my computer went non responsive after trying to install windows 7

Similar Questions

• STOP STOP 0x0000008e error error messages appear after trying to install Windows XP on the new drive

  Original title: Stop error 0x0000008e error displayed after trying to install Windows XP on the new drive

  STOP 0x0000008e error. Also setupdd.sys - address F740DFEA base at F73EC000, Datestamp41107c8f. After trying to install Windows XP on a new hard drive. Never been in the BIOS. A bit afraid to change much, but it is said that the caching and shadowing should be turned off and boot into Safe Mode, but I cannot get Safe Mode because there is no OS on the drive. Also, he wants to know if I want to install Windows XP to a partition on the disk. I looked at other readers, and there is a partition, so I think I should. Any information would be appreciated. "Just an old fart."

  Hello

  See the following article: error message "STOP 0x0000008e" during the installation of Windows XP

• HP Pavilion ze4900: blue screen of death after trying to install Windows on Pavilion ze4900?

  After the death of my hard drive in my Pavilion ze4900, I replaced it with another hard drive for laptop, I had laying around.

  I also tried to install Windows XP Home from a Windows installation CD, the same OS, the laptop had before the hard drive died.

  Everything is going well until the laptop has been made all the installation files, instead of giving me the opportunity to install Windows or repair Windows, the laptop will eventually show me a blue screen with the message:

  "A problem has been detected and windows has shut down to prevent damage to your computer.

  What can I do to fix this? I installed Windows XP on another computer using the same CD, so the CD disappeared not corrupted and replacing the hard drive is hardly used.

  Any help would be greatly appreciated!

  @zenvo2015,

  Hello and thanks for the display on the HP support forums.  The first thing you want to check is if there are any problems with the hard drive that you put in.  Run BIOS diagnostics for the drive and the equipment to make sure that there is no problem.

  Laptops HP - diagnostic system (F2)

  And.

  HP Notebook PC - test a hard drive from BIOS

  Please let me know how things are going.

  Thanks again for posting and have a great day.

• After trying to install Windows updates, my computer turns off.

  I tried to load 2012 ARO.   In the end there was a request to restart my computer, so I left closed... it has been slain on the third phase of the judgment since then.  Support ARO said that it's a microsoft issue, not a question ARO.  I tried to restart in SafeMode known last... but who doesn't have a wok.  At out the battery, disconnected it, everything that I could think of and nothing works.  Help, please.

  original title: don't stop after update

  (1) never install two security systems on the same computer because of the possibility of conflicts like this.  Norton may have similar tools to what you were trying to install.

  During the validation of the subjects as that one, don't forget to post your operating system of Windows and the computer make and model.

  Recovery discs are here with your system?  Alternatively, did you create recovery discs?  Have you created a boot disk?

  (2) by changing the boot order, you can force your computer to boot from a CD/DVD drive, a floppy, or even out of the network drive.  Use the startup disk or recovery disk if you have one.

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  If the answer to the above is failed.

  (3) reboot and start typing the F11 key

  Y at - it a recovery screen?

  Follow the prompts

  Select fix my PC

  Description of the Windows XP Recovery Console for advanced users

  http://support.Microsoft.com/kb/314058

  If the answer is still no, you need to get the site of the manufacturer of the computer recovery discs. I think that you will be able to order Windows Vista or Windows 7 but Windows XP is rained on many sites and an internet search may be more useful in this case.

  How to get the installation discs for Windows XP for installation of boot floppies

  http://support.Microsoft.com/kb/310994

  Bing search engine

  http://www.bing.com/shopping/Microsoft-Windows-XP-Professional-with-Service-Pack-3-32-bit/p/7EC2D538C44375E9D976?q=sale%3A++Windows+XP+&lpq=sale%3A%20%20Windows%20XP%20&form=hure

  Recover Windows Vistsa operating system using HP Recovery - (relates as well to Windows XP)

  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=en&cc=us&DocName=c00809678&product=18703

• Bootcamp partition, disappeared after trying to install windows 10

  Hello world.

  I tried to create a bootcamp on my MacBook (13 '' MacBook Pro 128 GB early 2015) and the computer restarted then that partition the drive. The 32 GB, I put in the training camp are now "deleted" from the drive, and I can't find them.

  Please after the release of the next command in OSX Terminal.

  Cs diskutil list

• ESXi 3.5 and when trying to install windows server 2008

  I installed ESXi 3.5 on my server and successfully created a first virtual computer on which I am trying to install Windows server 2008 standard. I use VMware Infrastructure Client 2.5 from a Vista machine to access my virtual machine console.

  Installation of Windows server is an ISO file located in the root directory of the ESX Server data store. Everything went well with the installation until one last server restart showed a screen stating "the password must be changed before logging on the first time' by clicking on 'OK' present a login for 'Administrator' screen, asking me to enter a password for the 'new' and 'Confirm password '.

  Any attempt to enter a new password results (up to 14 characters, mixture letter & number) in a message "unable to update the password, the value provided for the new password does not meet the requirements of length, complexity or the history of the area.

  As far as I know, I'm not usig a specific domain, have never been able to access Windows server 2008 to create an admin account. I don't know how to solve this problem. I am new to VMWare and Windows server 2008.

  Any suggestion to move forward and allow me to have access to the server via the console?

  Thanks in advance for your help, Claude

  This isn't really a problem with VMware, but more of a problem of Windows 2008 password complexity requirements.

  The account that she is not asking that you must change the password is the local administrator account.

  And you have tried in upper case, lower case, numbers and special characters?  Something like Win2008!@#$ maybe?

  Jase McCarty

  http://www.jasemccarty.com

  Co-author of VMware ESX Essentials in the virtual data center

  (ISBN:1420070274) Auerbach

• After trying to install the updates. my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.

  Visa update problem

  After trying to install the updates.  my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.  I tried to follow the instructions provided here because it seemed to be the same problem.  But when I restart and hold down the F8 key so I can boot into safe mode, I tried selecting safe mode and I get the same results, and I tried again by selecting the option 'Disable automatic reboot' which seems to be an option on the same page with the option of safe mode.  Whatever it is, the same message comes back and I can never get to where I can see my desktop to click 'start '.  I can't get out of this cycle.  I installed the update because it said I needed to install it.

  *************************************************************************************************************************************************

  Turn off your computer by holding the power button for about 20 seconds.
   
  Start your computer in safe mode: press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears
   
  Disable the automatic restart in the event of system failure:
   
  • Click Start
  • Click on Control Panel
  • Click on system and Maintenance link.
  • Click on the system link
  • In the left pane, click Advanced system settings
  • Locate the startup and recovery area, click the settings button.
  • In the startup and recovery window, uncheck the box next to automatically restart.
  • Click OK in the startup and recovery window
  • Click OK in the System Properties window
  • Close the system window
   
  After that... While STAYING in safe mode I do a system restore and maybe try a manual install of the update later.
   
  For the sake of space I refer you to the article about how to proceed.
   
  System restore
  http://windowshelp.Microsoft.com/Windows/en-us/help/9f6d755a-74bb-4A7D-A625-d762dd8e79e51033.mspx
   
  Windows updates: http://windowshelp.microsoft.com/Windows/en-US/Help/8f259118-0d61-4c7a-8c56-24987e87a8171033.mspx
   
  Please let us know if this solution works for you

  Theresa
  Microsoft Answers Support Engineer

  Hello

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Computer laptop screen locked after trying to download a free drawing software now can not deactivate or close the screen

  computer laptop screen locked after trying to download free software for drawing fast vector engineer tools and now the break is unable to calculate or close the screen

  Thank you

  Bill

  If your computer is bad, you need to do a system restore. Since it seems that you can not stop, try to hold the power button until it turns off. If this does not work, unplug (if laptop, remove the battery).

  From there on, allows to do a restore:

  1. turn the computer on and start to tap F8 to get the start menu
  2. Select repair your computer
  3. Select System Restore
  4. Follow the prompts

  If the restore point is older, feel free to use the Scan for affected programs feature to make sure that no other programs are affected. Otherwise, I would make a note of it, as it will have to reinstall these programs. In addition, I was running updated Windows once your system working again, since you will most likely use a restore point set up just before an update. (no point in re-opening of a security breach)

• Tecra S11 BSOD after trying to install BIOS v3.1

  Tecra S11 BSOD after trying to install BIOS v3.1

  I have reinstalled all utility fingerprint successfully. After that I tried to install the new BIOS v3.1, but I got the BSOD
  Win 7 pro
  Where can I find the minidump to see what file that are the problem?

  C/windows/minidump folder is empty.

  Hello

  Do you get the BSOD during the BIOS update procedure?
  Are you using the Windows operating system preinstalled Toshiba? or did you install your own system?

  If you have installed your system, then you should check that the VAP is installed as well.

  Also, I found this info about the update to the BIOS:

  + Attention! +

  + Please close all applications before running the update. +

  + At the end of this process, the computer will be restarted in order to update the EC. +
  + While updating the CE, the screen will not appear and the power LED etc can blink. +
  + The computer may restart several times. There is no abnormal behavior. +
  + Please wait until the computer is restarted fully. +

• win xp sp3 restart after trying to install edimax ps-1216u for printer laserjet p1102

  win xp sp3 restart after trying to install edimax ps-1216u for printer laserjet p1102
  I have the printer installed that tried to install edimax ps-1216u and when it tries to install the printer, the computer restarts

  Problem solved! I have disabled smart installation with SIUttility for this computer. I have manually installed the printer by adding the port tcp/ip standard and all is ok now.

• After trying to install word printer epsom has not stopped workung - uninstalled but stll not working not

  After trying to install a printer, Epsom SX130, on Windows 7, WORD has stopped working - have tried uninstall & restore but still cannot use WORD. After paying only £ 65.00 to restore the office, I'm very unhappy. It is the only document that we need to print, others may be sent by e-mail, but now I can't even open Word documents to use as attachments to an email. I'm totally desperate, do we buy a 'small' I wonder. More than 60 years, when I started it, maybe I was just too old or it's Windows 7 just make my / our life uncomfortable for us to update: Please keep in mind, I'm very, very, ridiculous with computers. We have done with a drive by the way if that makes a difference & downloaded an update. If the answer is "not compatible" that's fine, I can make documents on the old computer, BUT need words for emails: i.e. repeat orders etc. which are vital to our system of new physicians.

  Am totally fed up now...

  Hello

  1. what version of Microsoft Office are you using?

  2. you receive an error message when you start Microsoft Office Word?

  You can perform the system restore the computer to the date when the changes were made not (before the date where Microsoft Office was working fine).

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

   

  NOTE: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  For further assistance on the question, you can post your query in Microsoft Office community:

  Microsoft Office community

  http://answers.Microsoft.com/en-us/Office/Forum/Office_2007

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• While trying to install windows xp on my computer, it displays the search for previous versions of windows and then locks the system.

  XP installation problem

  while trying to install windows xp on my computer (processor i3), she shows looking for previous versions of windows and then crashes the system. So please give me a solution

  Hi deva_reddy,

  Looks like you are trying to do a repair of windows xp installation.

  You use a windows installation cd?

  Refer to the link below for the procedure to install windows XP using different methods.

  http://support.Microsoft.com/kb/978307

  Hope the helpfu.

• new hard drive for laptop computer tried to install windows XP

  Just fitted new hard drive for laptop computer tried to install windows XP, continues by saying can not find any hard disk. any help would be appreciated

  Hi JohnJelf,

  ·         What is the brand and model of the laptop?

  ·         What is the full error message?

  ·         The new hard drive detected in BIOS?

  I suggest you to contact the manufacturer of the laptop computer for more help and information.

• I tried to install windows 7 themes for xp and when I restarted my computer it keeps on opening of session and disconnects me immediately.

  I can't log on because of windows I tried to install windows 7 themes for xp

  Hello

  Step 1:

  Check if you are able to boot to the desktop in safe mode. To start in safe mode follow the link given below.

  http://support.Microsoft.com/kb/315222

   

  Step 2:

  If the problem does not occur in safe mode then boot to the desktop in normal mode and check that the third-party program is causing the problem. To configure your computer to clean boot follow the link below.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: When you are finished troubleshooting, follow step 7 in the article to start on normal startup.

  Step 3:

  If this does not help you try to perform a system restore and see if that helps.

  http://support.Microsoft.com/kb/306084

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer will not start after the installation of Windows Vista SP2

  
  After downloding and installing Windows Vista SP2 on ACER laptop for my daughter, I can no longer start the computer.  Initially registered startup C:\\Windows\System32\drivers\ecache.sys as corrupt file repair.  Change BIOS to boot first from the optical drive and the departure of computer with Vista DVD in the drive, I accepted the option repair.  No chance that the machine always fails to start and always displays the window "Statup repair."  Auto repair is always unsuccessful.  Repair suggestions will be appreciated.  Thank you.  Bob G.

  Support Microsoft still offers a FREE support for Vista SP2.  Go to: https://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034&st=1&wfxredirect=1 where they will help you.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.