My instant HDTVPCI ADSI device does not work correctly.
As I said earlier, my instant ADSI HDTVPCI device is not operational, and Device Manager cannot start or reset for me. Please help me to fix this problem, thanks. William Schotts.
Follow these methods and check if that helps:
Try running the fixit from the link give below and check if this can help:
Hardware devices not detected or does not
If the drivers are not installed automatically install use the software that came with the hard disk and install the drivers and software. Refer to this article:
I just plugged a usb2.0 webcam on my laptop with windows vista. It is loaded ok, but the device manager says that the device does not work correctly. Any ideas please.
I just got a webcam via ebay and plugged into my laptop. I'm working on windows vista. He finds and load device software right away, no problem. But I can't work. go into my device manager it tells me that the device does not work correctly. Any ideas please.
The first thing I would try is to connect the webcam to another computer to make sure that the webcam is not defective.
Now, check out these links and return to the State of the question.
When hardware installed in or attached to a computer doesn't work properly, it is often because of a driver problem.
Here are a few common problems with drivers and the means to solve them.
See the following link for more information:
Also check out the following link and run the fixit available.
The fixit diagnose and solve problems with the equipment. (USB) Keyboard and mouse are not detected by the Manager of devices or when they do not work.
Hi, I have Windows Vista and I use a computer laptop Dell studio. When I insert a disc into my CD/DVD drive, the drive spins and it looks like it is about to start and makes the same noise start several times and then just stops. My computer does not record that there is a disc there. If I double click on the DVD drive in 'My computer' it ejects my disc and says "insert the disc in drive E".
I went on the 'repair' Microsoft online scanner and it told me that there is a problem, but he can fix it. In Device Manager, under CD/DVD-ROM readers I have Optiarc DVD +-RW AD - 7640S. Under device status - general - properties, it says "this device does not work correctly. He also says that I have the updated driver.
I even uninstalled the driver as a last resort and then restarted my computer. It reinstalled the driver for me, but there was no change. Please help me!
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.
Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.
Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr Fixit
The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
When you insert a CD or a DVD, Windows Vista may not recognize the disc
Your CD or DVD drive cannot read or write media - A Mr Fixit
CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
Setup after booting from the DVD (AHCI)
Drive CD - R or CD - RW Drive is not recognized as a recordable device
Hardware devices not detected or not working - A Mr Fixit
Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.
Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.
Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry
entries that do not fix the resolution of problems and those who "could" be the cause.
Check with your Maker system and a device for the two possible firmware updates and the
correct registry entries for your car.
Here are the keys in my opinion, are those in question - for the CD/DVD drive of course subkeys as
There will be other subkeys in these keys. Do not forget to ask involved specific keys as well as the
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.
Forums - a lot of expert real help
I hope this helps.
Rob - bicycle - Mark Twain said it is good.
I hope someone can help.
Just bought this laptop and for some reason, I get an error message come saying the Synaptics Pointing Device does not work properly. The touchpad loses some functions and a warning appears informing me of this. I can still use it, but disappears from the icon in the taskbar with the flashing blue dot - when I go into the control panel it says the driver and he asks if I installed another ps/2 pointing device driver
Looking forward to any help you can give.
Suggest that you reinstall simply touch pad drivers. Maybe new version?
So, just uninstall drivers, restart your computer, reinstall the drivers.
Drivers are located on the download page of European drivers.
Hello, can you help me find driver problems, sir.i am on hp pavilion g6 Series notebook.i found this message there, Windows reports that the "Microsoft Teredo Tunneling adapter" device is working properly. But I opened the Device Manager and I found the icon and I double click and then try to update the driver software but I found ago encountered a problem... This device does not work... Sir can you help me solve this problem... Thank you for your time
Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP Pavilion g6-2225tu issues of driver for laptop and have on the Teredo Tunneling pseudo-interface. Right click and delete all Teredo Tunneling pseudo-interface. Restart the computer. You could update driver software by right click, browse computer for driver software. Select let me pick from a list of device on my computer-> network adapter drivers > Microsoft > adapter Microsoft Teredo tunneling. You can enable system restore by following this document.
I'd be happy to help you if necessary because there are many models of HPNotebook, I need the model number. How can I find my model number or product number?
Please respond with an operating system that you are running:
Operating system Windows am I running?
Please let me know.
Original title: it does not recognize the external HARD drive. (Convert HDD mobile external HARD drive)
I have a Sata Drive en-plus close card I bought, I successfully installed the HARD drive and plugged (supposed to be taken & play), it does not recognize the HARD drive and I tried the computer management and replacement of INF. USB but still does not. Also, has problems. Drive HARD Toshiba satellite came 500 GB Fujitsu HDD.
The point of this is to clean up the cause of the car, there an OPS on it, but I have not anymore!
Need help please!
See the link and check if it helps:
Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
Check the link and try to run the Microsoft Fix it:
Hardware devices do not work or are not detected in Windows
My laptop is a HP G7030EA - MS Windows Vista Home Basic 32-bit SP2 Intel Pentium Dual CPU T2330 @ 1.60 GHz, 1.0 GB RAM, Mobile Intel 965 Express Chipset Family, bought new in February 2008. I have not changed any hardware, software, etc. I do not use it for games, only for things such as e-mails and visit websites
Until last month when my desktop computer broke, I used the laptop only occasionally as a backup of the computer. It never quite worked and seems to be unable to handle several tasks at once, often taking minutes for Google to load. When I get impatient and click the mouse too much I heard a horrible noise and the screen mouse cursor freeze for a minute or two.
As the laptop has become my main computer at the moment, I downloaded AVG PC Tune Up to see if it would improve it performance has not helped. I was surprised to see how much memory the AVG2013 anti virus program uses, but wonder if the speed of connection and freezing problems I experience result (AVG Tune Up conclusions on) the Teredo Tunneling pseudo-interface unit does not properly.
I follow AVG on screen re boards: looking for a software driver update but none was found, and I got the message "the best driver for your device software is already installed. Windows has determined that the driver software for your device is up-to-date, Tun Miniport, Microsoft Map.
This left me confused. If there is a problem with this device, no solution seems to exist.
Any help that will allow my laptop to function normally is welcome.
I understand that you want to know if the teredo adapter can cause performance problems.
The teredo adapter should not cause performance problems. It is really just used to allow devices work IPv4 with IPv6 Internet service provider. If the ISP was using IPv6 and your system did not have the adapter teredo, so it wouldn't work properly with the service provider. For now, IPv6 is a significant minority that the world continues to work on IPv4 as not all networks, Internet service providers, and businesses are not entirely passed to IPv6.
This thread on the Microsoft forums goes into a little more detail about the adapter teredo including how to disable it so that you only see it in Device Manager. Unless you are using IPv6, this shouldn't really be a problem.
If you start in safe mode, the performance problem persists? Turn on the computer and press F8 once per second for the Mode option, safe mode with networking. This will help you to further isolate the performance problem.
Furthermore, does this happen that the adapter is connected or not?
I have this unit in my ASUS laptop: HL-DT-ST DVDRAM GT32N SCSI CdRom Device,.
and it is not read most of the inserted discs. Prints are better, but is not able to read one of my CDs or DVDs written at home.
A few years ago I tried to solve the problem and that I can remember other users had the same problem and the driver update has been recommended, but I also discovered that the support for this product is complete, and I couldn't find all the archives. I dropped.
Now I'm able to download a driver is already installed on the computer that has the version number: 6.1.7600.16385.
I suppose that there could be problems other than the driver himself.
Try to clean the disc with a cleaning disc.
If cleaning doesn't help not the drive has a hardware problem, since it corresponds sporadically.
For discs do you you try to use the format of the ISO image.
Should which CD or DVD format I use?
Forums - a lot of expert real help
Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.
DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
I installed Windows XP Home edition on my Satellite L300-19f after change SATA compatibility I installed Windows XP Home edition and installed all the drivers and everything's fine, but the audio device does not work. I downloaded the driver from DOWNLOAD & support center, but he can not detect.
BTW: he used to work on Vista.
What should I do?
And thank you
-Download driver audio Realtek HD Realtek page.
-Go to the Device Manager
-Remove the sound card.
-Remove the High definition Audio Controller
-Restart the laptop.
-Reinstall the Realtek HD audio driver
I bought a model U400-17R with Vista Home. I formatted and installed Windows XP Professional download drivers XP Toshiba site.
Everything works, but my Sound Device does not work. When I check in the Manager of devices the Sound Drivers are there and it says working properly.
I'm lost... Can someone please help?
I think you have the same problem like me a few months ago.
I installed Win XP SP2
The t is not his work because I didn't install the patches MS; KB835221 & KB888111
The patches must be installed as a first step, before the audio driver is installed.
If you have already installed the audio driver, then you must remove (uninstall) before install you the patches Ms.
PS: The MS patches are part of the SP3
My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »
Is anyone know how can I access my hard drive again?
You has made changes to the system before the error appearing? Cancel the changes.
(1) in Device Manager > right click on the driver, and then select uninstall
Reboot and Windows will reload the driver
(2) remove the upper & lower filters that cause errors in Code 31
Access the manufacturer's Web site and search for updated driver
Direct3D devices does not work on Windows XPHello1. what exactly happens when you try to access Direct3d devices?2. you get any error message?3. If it works well before?4. don't you make changes to the computer until the problem occurred?I suggest you to follow the steps below and check if it helps:
Method 1: Try to uninstall and reinstall the Direct X on Windows XP:
a. open the registry editor by running Regedit from start > run.
b. then, navigate to the following registry key.HKEY_LOCAL_MACHINE\Software\Microsoft\DirectXc. here, delete the DirectX folder, exit the registry editor and restart your computer XP.
d. when starting the system, after the reboot, your system will be reinstall DirectX 8.1 which is originally preinstalled Windows XP operating system.
Once it is done the upgrade to x 9 live.
Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756Method 2: If the problem persists, then try to install the latest graphics driver from the link below.Hope this information is useful.
Original title: Hybernation question
After hybernation, all usb and wifi mobile devices does not work. Similarly, it is not stop as well. I turn off the power to the network option all usb hubs. Problem however still closes. Please suggest. I have Windows XP Sp3 installed. All the drivers and the windows update is up to date.
1. what happens when you connect any USB device to the computer, or trying to shut down the computer after hibernation?
2. do you have security software installed on the computer?
3. did you of recent changes on the computer?
4 when was the last time it was working fine?
See the below Microsoft article and try the steps mentioned, check if it helps.
Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation
I suggest that you download and install the updated driver for the network adapters and display on the computer by visiting the card manufacturer or computer manufacturer website manually.
How to manage devices in Windows XP
Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel
This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.
Follow these methods.
Method 1: Follow these steps:
(a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.
(b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.
(c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:
Remove or reconfigure newly installed unit.
Restore a version prior to updating the driver.
Use system restore to undo the Device Manager recent related changes.
(d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.
Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry
Method 2: Update the latest graphic drivers.
Updated a hardware driver that is not working properly
My cd rom device does not work because its configuration in the registry is damaged, (error Code 19). Tried all the easy solutions (update - was active), any ideas? Thank you
· What is the accurate and complete error message?
· You will remember to do recent changes on the computer before this problem?
I suggest you follow the steps mentioned below:
Race fix from the following link and check if the problem persists:
If the previous step fails, follow the steps in the link:
If the previous step fails, follow the steps in the link:
Maybe you are looking for
Hello Recently, I dropped my phone and cracked my screen, the touch screen no longer works, but the fingerprint was not working. I managed to take it to the local store (no apple store or authorized dealer). They agreed the phone and asked me if I ca
I can't use my iphone properly I can't download form app AppStore
Hello, a few days before had been developed new drivers for GMA X 3100.I downloaded on the Intel site, but I can't install it. I found a driver for this card graph on the Toshiba site, but the drivers were too old (September 2008). Why not the Toshib
Hi, my problem is my restore points went on my pc, the error message says I have to contact the administrator of my domain, I am the administrator, but I have never heard of the area?, how get to this point and restart my restore .__thanx function.
How do the domain administrator.
For a week now, I have been do to the tabs to load each time when I started FF they add which of them just recently been updated. (One) thank you for the installation of Forecastfox (fixed version) second) thank you for the installation of S3. Google