my iphone won't go into standby mode

Similar Questions

• T1530: DJ T1530 won't go into standby mode

  Hello

  We just bought a printer, DesignJet T1530 but we are facing a problem: printer will not go into sleep mode... and is very noisy (blowing fans)

  We put it up to 5 min, tried other times without success.

  Does anyone has a tweak?

  Thank you for your help.

  firmware: MRY_04_02_00.5 (will try the last of them but no indication on this issue in the release notes)

  SOLVED

  First of all, I tried to disable the internet functions without success.

  Have updated the firmware from MRY_04_04_00.4 and I appreciate very much the printer now in mode 'sleep'.

• Windows won't go into standby mode.

  I recently installed a new router (Linksys E3000) to link to a new laptop from my old office.  Now when I try to go into sleep mode, I get a message that says that the COM1 port prevents the day before the race.  He suggested a driver incompatibility.  The folks at Linksys say that it is a Windows problem.  Is it?  I have the Ethernet cable from my router connected to my desktop via COM1.  Thanks for your help.  BTW, everything works fine.

  Hello

  Try the solution listed: http://support.microsoft.com/kb/810905

• Printer won't go into Standby Mode

  I just bought printer e-all-in-one HP Photosmart 7510 - C311a, and constantly when my Mac that works on OS X starts in mode 'sleep' the printer sounds as if it is being initialized.  It also has a message on the screen to turn off the unit to avoid damage.  I do not understand, this printer is a 'sleep mode' too?  I don't want you must manually activate it offshore, but he makes too much noise until the mac is turned back on.  What should I do?

  Is the printer plugged into a power strip or surge protector?  If so, plug it straight into the wall.

• WSD Print device device driver prevents computer from going into standby mode

  WSD Print device device driver prevents computer from going into standby mode

  This message indicates that the computer was unable to fall asleep by a device driver.

  Look for the drivers updated printer manufacturers website or run the Microsoft Fixit:

  http://support.Microsoft.com/GP/printing_problems

• My printer interrupts communication with my PC when the P.C. goes into Standby Mode. Why?

  Until yesterday, the printer worked fine.  There is no cable or hardware change any.  I am running Windows XP with a jet of Lexmark color printer.

  When I restart the printer works fine.  However when the order goes into standby or hibernation mode, I can print is no longer when the box comes back active.  I get a message that "there is a communication error with the printer.  To correct this problem, a box appears I should go to start/settings/printer and make sure the "Enable bidirectional support" box is checked.  Unfortunately, I can't access the settings of the printer directly from the start menu.

  However, if I click on 'Options' that is displayed when the printer stops and I click "Troubleshooting", I don't see that the "enable bidirectional printer media" is more verified.  If I check, I get a message saying "printer is busy".  If I click on start again I get the same message and the "enable" box is unchecked.  If I hit Cancel, the box is also disabled.  I enter a loop that does not end.

  Any ideas how I can access the printer directly from the start menu settings?  Or how to prevent the impression of no longer communicate with my PC when it goes into sleep mode?

  Thank you much, long in advance for any suggestions you may have.

  It is a Lexmark Z-52.  After 8 hours of trying many different, including the link ideas that you suggested, I have determined that as a result of some recent Microsoft Download, the printer would work only if I used the Dell printing device incorporated in the installation software.  If I tried to install the Lexmark printer from the installation disc, I got the persistent problem.  I deleted all but access to the printer through the installed also origin and everything of fine.

  When I need to change the cartridges and align the jets, I install the Lexmark program, align the print cartridges and then remove the program Lexmark, using the default value of Dell for the printer remaining.

  It works, but why I had a problem, I don't know.

  TNX for the comments!

  Big Phil1

• Windows XP go into standby mode

  When I click on the icon the computer shutdown ensures he begins to go into sleep mode and then turns back on. I can hibernate the computer or stop it but not in standby

  Can go into the Hibernate mode, but not the sleep mode so use Hibernate

• Satellite 1800-314: when I close the lid it won't go in standby mode

  I hope someone can help.
  I recently had my Satellite 1800-314 (Windows XP) re-formatted and now when I close the lid he's going to sleep... the power light flashes orange, when I opened the lid still once, Windows stops and then restarts. I tried to install the Toshiba power settings, defining "when I close the lid, in standby mode", does not.

  Have uninstalled then Toshiba power settings and all the settings of ordinary power in the Panel of 'sleep', etc., but it REST did not return to standby mode.
  I'm tired now.
  Is there a simple solution that I'm missing?

  Grateful in advance for any help!

  Hello

  You know it's very important to install drivers in the correct order.
  The installation of common modules at the beginning is important because some drivers of Tosh need this application to work properly.
  If the energy saver has been installed on the operating system windows power settings will not work.
  Toshiba crash parameters the parameters of Microsoft.

  In addition, please check your BIOS preinstalled. Compare the version with the BIOS on the page. If your uses of the unit the old version, so try to update.
  But be careful. You must use the good BIOS and the right procedure upgrades.

• ESX Server won't go into maintenance mode - Timeout

  We have 1 host ESX 4.1 support our view desktop computers. I tried to plan a reorganization of the host during the night, but jobs would not be the exit ramp leading to the maintenance task timeout mode.

  What will do to make desktop computers will be exit during this upgrade? I put all the desktops into maintenance mode before the host trys to remedy?

  Thank you

  Travis

  This part of a cluster DRS ESX Server? If not you will need to manually stop or vmotion the VMS to another ESX host before it can go into maintenance mode - if it's part of a DRS DRS cluster must be set fully automated so DRS can automatically vmotion the VMs before entering maintenance mode.

• cannot go into standby mode automatically only manual

  How can I get my computer to go to stanfby automatically

  Hello
  From > start / Control Panel > settings > Control Panel, open Power Options then power management. Select the desired settings for standby and hibernation. OK your way out.

  Hope this helps,
  Don

• Portege 7140CT Shutting Down in Standby Mode - cannot close normally

  Hello. I bought a laptop Portege of CT 7140 for my son. It is a very good unit but has a "Shutdown" problem - only it used to closing, that is. It seems to power off, but the 2nd of the LHS on the front of the device flashes slowly. The user's guide explains what happens when the device goes into "Standby" mode I tried all the options of FN + F3 (off, standby and Hibernate) with no difference. I disabled the feature key installation in the Panel. I disabled the "Hibernate" mode in the control panel. All to nothing does not. Someone at - it an idea why this is happening and how can I solve? Thanks a lot for your help. Mike

  Hello

  I never heard of this problem, but maybe to reinstall the system can solve it.
  Or perhaps reinstall or update the BIOS will help you.
  I'm sorry that I don't have a better idea.

  Good bye

• Cannot restart; Function F8 does not work; stuck at "restart windows." Put in standby mode.

  Put the PC into standby mode.  Stuck in the status of "Recovery of Windows".  Impossible to restart.  Power off several times.  F8 doesn't work no more.

  I don't think that XP shows a message "Windows Recovery" when it comes out of Stand By.

  It does when it's Hibernation.

  If you've been cycling power, you can have damaged your system files a bit and should probably start by running a chkdsk/r from the XP Recovery Console.

• my iphone was droppped and custom lights, but you can which is a light on it as if it is in standby mode. is there any fixes for this.

  my iphone was droppped and custom lights, but you can which is a light on it as if it is in standby mode. is there any fixes for this.

  Try to do a reset. Hold home and buttons power together for 30 seconds or until you see the Apple logo.

  If that does nothing, there's a chance that the LCD connector has partially disconnected. Although it is most likely your LCD is damaged.

  Apple may offer a replacement of the screen. You must check in your country, how much they charge.

  Alternatively, you can look for a reputable independent repairer who can replace the screen for you. This means waive all the Apple warranty services. But it's a bit less expensive for a C. 5 If you go this route, choose a repairer who offers a guarantee of 6 to 12 months. And don't go with the cheapest.

• How can I configure my computer to it won't go into power saving mode every 2 min

  How can I configure my computer to it won't go into power saving mode every 2 min

  How can I configure my computer to it won't go into power saving mode every 2 min

  Change the configurations screen saver and hibernation / sleep appropriate for your desires.

• What can I do if the TV turns on and goes into sleep mode? Standby blinks 9 times

  Model KDL-46xbr2 power button press that TV is available on any photo goes into sleep mode which flashes 9 times stops and continues to blink 9 times

  Where is the help people?