Home Premium
  Intel (r) core (TM) 2 Duo CPU 26500 2.10 GHz
  3.00 GB RAM
  Mobile Intel (r) 4 Series Express Chipset Family

  =============================================
  Just a thought... maybe your video driver or DirectX needs and update?

  Have you tried the following applications:

  (1) Windows Media Encoder 9 Series
  http://www.free-codecs.com/download/Windows_Media_Encoder_9_Series.htm

  Direct Download Link:
  http://www.free-codecs.com/download_soft.php?d=571&s=327

  First steps with screenshot
  Using Windows Media Encoder
  http://www.Microsoft.com/windows/windowsmedia/HOWTO/articles/ScreenCap.aspx

  (2) Microsoft Expression Encoder 4
  http://www.Microsoft.com/downloads/en/details.aspx?displaylang=en&FamilyID=75402be0-C603-4998-A79C-becdd197aa79

  Expression Encoder training videos
  http://expression.Microsoft.com/en-us/cc197144.aspx

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.