My internet connection is lost at home after a few minutes. I re - turn on the wifi disabled, ten and it works again for a few minutes and then repeats. It works fine everywhere else?

Similar Questions

• The internet connection is lost when the computer puts itself to sleep after that idlen too long time needs to restart to re-establish the connection.

  I lose the internet connection

  Window vista Home premium intel core 2 quad CPU q6600 @ 2.40 ghz, 3.00 GB ram the System 32-bit

  The internet connection is lost when the computer puts itself to sleep after that idlen too long time needs to restart to re-establish the connection

  Hello

  Control Panel - device - network - manager double-click the used network - power management device
  Tab - uncheck the computer to allow him to turn off the device.

  Control Panel - Power Options - check at each change of diet Plan - change Plan settings - advanced
  Power settings - check the settings there.

  You may reset the default power Plans and and then change them as needed.

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• my internet connection is lost during the use of the internet

  often, I find that my internet connection is lost while using the internet.how can solve the problem.

  Hello

  1. for how long are you facing this problem?

  2. don't you make changes before this problem?

  3. what operating system do you use?

  I suggest you to try with the mode safe mode with network and check.

  Start your computer in safe mode with networking

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

• 5210 kodak printer, when I print the document runs through the printer, but nothing prints, suggestions. worked fine until today after a move

  everything looks ok, but when I print the paper passes through the printer but nothing prints, suggestions. worked fine until today after a move

  Check with Kodak support or website to see if there's a test or a diagnostic process that you can run to identify the problem with the printer.  It is not likely to be a problem of Windows at this point.

• Error when opening file reader pen "the driver or network connection that the shortcut 'Target.lnk' refers to is unavailable. Make sure the disk is properly inserted or the network is available, and then try again. »

  Original title: during opening of pen drive file to msg "the drive or network that all connection 'refers to mpr shortcut' folders.lnk all in unavailable.make that the disk is properly inserted or the network is available and then try again."

  OS:-xp sp2

  pen drive :-transcend

  earlier, my USB had worms, bt Finally I took it off my ESET internet security (fully updated).

  BT still records are transformed into shortcut of 1 kb. and makes me worried coz I m nt able to open these files... Please help me out of this problem... I need my data, its urgent.help me as soon as possible to change these documents in their original format.

  my folders have files .doc, some do' report.unfortunately not have a backup of these files.

  target location: Z3ojKiH9lvFefkO0mG6Hl1XplgLV3L0YJVfdZRr3dtLhEN80DnzEPQX8Y2sziakx2axTnS4SA0447SPkbMn4QN

  In the location target properties are even 4 all records

  Clinical target:-H:\Z3ojKiH9lvFefkO0mG6Hl1XplgLV3L0YJVfdZRr3dtLhEN80DnzEPQX8Y2sziakx2axTnS4SA0447SPkbMn4QN\73mrVQz9rDByh9hfKJ9v0lt5z3m0s5hP0l.exe real sheet.xls

  What exactly is...

  I ve deleted the worms... checked by ESET, CLAMWIN PORTABLE, lapi ny window 7 WINDOW DEFENDER friend.

  ESET that worms have been Win32/AutoRun.VB.UG.Worm.

  now, I ve you gave details d, should know the problem I ve.i believe.help me

  Thank you for your time, but I did nt get the solution everywhere so formatted, it

• After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices &amp; their very good WiFi signals. Please help me solve this terrible problem...

  After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices & their very good WiFi signals. Please help me solve this terrible problem...

  Here's a tip for the user on the problems of Wi - Fi. Suggest from the top and bottom. Maybe one of them will help you.

  (1) restart you device.

  (2) resetting the network settings: settings > general > reset > reset network settings. Join the network again.

  (3) reboot router/Modem: unplug power for 2 minutes and reconnect. Update the Firmware on the router (support Web site of the manufacturer for a new FW check). Also try different bands (2.4 GHz and 5 GHz) and different bandwidths (recommended for 2.4 to 20 MHz bandwidth). Channels 1, 6 or 11 are recommended for 2.4 band.

  (4) change of Google DNS: settings > Wi - Fi > click the network, delete all the numbers under DNS and enter 8.8.8.8 or otherwise 8.8.4.4

  (5) disable the prioritization of device on the router if this feature is available. Also turn off all apps to VPN and retest the Wi - Fi.

  (6) determine if other wireless network devices work well (other iOS devices, Mac, PC).

  (7) try the device on another network, i.e., neighbors, the public coffee house, etc.

  (8) backup and restore the device using iTunes. Try to restore as New first and test it. If ok try to restore the backup (the backup may be corrupted).

  https://support.Apple.com/en-us/HT201252

  (9) go to the Apple store for the evaluation of the material. The Wi - Fi chip or the antenna could be faulty.

  Council: https://discussions.apple.com/docs/DOC-9892

• T430 cannot connect to WiFi unless the battery is removed and then re-installed

  Had trouble with t430 a colleague. It is impossible to connect to the WiFi unless the battery is removed and then reinserted. Once connected WiFi is strong and reliable. This seems to have started a few weeks without any notice. I think of a power setting? I also tried to replace the battery and the same problem. The two batteries hold high loads and are in a State of 'good '. Any suggestions?

  Solution has been update power settings to the driver does not allow the computer to turn off device to save power.

• I can't create an installer, after install the Vision Builder demo and then uninstall it. I can't create a Labview Installer more, he asks me an installer of generator of Vision, even if Labview my program does not have nothing to do with it...

  I can't create an installer on LabView, after install the Vision Builder demo and then uninstall it. I can't create a Labview Installer more, he asks me an installer of generator of Vision, even if Labview my program does not have nothing to do with it...

  Hi, Shada, this can happen if you include additional installers to your installer for example DAQmx. When you do this the installation program must include other files like MAX (Measuremente and Automation Explorer). Probably when you installed Vision Builder he updated MAX, so when your Installer try to understand MAX, his request the source where it was installed in your computer in this case Vision Builder.

  Here you can cache information so it is not asked once again, or you can download a version more recent fo DAQmx, then it will update MAX and change the dependecy.

  You can find more details about it in this KB:

  3S88PJMY knowledge base: why do I get an error message 'Missing Distribution' when you try to build an install...

  And to keep a copy, here's more information:

  How to stop missing delivery Notification whenever I build an installer?

  Best regards

• I have just re installed Windows XP. Windows installed after three attempts. When I turn on the computer there are three choices of Windows XP. Only the first works how to remove the other two?

  I have just re installed Windows XP. Windows installed after three attempts. When I turn on the computer there are three choices of Windows XP. Only the first works how to remove the other two?

  I have a hard drive. At least two partitions. C: 74.7 GB with 63.3 freespace
  D: 74.2 GB with 70.6 freespace
  These are my original specifications of the hard drive: 160 GB (7200 RPM) SERIAL ATA HARD DRIVE WI
  So I suspect there are at least one or more partitions hidden leaving 11.1 GB for hidden partitions!
  Windows is present on both drives C: & D:. In the directory windows on C:, the oldest entry is 19.12.12, 21.43 last 21.12.12, 22.50
  The first entry in the directory windows on D: is 19.12.12, 18.42 the last 21.12.12, 22.40
  I hope that makes sense to someone, any help gratefully received!

  As long as you have verified you dΘmarrez done on the c: / partition, Yes, you can reformat the drive D: / partition using Windows 'disk management '.

  J W Stuart: http://www.pagestart.com

• I'm unable to download the updates for Adobe reader 10.1.1. Win 7 claims that I am connected as a guest when I am the administrator. disabled UAC and added another user still cannot update.

  I'm unable to download the updates for Adobe reader 10.1.1 victory win 7 claims I am connected as a guest when I am the administrator. disabled UAC and added another user still cannot update.

  Original title: win 7 claims I am logged in as a guest when I am the administrator. disabled UAC and added another user still cannot update.

  Here's how you can find your status:

  1. click on the globe to start, and then type the three letters cmd in the search box and press ENTER.

  2. Enter the following command and press ENTER:

  NET user "user %%nom.
  What do you see under "a Local group memberships?

• I use LR 6.5 on an iMAC. Files RAF Fuji originally, I imported from an SD card worked and exported in the form of PSD and then after saving the files on an external hard drive RAF erased from Lightroom. I now want to import some RAF b HD files

  I use LR 6.5 on an iMAC. Files RAF Fuji originally, I imported from an SD card worked and exported in the form of PSD and then after saving the files on an external hard drive RAF erased from Lightroom. I now have to import some RAF of the HD files but LR shows them as dazed out and said that they have already been imported when I hover over the thumbnail. I have this problem when importing files in the same HD Canon CR2, and who have been treated exactly the same. Anyone got a clue as to why this is happening? Thanks, Phil

  Hi Phil,

  If Lightroom then reads these as duplicate files, it shows that they are already present in your Lightroom Catalog.

  You can search by file name and check if the image is present in your library.

  Kind regards

  Claes

• Try to download a trial of Lightroom, after running the installer of creative cloud, the download gets partially and then disappears.

  Try to download a trial of Lightroom, after running the installer of creative cloud, the download gets partially and then disappears. No explanation.  I already have CS6 installed on my macbook pro running 10.10.3 Yosemite.  I just want to try Lightroom trial.

  You can also download the Lightroom trial down links applications:

  Lightroom 6:

  http://prodesigntools.com/Adobe-Lightroom-6-CC-direct-download-links.html

  Lightroom 5.7.1:

  Adobe - Lightroom: For Macintosh: Adobe Photoshop Lightroom 5.7.1: thank you

• I apologize in advance if this isn't the right forum, but I need to do a reformat on this computer.  My question is, after you turn off the CC, PS, LR and bridge I have to uninstall as well?

  I apologize in advance if this isn't the right forum, but I need to do a reformat on this computer.  My question is, after you turn off the CC, PS, LR and bridge I have to uninstall as well?

  If you want to reformat the hard disk, in erasing all data on the computer, there is no need to uninstall.  Deactivation is sufficient.

• Internet connection is lost after 2 minutes

  In our House there are 4 teenagers - all with laptops, iphones, BlackBerry, etc.

  We have an internet connection to BT home hub.

  Everyone can connect OK except 1 latop - if using WiFi, laptop connect only for 2 minutes and he then loses the connection to the internet.

  The only way to get a WiFi connection again is to reboot the router.

  The laptop works fine when connected with an RJ45 LAN cable - problem only occurs if you use the WiFi.

  The laptop has Windows XP and Internet Explorer 8.

  The icon on the watch of the taskbar that the connection to the router is OK, and varies from excellent to mediocre according to how far the laptop is located rom the router.

  Why do I have a problem with this machine - I guess that it must be related to XP as all other machines have Vista or 7.

  Hello Gavin Duffy

  It may be possible but not likely.
  1. the system that only stays connected for 2 minutes, this problem only occurred after the settings have been changed in the router?
  2. did you check with your son that only security settings have been changed in the router?
  3. have you checked to see if this system is undergoing the same questions on other networks such as Café, the bookstore free networks or network of neighbors (the permission that they allow to connect)?
  Try to remove the wireless network profile and recreate.
  If you use 'Wireless Zero Configuration' to manage your wireless network, go to the network connections folder ("" Start > run ", type ncpa.cpl and click OK"), make a right click on the wireless network connection, select Properties, and then click the wireless networks tab, where you can highlight and then 'remove' an existing profile.
  After that you have removed, reconnect to your network and test to see if the problem still occurs.
  Thank you.

• The Internet connection is lost after installing Windows update

  Original title: put automatic has caused the loss of access to the internet

  After that the last automatic updates have been installed on the 8/17 or 18, I lost the internet connection.

  I had to restore my computer to an earlier date. When it was complete, I had access to the internet.

  I have reset my updates for having me choose when and which ones who.  When I install the updates, how can I know who we are at the origin of the problem.  In addition, how will I be able to solve the problem?

  Hello

  What is the error when you try to access the internet after upgrades?

  Method 1: Update the network drivers

  I suggest to update the network drivers, then try to update and check if the problem persists.

  Updated a hardware driver that is not working properly

  http://windows.microsoft.com/en-US/windows7/Update-a-driver-for-hardware-that-isn ' t-work correctly.

  Method 2:

  We can find the update by installing the updates one at a time, the origin of the problem.

  To do:

  1. click on Start, type windows update and press enter

  2. click on check for updates in the left pane of the window

  3. when updates are found, open the list and select one at a time and install them.