My computer is stuck in power saving mode

Hello. I need your help guys. My computer won't come out of power saving mode. I was chatting with someone on MSN and light of my computer went from blue to orange and my screen went black and I got the message "power save mode, press any key or move the mouse to leave". I pressed all the keys and moved the mouse, but it wouldn't leave the power saving mode. I unplugged my computer and I even changed around the RAM cards. I took the CMOS battery and tried. Nothing has worked. I also took my videos and my graphics driver cables. Still, he doesn't after that I put everything in place [except the drums]. Recently, I put the battery back in and it still doesn't work. I dusted off my gear inside my computer and cleaned the fans. There is this light inside my orange computer as soon as I put the power cable at the back of my pc. I don't know what to do. It's so frustrating. I need your help! Here are a few photos from my computer (Dell Inspiron 530 s, A).

1: http://tinypic.com/r/28vwufp/7
2: http://tinypic.com/r/dwvzhz/7
3: http://tinypic.com/r/1444ojt/7

Here are the pieces of vaues for numbers of image 3:
1 - socket processor (CPU)
2 - connector (CPU_FAN) CPU fan
3 - connectors (DIMM_1) memory
4 - connectors (DIMM_2) memory
5 - connectors (DIMM_3) memory
6 - connectors (DIMM_4) memory
7 - main power connector (ATX_POWER)
8. Jack battery
9 - connectors (SATA0) SATA drive
10 - CMOS jumper (CLEAR CMOS)
11. password jumper (CLEAR_PW)
12 - connectors (SATA1) SATA drive
13 - connectors (SATA4) SATA drive
14 - connector (F_PANEL) front panel
15 - connector (F_USB1)
16 - connectors (SATA5) SATA drive
17 - connector (F_USB2)
18 - modular connector (F_USB3) before
19 - front audio (F_AUDIO)
20 - connector (PCI2) PCI
21 - connector (PCI1) PCI
22 PCI Express x 1 Connector (PCIE_X1)
23 PCI Express x 16 connector (PCIE_X16)
24 - audio connectors
25 - 2 USB and 1 LAN connector
26 - 2 USB connectors
27 - connector (CHASSIS_FAN) chassis fan
28 - video connector (VGA)
29 - power supply of the CPU (ATX_CPU)

Thanks for your help in advance!

E-mail: * e-mail address is removed from the privacy * [contact if we need to discuss.

Hi xxbrgxx,

You can see the steps mentioned in the links of dell under which addresses question power saving mode

http://support.Dell.com/support/eDOCS/monitors/1901FP/en/trouble.htm

http://en.community.Dell.com/f/3529/t/17144276.aspx

If the problem persists, contact dell for assistance more specialized on this issue.

http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

Thanks and greetings

Ajay K

Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

Tags: Windows

Similar Questions

  • Computer keeps going into power saving mode

    Hello, I'm fighting with my pc it keeps going on the power saving mode how to stop what I sometimes lose my job

    Original title: URGENT
    Moved from the community involvement Center

    Disable saving energy mode in Windows 10

    1. Click Start
    2. Type power and press ENTER to open it
    3. In Option of power--> the window on the right panel under ' choose or customize a power pan "selected Plan is a balanced.
    4. Then click on change plan settings
    5. This will open the Edit plan setting window
    6. To turn off the screen FOREVER in both batteries & Plugged In
    7. Make sure you put the computer to sleep FOREVER in both batteries & Plugged In
    8. Then click on save changes
    9. This will save it, and you're done!

    Note:

    1. Battery: It will accordingly when the system is on battery Mode (load is not Plugged)
    2. Plugged in: Will accordingly when the system is Plugged In to the wall (the charger is plugged in)

  • My computer keeps going into power saving mode and it is not configured for it... What can I do

    My computer guard shut down in power save mode... I installed everything that has been suggested to correct this, but nothing works

    Read the documentation that accompanies and/or to communicate with the computer manufactures Technical Support.

  • How can I activate the remote computer to power saving Mode monitor?

    I am a technician in a small private company and it is my duty to keep all desktop computers works very well.
    Desktop computers:

    • are the Dell Optiplex GX260
    • Run Windows XP SP3
    • have Dell 17 "monitors
    • with Intel Pentium 4 (2.4 Ghz) processor with 1 GB RAM

    I do my job after working hours. I connect to them with my laptop (running Windows 7) and check their conditions, one by one. Now, my employer comes to know that when I do this whole process monitors for desktop computers continue to run. As it is not put in place a very large company and electricity and the price of fuel in Pakistan are very high. So, he asked me to find a way to turn the monitors to the power saving mode, when I do my work. In this way, it will be significant energy savings and fund savings in monthly bills. So, can someone please tell me How do I turn on monitor of the remote computer to the power saving mode?

    There are several ways to handle this.

    #1-have affected the power turn on their monitors, but let run PC
    #2-click Start > Control Panel > Power Options and choose how long it is before the screen turns off. Once your activity on their machine is complete, then will kick time.
    #3-you say that you connect to their machines to check their conditions... whatever that means exactly. You can map their computer management console directly to your machine and I * think * he didn't wake up the monitor.

    I hope this helps.

  • computer freezes and goes to power saving mode

    Several times a day my computer freezes and goes into the power saving mode.

    Hello
     
    1. have you made changes on the computer recently?
    2. do you use a particular application when your computer crashes?

    Method 1.
    Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
    Step a. refer to the article below for the procedure safe mode in Windows XP
    A description of the options to start in Windows XP Mode
    http://support.Microsoft.com/kb/315222
     
    Step b. You need to perform a clean boot to find the program that is causing and then disable or remove.
    How to configure Windows XP to start in a "clean boot" State
    http://support.Microsoft.com/kb/310353/en-us
    Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

    Method 2.
    Also, check the logs of the observer eveny for recent activity on your computer and check.
    This article describes how to use Event Viewer to view and manage the event logs in Microsoft Windows XP.
    Procedure to view and manage event logs in Event Viewer in Windows XP
    http://support.Microsoft.com/kb/308427
     
    I hope this helps.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.
    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Computer runs continuously check disk and automatically goes into power saving mode.

    2 days ago my computer was working fine, then yesterday he wanted to run the check disk at startup upward. Finished, he found no errors and proceeded to vista loading which then stated that he was going to power saving mode, the screen went black and clear screen turned yellow. Now he wants to run the check disk on every restart and ends with her past in power saving mode. I've only got 1 successful start since this all started. I tried to start in safe mode but it freezes. I also tried to boot to the last known configuration but that only prompted an another disk check and ended just as vain as other attempts. The hard drive is only a year so it should not be failing already. I don't know what I should try. Any help would be greatly appreciated. Thank you!

    Hello

    1. have you made changes on the computer recently?

    2. What is the brand and model of the computer?

    Method 1.

    Open an elevated command prompt. To do this, click Start, click programs, accessories principally made, right-click Guest, and then click Run as administrator.

    The correct way to disable CHKDSK to start use the on command chkntfs /x switch in command prompt. The /x switch will exclude a verification by default startup car. If you have drive C: as your hard drive, then the command to disable chkdsk C: drive analysis would be:

    chkntfs /x c:

    If you have 2 drives C and D, you can disable chkdsk with the command below

    chkntfs /x c: d:

    So go ahead and restart.

     

    Method 2. 

    Registry warning

    To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    322756 (http://support.microsoft.com/kb/322756/)

    How to back up and restore the registry in Windows

    Here are the steps to disable checkdisk at startup.

    1 - click on the 'Start' menu of Windows on the desktop and click on "Search" (Windows Vista or 7).

    2. Type "regedit" in the search box and press 'Enter' to start recording.

    3 - Click on '+' in the folder 'HKEY_LOCAL_MACHINE' to develop. Click on the 'SYSTEM' folder and click on the folder "CurrentControlSet". Click on the 'Control' folder and then click on the "Session Manager" folder.

    4 double click on 'BootExecute' on the right pane. You should see the default value of the key defined as autocheck autochk * (with asterisk). The asterisk (*) means that the Windows controls every drive for consistency. Add "/ K:C" at the end of the autocheck autochk * after the addition, the final value should look like this: autocheck autochk / k: C *.

    5 - Click on "file" and click "Exit" to close the damper. Restart your computer. The disk check is no longer lance to the computer startup.

    Method 3.

    After the checkdisk has been disabled, I suggest you to reset the power to the control panel settings and check if that helps.

    Solve power problems: http://Windows.Microsoft.com/en-za/Windows-Vista/troubleshoot-power-problems

    Change, create, or delete a power plan (scheme): http://windows.microsoft.com/en-us/windows-vista/Change-create-or-delete-a-power-plan-scheme

    I hope this helps.

  • Updates made now computer won't start and power saving mode

    After going through the procedure that I received the usual message "loading down updates 1 of 9 please don't turn off your computer ' closing, so I left and went to bed. The next morning, but when I turned on my computer as it has been commissioning a box came on my screen "power saving mode" and entering power saving mode nothing happens. I then turn off my computer and then put it again by pressing F8 I hope go to the options of allowing me to boot in safe mode so I can take it from there. However, this does not work and once more, he'll just right to the power saving mode and is right. Y at - it someone who has ideas for what to do. I am running Windows Vista, if this is useful.

    Hi FrankSpencer,

    Follow the steps below and see if they help.

    Step 1:

    Do Startup Repair from the windows installation disc and check that if it helps, here is the link:
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

    Step 2:

    If this does not help, you can do a System Restore from the system recovery options.

    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • How can I configure my computer to it won't go into power saving mode every 2 min

    How can I configure my computer to it won't go into power saving mode every 2 min

    How can I configure my computer to it won't go into power saving mode every 2 min

    Change the configurations screen saver and hibernation / sleep appropriate for your desires.

  • U2414H, Macbook Air, waking up to the power saving mode

    When my MacBook is sent to sleep or I shut down the computer, the monitor will sometimes get stuck in a loop where he wakes up "Power Saving mode" then displays "Enter Power Saving Mode" then shut off again and repeat in less than a second. Also while I was trying to open the OSD menu to check if the resolution is set correctly (as described in validation) capacitive buttons are just hard does not work. Hope you can help.

    Serial No.: CN-0H8H7G-74261-46 b-36GL
    Revision A01
    Included computer: MacBook Air mid-2014 connected via mini-DP to DP cable
    Intel graphics card internal HD5000
    Run monitor to 1080 p 60 Hz

    The air doesn't have a DP (DisplayPort). It uses Thunderbolt. So, how you connect to our RFP U2414H?

    Unfortunately, Dell does not validate the test / this model of monitor on Apple, ports and software hardware. For this reason, Dell has no troubleshooting steps a lot to offer. You can post on the Forum of Discussions Apple and see what they say. Some apple users have mentioned using a bolt of lightning to HDMI adapter or love at first sight for adapter DP has had some success.

    Apple computer thunderbolt port--> crush on HDMI adapter--> Dell HDMI to HDMI Cable TYH2W, W69C3--> Dell monitor HDMI port

    Apple computer thunderbolt port--> crush on CDM--> Dell DP DP adapter cable--> Dell monitor port CDM

    Apple computer thunderbolt port--> maid in CDM adapter--> Dell mDP to DP cable--> monitor Dell DP in the port

    You have the latest version (11 June 2014, A01). Users of Windows 8/8/1 under their power management windows computer balanced high performance which fixed some issues wake-up call. Windows 8/8.1 on balanced allowed the DP computer to go to sleep. He confused the handshake of DP at the end of the screen. Have you tried to test with DP1.2 disabled in the OSD menu?

  • Satellite A200-1IZ becomes extremely slow using the power saving mode

    Hello

    Since I installed windows 7 I can't use my computer in battery saving mode because it becomes extremely slow.

    It takes so long for trivial tasks. It is virtually unusable.

    Can anyone tell me the reason for the problem and if there is some sort of solution?

    Thank you.

    Hello

    What performance maximum CPU you have for the power saving mode? Check the Windows power management settings: start > Control Panel > Power Options.

    The plan for the power saving mode settings and make sure that the maximum performance of the CPU is at 100% for the power saving mode. This increases the performance of the computer.

  • My laptop goes into power saving mode after one minute. Someone knows why?

    It's just started happening yesterday. I use a Toshiba laptop and out of nowhere, my PC goes in power saving mode after one minute when ALL my settings for this mode is 30 minutes. Does anyone know how to fix this?

    Hi MattLipkint,

    1. Did you the latest changes on the computer?
    2. When was the last time it was working fine?
    3. You have security software installed on the computer?

    Method 1

    It is possible that some third-party programs installed on the computer is causing the problem.

    I suggest that you put the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See section to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    (a) click Start, type msconfig in the search box and press ENTER.

    (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

    (c) under the general tab, click the Normal startup option, and then click OK.

    (d) when you are prompted to restart the computer, click on restart.

    Method 2

    If the previous step fails then I would suggest that you update the display adapter drivers, basic input/output system (BIOS) and motherboard chipset drivers.

    Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    How to manage devices in Windows XP

    http://support.Microsoft.com/kb/283658

    How to solve the problems of hibernation and standby in Windows XP

    http://support.Microsoft.com/kb/907477

  • My Dell is power saving mode and will not come out

    My Dell is power saving mode and will not come out? Any suggestions? I can't get anything else than a screen that says it is in power save mode and press a key or move the mouse. No one who does nothing. Don't disconnect.

    Hi Ma32206,

    Monitors Dell will automatically mode energy saving after a predetermined time amount when the computer is idle. The Dell monitor will go completely black, rather than display a screen saver. This allows your monitor to essentially turn off until it takes again.

    A. Press any key on the keyboard or move the mouse. Either will automatically turn off the power saving mode. Alternatively, you can press the power button on your Dell computer tower or laptop.

    B. press one button a second time if the monitor goes power saving in standby mode. Standby mode allows the screen saver appears.

    Bindu R - Microsoft technical support.
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Dell monitor U2715H Power saving mode by turning on PC

    Hi, I had a constant, frustrating problem with my Dell U2715H monitor. I connect it to my PC using CDM, and absolutely 100% whenever I turn on my pc, it goes into power saving mode. The only way to get my computer is to force power off of my PC now the power button and then turning it back on. This recovers no mode 'sleep', but an engine out of State. I tried to turn on/off the screen first, wait a minute then turn the PC. I tried to use the usb mouse and keyboard only to the back of the computer and not on the monitor ports. I tried all of the solutions presented to me in the troubleshooting of energy saving guide, but I am completely off options and frustrated. I don't want to force shutdown my PC every day just to get the monitor to work.

    Please help with the troubleshooting methods that I could take to solve this problem.

    I really love this monitor otherwise and won't have to return it.

    WOW! I just talked to a dell technician who accompanied me through the question. Apparently, the problem is known and has been placed on the record. The workaround is desperately single.

    To resolve this problem, click the first button on your screen, then press the second button to access the "input select" menu of the monitor. Then, place the cursor on the entry that you use (for me it was the CDM) and hold the button of checkmark for 10 seconds. A dialog appears asking you to turn on/off 1.2 DP. Once you enable it, the Monitor refreshes and the issue is history.

    I guess that the monitor has some secrets, I don't know... Hope this helps someone out there with this problem.

    Dan

  • Monitor Dell Vostro 2705 keeps going into power saving mode

    I have a Dell Vostro 2705. When I turn it on, the screen goes into power saving mode. We tried with a different monitor and it still does not work. I do not see there is a separate video card to replace it. Can it be fixed or is - a new computer?

    Thanks in advance for your advice.

    Judy

    Hello

    Its usually a faulty motherboard. So the only option is to get the Board replaced.

    You can try doing a power cycle and if still doesn't work then a replacement of the Board of Directors.

    Concerning

  • UP2414Q, stuck in power save Mode

    Display: UP2414Q
    Connected laptop: Macbook Pro, Nvidia GeForce GT 750 M
    Connected via: Display Port
    Problem: Goes directly to the power saving Mode
    ----------

    Hello

    Monitor worked fine for months. Today I adjusted the brightness up to 30 percent to 50 percent, and then the monitor came into power saving mode directly. Was it just a coincidence or the root of problem that I don't know. I plugged a second macbook, and also an Asus laptop via either the display port, mini display port and HDMI. Monitor also jumps directly into the power saving Mode. Computers and cables work on other screens. If I Plug and unplug the cable from Port of the screen of my laptop, the screen flashes between =
    Power saving mode (when it's plugged in)
    and another message saying: cable NoDisplayPort (when it is not plugged in)

    When I plug the cable from my laptop display flashes to and indicate that it detects a monitor, and I can open a panel of preferences, so that the laptop thinks that the display is there, but appears power saving Mode. Keys on the screen the menu physical don't give me the opportunity to choose an entry, other options available. Any suggestions?

    Kind regards

    Jason

    Dell UP2414Q Rev A01

    MacBook Pro (retina, 15 inches, mi 2014)

    OS X Yosemite / Mavericks

    NVIDIA GeForce GT 750M

    Display Port 1.2

    - - - - - - - - - -

    Hello

    I lived even issues you described. The cause of my problem turned out be the DisplayPort 1.2 cable supplied with my monitor. After that substituting a VESA approved cable, my monitor works fine.

    The damaged cable that it prevented the monitor to receive the full 4K at 60 Hz signal. Which I suppose is the reason why he could detect that it is connected, but cannot display the image. Deactivation of DisplayPort 1.2 authorized of the monitor to display a 1080 p at 60 Hz signal.

    The first issue I encountered was how to disable monitor DisplayPort 1.2 configuration. When I tried to access the screen on, the monitor will only show me the submenu "Input Source". I found that if you hold the four key (which should be the check mark) for 8 seconds, a menu appears allowing you to disable the DisplayPort 1.2. This allowed me to use my monitor until my replacement cable at least.

    Recently, I had upgraded to OS X to Yosemite and thought this might be the problem. However, after testing my machine on a UP2414Q friends, I was able to determine that the cable was the culprit. First of all, I used its power cable and its cable DisplayPort 1.2. Then, my power cable and its cable DisplayPort 1.2. Finally, my power cable and my cable DisplayPort 1.2. The monitor has been able to display 4K at 60 Hz in all cases except when using my cable DisplayPort 1.2.

    Hope it will be useful. I had tried many techniques to reset my Dell monitor and my computer settings, nothing helped. I am pleased that, ultimately, it was a $ 15 million challenge.

Maybe you are looking for

  • The President is not working on Equium A100-338

    Dear forum Support from Toshiba, I was faced with a problem with my laptop Satellite A100-338.I'm not able to use on the enclosure. I tried to play audio / video (CD / DVD) but the President is not functional, no sound! If I connect the headphones, I

  • BSOD on Y510

    Hi guys,. I have a recurrent BSODS after trying to install the drivers for the program "Alcohol 120%". Startup is not getting up to the Vista boot screen, and safe mode ends in the same dilemma. I was wondering if there is a way to fix this problem w

  • Endless loop

    Program being updated to Windows 7 it goes into an endless loop

  • Lost my audio

    3 days after restarting computer win 7 ultimate loses sound / sound card Elit Creative pro. The speaker icon has Red Cross and when diagnose with the app Creative sound card, he says that he has no Creative sound card! Troubleshooting of the model sa

  • Runtime error! Dllhost.exe "this application has requested enforcement in an unusual way.

    At seemingly random times, I get an error window that contains the following information.  I don't know what application it is referring to, as it happens when I have all the apps open.  The title of the window is Microsoft Visual C++ Runtime Library