My D110 has no ethernet port. Other than the wireless, how can I connect to internet?

Similar Questions

• vSphere HA detected that this host is in a network other than the master vCenter Server is connected

  Hi all

  I try to install a vSphere 5.1 environment (vCenter 5.1 (799731))... It has never been so difficult to get a VMware product running.

  
  Problem:

  As soon as I create a Cluster HA (with 2 ESXi 5.1 (799733)) I get the message:

  "vSphere HA detected that this host is in a network other than the master vCenter Server is connected"

  I tried everything...

  vCenter place in other networks

  Multihomed vCenter

  Place the vCenter in the same network as the ESX host

  Doublechecking ip, subnets, gw, name resolution, vSwitches

  nothing done... is this a bug?

  vCenter and also the two hosts of ESXi now resides in the same L2 network.

  ESX1: 10.254.250.74 255.255.255.0

  ESX2: 10.254.250.77 255.255.255.0

  VC: 10.254.250.29 255.255.255.0

  The message may not be correct.

  Please... @ someone out there... Help! I'm at the end of my knowledge.

  Concerning

  Adrian

  You can check the configuration of VLANS on your physical switch?

  Mike

• My default search engine has been on anything other than Google. How to switch this back?

  Somehow my default search engine has been changed to Google to what is called "My Web Search". I want to switch to Google, but I can't figure out how. I disabled the plugin and removed my options of search engine in the top right, but nothing has changed.

  You have My Web Search installed; Look under Tools > Modules > Plugins. He could have grafted in on something that you have installed. Always seek and opt-out when installing other programs and Add-ons that you install from sites other than the site of Mozilla Add-ons. My search on the Web is considered malware/adware/spyware by many. You must remove it.

  Step 1. You can check if you have one of these installed ' Fun Web products ' :
  Control Panel > add or remove programs: Ask.com Bar, my search bar, of the MyWay Bar speed, my search on the Web Bar, Fun Web products Easy Installer
  See:
  http://www.safer-networking.com/removemywebsearch.php
  PC Hell: My Web search removal Instructions
  http://helpint.MyWebSearch.com/intlinfo/help/toolhelp.jhtml#Q3
  http://support.Mozilla.com/en-us/KB/troubleshooting+plugins#Manually_uninstalling_a_plugin

  Step 2 You may need to change a preference to reset your default URL/location bar search engine:
  -Enter Subject: config in the URL/address bar and press the Enter key
  -If you see a cautionary, accept it (promise you'll be careful)
  -Filter = keyword.url
  -Under the filter, right-click on the keyword. URL and choose "Reset".
  -Restart Firefox (file > restart Firefox)
  See: http://kb.mozillazine.org/Keyword.url

  Step 3 You may need to reset your homepage. Firefox can open multiple home pages. Home pages are separated by the ' | ' symbol.
  See: http://support.mozilla.com/en-US/kb/How+to+set+the+home+page

  Other topics: ~ ~ Red: you have installed the plug-ins with known security issues. You must update them immediately. ~ ~

  You ~ ~ Red:PEUT~ ~ need to update Adobe Reader for Firefox (aka Adobe PDF plug-in for Firefox): your worm s/o; current version 9.3.3 (updated security important release 29/06/2010; See: http://www.adobe.com/support/security/bulletins/apsb10-15.html)
  ~ ~ Red: check your version here ~ ~: http://www.mozilla.com/en-US/plugincheck/
  See: http://support.mozilla.com/en-US/kb/Using+the+Adobe+Reader+plugin+with+Firefox#Installing_and_updating_Adobe_Reader
  ~ ~ Blue:you may be able to update to Adobe Reader installed on your system~ ~ instead of going on the Adobe site and download. Open the Adobe Reader software installed on your system (in Windows, start > Program Files, find and click on Adobe Reader to open the), click Help, click Find updates. Allow the download / update to occur. If you use this method, no need to proceed with the instructions below, but look at the two downstairs bulleted items ""NOTE for IE:"and" see also: "." Restart Firefox and check your new version here: http://www.mozilla.com/en-US/plugincheck/
  ~ ~ Blue:If you go to the Adobe site to download the Adobe Reader course:~ ~
  -use Firefox to download and SAVE to your hard drive (save to the desktop for easy access)
  ~ ~ Red:-see the images at the bottom left of this post to see the steps on the Adobe site ~ ~
  -the release of Firefox (file > exit)
  -In Windows: make sure that Firefox is completely closed (Ctrl + Alt + Delete, choose Task Manager, click the processes tab, if "firefox.exe" is on the list, made a "firefox.exe" right-click and choose end process, close the Task Manager window)
  -In Windows: double-click the installer for Adobe Reader you just download to install/update Adobe Reader

  • NOTE: under Vista and Windows 7 you may need to run the installer of plugin as an administrator by starting the installation program via the context menu if you do not get a UAC ask permission to continue (that is, nothing seems to happen). See this: http://vistasupport.mvps.org/run_as_administrator.htm
  • NOTE for IE: Firefox and most other browsers use a Plugin. IE uses a version of ActiveX. To install/update the IE ActiveX version, the same instructions as above, except use IE to download the ActiveX Installer. See: ActiveX
  • See also: http://kb.mozillazine.org/Adobe_Reader ~ ~ Red:AND~ ~ How to change options to add Adobe to the list of allowed sites

• WINDOWS CANNOT FIND ANY ADDITIONAL NETWORK (DIAL-UP AND VPN) OTHER THAN THE WIRELESS NETWORK

  ehmm I just installed nokia 6600 pc suite on my computer so I can access the internet on my computer through the usb cable. Installation and drivers have been installed correctly. I can access the internet on the handset but when trying to connect to the internet via USB with the computer "I get a message that windows cannot find any additional network." Its really disturbing that I can do to fix this. Can someone help me please.

  Even if a USB device, it does not create a new network connection for you.  I fear also that you use a regular USB cable - those connections often require a crossover cable (but more on that later and I guess it should work it is how it is advertised).  Go to start / Control Panel / Network and sharing center / set up a connection or network / and choose the first option (you can also check the main page to see if the connection is listed but I doubt it).  Choose to set up a new connection and follow the instructions - ensuring that you enter the correct settings when it is required.  You should perhaps install device drivers, firmware and or software for the device to work properly - read the installation mode (and call technical assistance from Nokia to help you put in place - they know more about what we do and should be happy to guide you through the process and even to set the settings on your computer until you log - that's what I would do in your before circumstane even of) ask for help here).

  To start / Control Panel / Device Manager and check all the new drivers (double clck on them) to confirm that they say that they do not work properly.  Go to start / Control Panel / Add Haedware and have the system check new hardware devices - if it finds, install them (it is perhaps what is missing in this process).

  I hope this helps.  If nothiing suggested I bring, don't hesitate not to contact Nokia for assistance - I'm sure they'll have you place and operate at any time.  Keep me in the loop.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• One application other than the Hyperic Agent can enter data in the DB?

  Hello Experts!
  
  I'm a newbie regarding Hyperic, and my customer is asking me questions such as:
  
  "Can we control a Perl process to measure with Hyperic Agent?" - I think the answer is 'no '. Is this correct?
  
  "Otherwise, if scratch us FlatFile newspapers (e.g., using a Perl process) to gather metric data about a process, can we simply insert the resulting data in the HQ table in the DB (without Agent Hyperic and Plugins) and so 'wrong' HQ allowing us to take advantage of its visualization abilities? -I think the answer is "no--at least not safely. A likely reason among others for the failure of such an approach could be unique complexity ID/key. "Is this response on the target?
  
  Although I would be happy to any detail in your answers, there is no need to go into deep detail - I'm just trying to get an overall assessment.
  
  Thank you in advance and best regards.

  Hello

  You can monitor the health of a process either a script or a compiled program. If you are wanting more detailed metrics using a custom plugin brings together the like this.

  Agents collect metrics and events and pass them on to the server, which then inserts into the database. Without going through this channel is dangerous because you speculated and will lead to very bad results. Agents can collect the log as an event entries. There are a few default plugins that can do this and you can also write your own plugin (much easier than it sounds) to collected the lines in the journal.

  So the simple answers are 'Yes you can monitor a process and logs' and 'no. do not bypass the server.

• The pencil of Apple requires a port light to recharge.  Does anyone know a USB male to female adapter port lighteners that would load the pencil on one device other than the iPad?

  The pencil of Apple requires a port light to recharge.  Does anyone know a USB male to female adapter port lighteners that would load the pencil on one device other than the iPad?

  Apple pencil comes with its own map of woman to woman, so you can use a standard lightning cable USb and charger to charge

  Not sure there is no 3rd party yet.

• Hi, I just bought a macbook pro 13 ", however it has no ethernet port, have I need to buy a device of air port and what one do need me?

  I just bought a macbook pro 13 ", however it has no ethernet port, have I need to buy a device of air port and what one do need me?

  Your MacBook Pro has built in WiFi.

  Wi - Fi

  802.11ac wireless Wi - Fi network; IEEE 802.11a/b/g/n compatible

  It is the best way to connect. You will need a router if you don't already have one.

  If you want to use ethernet wire you can use this cable. ter http://www.apple.com/shop/product/MD463LL/A/thunderbolt-to-gigabit-ethernet-adap? fnode = 8 b See the following link for more useful information if you are new to Mac.

  Kim

• my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  Hello

  You should check with the help of the manufacturer modem and if it is provided by your ISP support.

  Not really a Windows problem.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Firefox is redirect to sites other than the one clicked on.

  When you click on search sites by using the bar (address bar not) search, you are redirected to one site other than the one you clicked on. It happens not on all sites found, but on a large number of them. However, in all cases where sometimes the site redirected to is [adlinksearch.com]. I use PC Tools Spyware Doctor and it has found no problems with Malware. I can go on the site if I put the address in the address bar. I use igoogle search bar. Please help with this issue, because it is very annoying.

  This has happened

  Each time Firefox opened

  == Unknown as to exactly when he started

  Firefox closes alltogether when you go to youtube videos, not youtube itself. Redirects to other sites. ran malaware and spybot. Any suggestions?

• He also just on my screen that someone other than the same IP address as me, what should I do to change?

  was informed someone else that my IP address whay I can do

  It also comes on my screen that someone other than the same IP address as me, what should I do to change

  Hi marionnaismith,

  I suggest watching this thread, because it is similar to what you feel:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/Windows-has-detected-an-IP-address-conflict/e43f2512-10cc-49E8-9500-831f9892f8dd
  Also, here is an article from Microsoft that provides much more detail on this issue, if necessary:
  http://support.Microsoft.com/kb/120599

• How can I set the format of Windows Media Center at 16:10 in other than the full screen?

  How can I set the format of Windows Media Center in Vista at 16:10 in other than the full screen? I use a screen as secondary display 1680x1050px.

  Hello, YPOC

  It is not possible to change the proportions for Media Center in windowed mode.

  The aspect ratio has been changed in Windows 7 and uses a format screen mode to windowed.

• Cannot access SQL more from other than the Oracle users

  Hello

  I installed Oracle 11 g R2 on Red Hat 6. My problem is that I can't access sqlplus from other than the oracle users.

  I put the PATH, the ORACLE_HOME and ORACLE_SID to the correct values.

  Session1

  Connect as: oracle

  [email protected] password:

  Last login: Sun Aug 24 01:24:46 192.168.202.1 2014

  [oracle@localhost ~] $ echo $PATH

  /usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin:/Home/Oracle/bin:/Home/Oracle/app/Oracle/product/11.2.0/dbhome_1/bin

  [oracle@localhost ~] $ echo $ORACLE_HOME

  /Home/Oracle/app/Oracle/product/11.2.0/dbhome_1

  [oracle@localhost ~] $ echo $ORACLE_SID

  ORCL

  [oracle@localhost ~] $ sqlplus

  SQL * more: Production release 11.2.0.1.0 Sun Aug 24 03:17:32 2014

  Copyright (c) 1982, 2009, Oracle.  All rights reserved.

  Enter the user name:

  Session2

  Connect as: nada

  [email protected] password:

  Last login: Sun Aug 24 02:31:49 192.168.202.1 2014

  [prithwish@localhost ~] $ export PATH=$PATH:/home/oracle/app/oracle/product/11.2.0/dbhome_1/bin

  [prithwish@localhost ~] $ export ORACLE_HOME=/home/oracle/app/oracle/product/11.2.0/dbhome_1

  [prithwish@localhost ~] $ export ORACLE_SID = orcl

  [prithwish@localhost ~] $ echo $ORACLE_HOME

  /Home/Oracle/app/Oracle/product/11.2.0/dbhome_1

  [prithwish@localhost ~] $ echo $ORACLE_SID

  ORCL

  [prithwish@localhost ~] $ echo $PATH

  /usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin:/Home/Prithwish/bin:/Home/Oracle/app/Oracle/product/11.2.0/dbhome_1/bin

  [prithwish@localhost ~] $ sqlplus

  -bash: sqlplus: command not found

  I guess that I could not access sqlplus as the Nada the user has no access to X11R6

  [prithwish@localhost ~] $ cd...

  [Host prithwish@localhost] $ ls - ltr

  Total 8

  drwx-. 30 oracle oinstall 4096 23 August 23:51 oracle

  drwx-. Nada Nada 4096 24 August to 02:33 27 Mathieu

  [Host prithwish@localhost] $

  My question is, although quite stupid, that double

  (1) I have to change the permissions of the directory oracle of 755 for any other user to access the sqlplus?

  (2) why is the user directory under the folder created with permissions of 700, even when the umask is set to 002? Change the permissions of the directory under/Home oracle will cause security problems?

  My apologies for being naïve. It's the first time I installed Oracle under UNIX

  Kind regards

  Prithwsh

  Actually, the default procedure is NOT to install oracle to X11R6, but in/opt/oracle. or maybe/usr/local/oracle.

  This is what you're going to be recommended in the installation documentation, and in doing so, don't forget to run rootpre.sh and root.sh, I never had security problems and could run Oracle from any account.

  Sybrand Bakker

  Senior Oracle DBA

• Special characters other than the number and the hyphen

  Hi all
  
  I have a table that has a column named ID. This column contains the employee id, but during the loading of the files in the Tables, some records are contains various special characters. The sould IF contains number and hyphen (-) only. All other characters are special characters.
  
  I need to write a procedure/function, where I spend that id and check in the table if this ID contains special characters other than the number and the dash and remove it and then check the length of it (say 10).
  
  It should then resubmit this comment to refer to another ID such as "invalid ID".
  
  Can someone help me how to write the procedure/function with this feature?

  with t1 as(
  select '12345-2345 ' val from dual
  union
  select '34556- 5627'  from dual
  union
  select ' 56556-5236'  from dual
  union
  select '11111-1111' from dual
  ) select regexp_substr(val,'^[0-9]+-[0-9]+$') FROM t1
  where regexp_substr(val,'^[0-9]+-[0-9]+$') is not null
  

• What are some editing apps good free photo for Mac, other than the Photos of Apple?

  Hi everyone, I'm looking to see what free apps, you guys use for editing photos?  I have a photography class to come and play with options other than the use of pictures of the Apple app.  Nothing against the app, I just learn more.  Thank you.

  Strange question to the users of the forum pictures - of course, the answer is Photos for Mac

  Photos is optional and if you don't like it, then, Google is your friend

  LN

• my macbook pro 2015 lacks an ethernet port. How can I connect using ehternet?

  My macbook pro doesn't have an ethernet port. How can I connect my wifi is spotty, but the wire is good? Thank you!

  You will need an Ethernet to USB connection

  http://www.Apple.com/shop/product/MC704LL/A/Apple-USB-Ethernet-adapter