My his laptop makes a beep when I press the power button / stop and it does not start

Similar Questions

• PowerEdge T410 won't do anything when you press the power button / stop.

  My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

  -Who-

  I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

  Problem solved

• HP DV6 6115TX UP STARTS NOT WHEN I PRESS THE POWER BUTTON / STOP NOTING HAPPENS

  LAPTOP: HP DV6 6115TX

  1. WITH THE BATTERY AND CONNECTED AC-

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  2. WITH THE BATTERY ONLY

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  Hello @HPDV6-6115TX ,.

  Welcome to the HP Forums!

  I understand that you laptop is not turning on.

  If the laptop has no power, other than the AC adapter connection indication, there is little that can be done.

  The adapter ring is HQ shows a white LED would suggest the adapter supply fine and offer pay-per-view mother, or at least the internal power connector. This means it is a flaw in the motherboard of the laptop and most likely requires a repair.

  You will want to check that the RAM and HARD drive are in place and connected, as well as internal power cable. You can do it by following your product Maintenance & Service Guide.

  HARD drive: Page 62.

  RAM: Page 66.

  Power cable: Page 83.

  If it does not, you will need to contact the HP support by phone for service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.

  Hope this helps!

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• Tecra A4 does not light when you press the power button

  When I press the power on button it turns green for 4/5 seconds then turns off.
  "I do all the tests the support on the page:
  
  * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

  * Connect the adapter to the computer.

  * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

  * Plug the power adapter into a different plug.

  * The battery, ensure that there are enough energy to start the computer.

  * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

  * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

  * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

  * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
  In vain:]

  You know? THX

  Hello

  There must be a hardware malfunction.
  You have tested a lot and nothing has worked
  I think there is not much to do, you all tired and I guess the authorized service provider could help you

  If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

• my laptop stops automatically and randomly and start again after pressing the power button / stop

  Hello

  my laptop stops automatically and randomly and restarts after pressing power button.my pc running windows 8 version of system.can you please solve this problem.

  Hello

  Check if the quick start option is enabled, your laptop. Here are the steps:

  1. open the Power Options window. Use one of the following methods:

  A. press the WIN + R keys at the same time to launch the Run dialog box. After that, type powercfg.cpl , and then press enter.

  B. press the WIN + X keys at the same time to launch WIN + X Menu. After that, select Power Options.

  C. the Start screen and the Windows of type power will show the results, select the Power Options.

  2. click on settings , then choose change how the power buttons.

  3. scroll down and look for turn the (recommended) quick start under stop settings.

  4 uncheck the checkbox, and then click save changes.

  Note: if the option has said isn't here, scroll down and select change settings that are currently unavailable to change.

  5 restart your laptop.

  Let us know how it goes.

• I have an old laptop Armada M700! I've implemented a power on password and it does not work! Is there a way to reset the password? Even the laptop will not power

  laptop worked very well slow, but very well so I tried a bit of security, so I put the power on password good this morning when I try to activate the password does not work!

  Hello

  I suggest you to contact the manufacturer of the computer for help on this issue.

• My sansa e260 suddenly is energized when I press the power button. Help please

  Hey, today my 260 just stop feeding up out of nowhere. I don't have the latest version of the software package, and when I tried the update, he couldn't. It lights up when I connect the usb cable, but not when its disconnected. Before this he repeated bad tracks on all my songs even if their were not all and kept cutting. Can anyone help me please with this problem?

  It seems that the battery is detached. Open the back (4 small screws, don't lose them), take out the battery, put in comfortably recharges. If it does not reload it, he could be dead - they have no last forever - and you can get a new one on Amazon or eBay.

  For bad tracks, ChkDsk. Might as well do it first, since you can connect.

• When I press the power button on my computer, it will beep but never displays the image on the monitor.

  original title: my windows vista only make a bep but not star of the monitor

  When the tray to start my computer to only a bep bep

  Hello

  beeps normally indicate a hardware problem

  read below to find out what your

  http://www.computerhope.com/beep.htm

  http://www.pchell.com/hardware/beepcodes.shtml

  If you can't fix it contact the manufacturer if under warranty

  If it is under warranty, contact a local reputable computer repair workshop

• Satellite L20 - Orange LED flashes when I press the power button

  For 6 - 7 times and nothing happens after that, the battery is completely dead and the adapter works fine

  I measured the voltage on the map that powers the battery and found 3.33v on 2 of them, the third is 0 v and the last of them starts by 0 v and goes up to 10v and more

  Hello

  Strange, but it might be a hardware malfunction.
  But first, you should try to remove the battery and the AC adapter. Attendre wait up to an hour, then reconnect the two devices.

  If it doesn t work it could be a motherboard problem or something else. I recommend you contact a technician for laptop.

• Screen flashes on then off quickly when it is locked and you press the power button / stop?

  Using iPhone 5s, I bought this phone a week ago.

  Facing this problem since this morning.

  Try a forced reboot. This will affect all the data. To force the reboot your device, press and hold the two buttons of sleep/wake and home for at least ten seconds, until you see the Apple logo.

• HP-G62226TU: my laptop won't turn on when I push the power button

  Hello

  My laptop does not turn when I push the power button / stop and nor adjacent to the plug adapter lights turn on when I put the power supply. It behaves like completely dead. I pressed the button for 30 seconds as suggested in the following thread.

  http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/my-laptop-won-t-turn-on-when-I-...

  My laptop is 2.5 years old and was working fine without any problems so far.

  Please suggest.

  Thank you

  Himanshu2303 wrote:

  OK... I learned to get the motherboard changed. How much it will cost in India for my laptop?

  What do you suggest I should do?

  How much will it cost in India?  I have no idea. I live in Europe.

  I suggest to ask a repair shop of PC or laptop.

  If the cost of repair is more than 50% of the current value of the laptop, you would be better sourcing of a notebook replacement.

• 15 170tu ac: I HAV to press the power button several times to start the laptop...

  I HAV to press the power button several times to start the laptop... works well with the power supply on.

  all My drivers & bios is updated... but when I opened the lid... I HAV poer press several times the button and he then began 4-5 min.

  Hi @Vishalwagh123,

  Welcome to HP's Forums a great way to get help. It's a great place to find answers and advice! Thanks for the post.

  I understand you have questions turn on/off the device and you must press the power button several times for him to start. I'll be happy to help you.

  Please try these steps first. Perform a hard reset.

  • Steps to do:
  • Turn off the computer and unplug the charger. Then remove the battery.
  • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
  • Replace the battery and the charger plug it back. Try to turn on the computer.

  If it fires up immediately the issue is resolved. Otherwise, try to turn on the computer without the battery and check that it works immediately.

  In your message, you said that it works very well with the charger. However, I need more clarity here to help you better.

  It works immediately when the adapter is connected and the power button is pushed only once?

  If you again press the power button several times, it may be a faulty power button, and you will need to contact the hotline at the service of the unit.

  Let me know what happens when you try to turn on the unit without the charger?

  Visit this link to contact support phone:

  http://HP.care/2bjG4nE

  Hope the problem is solved without hassle. Please keep me in the loop.

  Take care and have a week Holy.