my computer asks me to fix a problem with the graphics driver intel but windows tells me solution can not be downloaded

computer crashed and rebooted itself. I first started in safe mode, and the computer did not find any problems but had sent a report anyway.

To restart normally, the center of the action (or as I would say, Center!; - p), has been asking me to scan with windows defender and a problem with the graphic driver intel. Scanned well, but to solve the problem, said action solution Center could not be downloaded. I am most definitely connected to the internet and have tried to solve this question many times during approximately the last 18hours?
Help would be much appreciated?

Good suggestion but I tried this, had to go the manufacturer of the laptop, but still no luck. Think he was playing tricks on me in any case, as seemed to be resolved with a full audit of the system and diagnosis.

Thanks for the effort though...

Tags: Windows

Similar Questions

  • a problem with the graphics driver intel?

    I click on solve problem in windows 7, and it tells me this

    This solution could not be downloaded most likely causes:

    • Your computer was unable to download the solution at this time. Make sure that your computer is connected to the Internet and then try to download the solution later.

    Install the latest drivers:

    32 bits:
    http://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=19333&lang=eng

    64-bit:
    http://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=19336&lang=eng

    This should fix all the problems.

    I guess, that the action center solution gives you the same advice.

    André

    "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

  • Satellite M30 - problem with the graphics driver and Quicktime movies

    I just installed a 40 GB to 80 GB hard drive and installed all the drivers in the correct order, as indicated by toshiba. Everything works well except the used for Quicktime .mov files. All I get is audio but no image - other than a colorful blur screen!

    I think I've isolated the problem to the graphics driver. Whenever I turned off / uninstall the driver dedicated for the graphics card FX 5200 GP (version 4.6.44) Quicktime files work fine. It is only when I installed the dedicated driver problems occur!

    Can someone tell me why this might be?

    Hello

    Do you use the graphics driver from the Toshiba driver page?

    Try to use the QuickTime Alternative 1.77. In this version the codex QuickTime has been updated.
    This version uses these features:

    -Media Player Classic [version 6.4.9.0 + SVN build 2006-12-24]
    -Codecs QuickTime [version 7.1.3.100]
    -QuickTime plugin for Internet Explorer
    -QuickTime plugin for Opera/Mozilla/Netscape
    -Extra plugins for QuickTime
    -QuickTime DirectShow parser
    -Wrapper DirectShow QuickTime decoder
    -CoreAVC 0.0.0.4
    -CoreAAC 1.2.0.575

    check it out...

  • Problems with the graphic driver for Elitebook 8460p

    Hello

    I m of the problems with the Elitebook 8460p driver display. The latest version (15.28.20.64.3347), published on 16 June 2014 have some problems on the laptop. When the laptop is running on battery screen suffers from flicker and damaged graphics, as you can see in this video:

    https://www.YouTube.com/watch?v=gQ1w0aOaF7A

    (you can see the flickering between 0:20-0:22)

    I contacted with support local hp and send me a COMPUTER technician, who has changed my motherboard and CPU, but nothing worked. I tried to contact with intel for support (the issue is present with drivers intel non - oem), but they are sending me to the OEM. I would like to have a real driver that works with the system (3347 is a driver of the year), is it possible?

    This isn´t of question at all in linux drivers, more change motherboard I totally ignore a hardware problem.

    I can provide feedback to any solution.

    Thank you!

    Another update:

    Found a solution to this thread (which I started) in the forums of intel:

    https://communities.Intel.com/thread/48327?start=0&TSTART=0

  • Qosmio X 300-problem with the graphics driver

    Greetings,

    My X 300 has worked very well and I am using 186 drivers of Toshiba (Windows 7) and completely by the book. Now, my computer is start planting as much UNLESS I have uninstall the graphics drivers from Toshiba, because then it is stable. Sometimes the driver resets, the computer sometimes go to BSOD immediately (he does eventually in any case). Thus, for the moment, it has no driver installed, but driver VGA standard that comes with Windows 7.

    The question is what do I do? A X 300 without proper graphics drivers is a sports car with pedals.

    Any input would be much appreciated!

    Best regards
    Johan

    PS. the warranty has expired, so no free service.

    Hello

    Have you noticed the same problem on Vista preinstalled Toshiba version?

    At the moment, I can t imagine that the display driver itself is really the problem because pilots are pre-tested by Toshiba and I didn t has seen similar topics here in the forum about display driver not work. Maybe another program is causing this problem

    What you can do is to test the Qosmio X 500 display driver. There is a newer version. You should check this.

    By the way: since when did you notice this problem? I ask this question because a restore of the system to an earlier point could also be helpful

  • problems with the graphics card after installing windows 7, code 43

    I installed windows 7 & my ATI-RADEON XPRESS 200 SERIES is stopped by windows 43.It code stipulates that drivers are ok... but it is not recognized... I also downloaded a few 3d Screensavers & they worked very well now, it is not able to open the screensaver because of the video card or to be compatible with Direct 3D... This question has not pop up until after you have installed windows 7, I have checked & found a lot of problems with windows 7 & ATI-RADEON XPRESS 200 SERIES drivers or recognition. Tried to update the driver but the States, it is far, but windows 7 is having a problem with drivers... Y at - it a fix for this, looks like it should be a matter of windows & microsoft should have action corrected problem because windows is caused this problem... Have installed all windows updates & all up to date... Can someone try to give me a solution to fix this problem? Not sure if they have an upgrade or accelerator program 3d graphics that may have to be installed... & again thanks if anyone can help... Have a great day...

    ATI-RADEON XPRESS 200 SERIES is an accelerator of limited DirectX 9 graphics (integrated graphics), which was

    published in ' 07 and apparently is not compatible with Win7.

    Old hardware with a Windows version compatibility isn't something that never gets fixed by SM.

    It is the mfg of the material to support the product through a driver updated, and trend of integrated graphic card

    not be supported as long as a dedicated graphics card.

    In this case support drivers apparently stopped with Vista.

    If you try to get drivers via Device Manager or Windows Update they can provide incorrect information

    What about drivers who are up to date.

    These two methods are a little known does not install the proper drivers for the graphics.

    I read that some people have had luck on Win7 with the Vista drivers for various materials. Doesn't hurt to try.

    You can download the drivers for XPRESS 200 SERIES from the AMD website below-

    http://support.AMD.com/en-us/download

    .

  • I have a problem with the graphics driver.

    Original title: someone help?

    Hello. I have a problem. my laptop says vga graphichs adapter cannot start. I have downloaded the driver and I looked at the Device Manager and there is always problem here.  I clicked the button to update and I chose the folder and it says that the best version of this driver is already installed. But still the same problem... I installed Just cause 2 and it says error directx (code 15) but my video card is compatible with directx10 but I can't open it. My graphics card is nvidia geforce 9300 m and my computer laptop sony vaio vgn-z46gd help me please

    Thierry,

    I would like you uninstall and reinstall the drivers and check.

    We know if that helps.

  • What is the problem with the game of solitaire in windows 7? It does not pick up the cards automatically all the time unless you click on the green background.

    I find the new Solitaire is very poor.  When it must be picking up cards that are exposed and for which the lower value cards have already been placed on top of the Ace.

    Basically, this program is very slow on my new Windows 7-32 computer, and you must click all around the green background so he can have the cards on top of the Aces correctly.

    Thank you

    Ron

    Hi Ron,

    You can try the following steps and check if it helps:

    Method 1:

    We can refer to the computer or the device manufacturer's Web site and try to install the latest version of the drivers for graphics cards.

    Update drivers: recommended links

    Method 2:

    If the problem persists, then try to reinstall the game by following the steps described in the previous post.

    For more information, see the link:

    Turn on or off Windows features

  • HP Support Assistant unable to fix a problem with the CD/DVD not detected

    I have a G42-415DX laptop and I can not read cd/DVD, it was working fine 3 weeks ago and now nothing / I tried the support assistant and he could not solve the problem.  I got a message saying the driver must be reinstalled, how do I reinstall the driver?

    Hello

    If you do not get the chance to use another PC, I would definitely create the CD and the DVD bootable as it would give a clear indication if there is a hardware problem with the optical drive.

    In the meantime, try following the procedure in the title of the subheading "Let me fix it myself" on the link below to remove upper and lower filters (if these registry keys exist) and see if that helps the issue.

    http://support.Microsoft.com/kb/982116

    If find you the following registry keys and delete them, restart the laptop before checking the disc.

    Kind regards
     
    DP - K

  • I have a problem connecting the Netgear model No. RPV3000 Extender. So I can not see my network_EXT computer and therefore cannot link to this Netgear

    I'm AT & T PACE router connected to Internet. However, I have a problem connecting the Netgear model No. RPV3000 Extender. So I can not see my network_EXT computer and therefore cannot link to this Netgear. I tried to use another network with the name of my network_ext and provide the same passkey that my router, but it was impossible to connect to the Extender.

    I would appreciate it, if I can get any suggestion/help to bind and connect to this extension of NETGear. I have WIndow7 system on my computer.

    Thank you

    Harshad João

    First, make sure that the netgear device is not a router.  An Extender is very good.  You can't have more than one router in a network.  Also make sure that if you use the router wireless integrated into your modem, the router ONLY in use.

    There is a very specific configuration for the Extender.  It should have come with detailed instructions.  If you can't find them, call Netgear for assistance.

  • Error message indicating the problem with the monitor of devices in Windows XP.

    Original title: Device Monitor

    Error message indicating the problem with the monitor of devices in windows xp. How to fix?

    Hello

    1. when exactly you receive this error message?

    2. What is the brand and model of your computer?

    3. What is the exact error message that you receive?

    Please provide us with more information about the issue so that we can provide you with the necessary assistance.

  • Problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

    Am having problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

    * original title - I'm having a problem *.

    You have the latest drivers?
    http://www.nvidia.com/page/support.html

    Aero - Windows 7 - How to troubleshoot problems with Aero

    (1) first of all, click on the Start button and type in Aero. Now, click on find and fix problems with transparency and other Visual effects of link.

    (2) a new Wizard dialog box opens. Make sure that you click Advanced to solve all problems automatically.

    (3) either the problem will be solved or not. If this isn't the case, you will get a list of items that are potential problems.

    (4) If you want to see more details about the problem, you can click View detailed information. This will give you a list of potential problems that have been verified and those that pose problems.

    If it does not---> click Start---> right click computer---> click Properties

    Click the link for 'Windows performance index' and then click 'rerun the assessment"to refresh your WEI score and try again.

    Note: If you have Windows 7 Starter, or if your system does not meet the requirements for Aero you will not be able to use Aero.

  • "A problem with the display driver.

    Recently, I get an error message whenever I open Photoshop CS4. It reads as follows.

    "As Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

    "GPU improvements can be enabled in the Performance preferences panel."

    I checked the graphics cards in Device Manager, and when I tried to update the software, it told me that I was aware.

    • OS: Vista Edition Home Premium
    • Dell Inspiron 1520
    • Display driver: NVIDIA GeForce 8400 M GS

    Sincerely, Danny

    Hello

    Try to update your display manually driver and do not use the analysis of the drivers on the manufacturer's website either.

    This is my generic how updates of appropriate driver:

    This utility, it is easy see which versions are loaded:

    -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
    each driver in the list, additional useful information is displayed: load address of the driver, description,.
    version, product name, company that created the driver and more.
    http://www.NirSoft.NET/utils/DriverView.html

    For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
    Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
    video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
    cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
    This will refresh the driver stack.

    Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
    own the software and drivers and all other main drivers that you have.

    Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
    (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
    updates on the site of the manufacturer of the system here.)

    Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

    Always check in the Device Manager - tab drivers version you install actually shows up. This
    because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
    pilot - reboot - check that it is installed and repeat if necessary.

    Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
    This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
    questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
    manually if you wish.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    Hope these helps.

    Rob - bicycle - Mark Twain said it is good.

  • I get the message: Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

    Photoshop has been giving me the warning:

    Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

    Also other programs are affected.  I suspect a recent download of Adobe.  Can anyone HELP.

    No, it has nothing to do with updates of Adobe. There is a problem with your video card driver.

    Go directly to the Web site of the manufacturer of the GPU for updates (not Microsoft, not a System Builder).

  • Photoshop has encountered a problem with the display driver

    I've updated photoshop on my mac last night as it kept prompting me to do, and I have an exam tomorrow, which requires the use of photoshop. When I open photoshop this morning the following message appears:

    "Photoshop has encountered a problem with the display driver and has temporarily disabled the improvements using graphics hardware. Visit the Web site of the manufacturer for the latest version of the software. For more information, visit: http://www.adobe.com/go/photoshop_gpu_cc_en'. '.

    Can someone help me with this? IT IS URGENT!

    The problem is the driver for your video card, no Photoshop.

    Update the video card driver from the website of the manufacturer of the GPU (NOT Microsoft or a system integrator).

Maybe you are looking for

  • Code 19 device fingerprint scanner

    Hello I recently lost the use of my cell phone on my HP Envy 15-j092nr fingerprint reader. I get a code 19 for sensors of validity under biometric devices in the Device Manager window and I was wondering how I can get it working again. I tried a few

  • issue of vifindrsrc

    status = viOpenDefaultRM (& updateSession);status = viFindRsrc (updateSession, "GPIB0? * INSTR "(, & FListe, & numInstrs, desc);"If (status{viClose (updateSession);}{while (numInstrs)-}viOpen (updateSession, desc, 0, VI_NULL, & updateName);viClose (u

  • After factory reset saved Documents unintelligible notebook

    Running Windows Vista 32 - bit family Basic (Version 6.0.6000) I recently had to reset my OS to factory conditions, and one of the (many) problems I got so far is the fact that some of my notebook documents stored on my external hard drive first open

  • Board of Directors

    HP g60 power supply problem

  • Character animator error AIF/OpenGL. Update drivers does not. With the help of Intel HD 3000.

    What should I do? I have my drivers up to date with the latest versions of 2015 and I still get the problem as soon as I click a puppet (which of course does not show). Is this in relation to my video card?I run Windows 7 Edition home premium SP1, In