My laptop cannot start or repair itself, Windows has been installed at the factory, so I have no boot disk, is there a way to get a free boot disk?
I had problems with my laptop for a few weeks, I used Chkdsk to fix the problem she was having. Yesterday the comp froze while I was using firefox and when I reset windows not load and cannot repair themselves. My OS was installed at the factory, and I have the product key, but Windows no disk. Is there a way to fix my computer without buying another drive in windows?
Hello
Here are the different ways to reinstall vista
Contact the computer manufacturer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it
they do it for a nominal cost of $
also ask them if you have a recovery partition on your hard drive to get back to the way you bought
you would normally press F10 or F11 or Alt + F10, 0 at startup to start the recovery process according to the manufacturer
Ask them of the exact key sequence
or borrow a microsoft dvd vista
Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer
they contain all versions of vista
This is the product key that determines which version of vista is installed
http://www.theeldergeek.com/Vista/vista_clean_installation.html
Save all data, because it will be lost, do the above
How to replace Microsoft software or hardware, order service packs and replace product manuals
http://support.Microsoft.com/kb/326246
and if you need a startup repair disk;
the link below is how to download and get a vista disk startup repair, which you can start from the
http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/
Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below
http://www.bleepingcomputer.com/tutorials/tutorial148.html
to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start
It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu
Change boot order it do dvd drive 1st in the boot order
Tags: Windows
Similar Questions
-
My laptop is dead where Acrobat Pro XI has been installed so that I will reinstall on another computer. How can I make my active serial number again?
Hello
Please download Acrobat Pro XI from here: Download Adobe Acrobat products. Standard, Pro | DC, XI, X
After downloading install it and on request provide the serial number for the XI and the product will be active.
If in case it gives you an error with activation please Contact Customer Care.
Thank you
Abhishek
-
A few years back, I bought CS5. because of my house having to repair my Adobe CS5 has been lost in the move. Then I had to take care of my mother who died later of cancer. I have now found my product but the person said the customer service there is no newspaper of me purchase of the product. I can't use the product that I bought because I don't have the registration code. So could I please get a refund and I will return the edition teachers and students of CS5. Thank you.
@
-
Windows Vista Edition Home PremiumI am not able to install windows vista on my laptop. A few days before my work laptop stopped and I have it for repair.The repairman told me that the boot Image does not. I have recovery disks gave him. He informed me that these discs also does not work.It has installed pirated windows vista on my laptop. I was not informed on this subject. Kindly help my window even.Concerning
Hello
As they installed a "pirated" copy of Vista, you need to reinstall Vista yet.
And if your recovery disks do not work, you should contact the manufacturer of your computer to the recovery disks does not.
There are several methods to reinstall Vista.
There is no Windows Vista downloads available from Microsoft.
You can contact your computer manufacturer and ask them to send you a set of recovery disks.
They should do this for a small fee.
To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:
You need to change the Boot order to make the DVD/CD drive 1st in the boot order:
How to change the Boot order in BIOS:
http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm
"How to replace Microsoft software or hardware, order service packs and replace product manuals.
http://support.Microsoft.com/kb/326246
Read what you don't say if you have the recovery disks when you bought your laptop, or if you have made yourself the recovery Partition
And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.
The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)
Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.
Ask them to the proper key sequence.
And if you do not score a manufacturer of recovery on your hard drive, you should be able to make your own recovery from her disks to reinstall the operating system.
Go to programs > name of the manufacturer of your computer > then their system or recovery tools software topics for them, depending on how it is formulated.
If you can't find any reference to it, contact the manufacturer for advice on how to make these recovery disks.
Some manufacturers have more available Vista recovery disks.
If this happens, you may need to try this instead:
You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.
Other manufacturers recovery DVDs are should not be used for this purpose.
And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs
Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:
"How to do a clean install and configure with a full Version of Vista '
http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html
And phone Activation may be necessary when you use the above installation method.
"How to activate Vista normally and by Activation of the phone '
http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html
See you soon.
-
I'm confused. APPARENTLY I MISSTYPED MY E-MAIL ADDRESS. THE CORRECT EMAIL IS EIEIESQ NET CASERS. I just asked my question on seen in firefox error uninstalled from my laptop and now unable to connect to the internet from this computer. My question was and how I can return a disk of firefox or another way to download and insall firefox on my laptop. The problem now is that I don't know what screen I should look for your answer. Will you send
change email spam/search bots like nobody here does support by email.
Your computer still has Windows Internet Explorer to surf the net.
-
I was fortunately sync-ed a year betweem my computer laptop Mac iBook and desktop HP - a lot of bookmarks - I am a student. My office had a small problem and I got it clean and reset to the factory settings. I'm now creating upward. I installed Firefox and made Google my default search engine. Then I logged in sync - no problem (even email, password... I wrote it!) I clicked sync, but my favorites are not come to the top. I closed Firefox and re-opened, but still no bookmarks. I looked at the settings and everything is checked. I wouldn't change anything. What Miss me? Thank you.
Both devices use new synchronization and more importantly on Firefox 30.
If you you don't need the synchronization of the former, and even if you use the same address as used for synchronization of the old all should operate under the new synchronization.
I think that the new synchronization drops devices that have not synchronized within the past 21 days.
Former site of Firefox Sync: new Firefox Sync https://account.services.mozilla.com/ site: https://accounts.firefox.com
-
What version of Windows has been installed originally on HP pavilion
I'm working on a HP pavilion Notebook. I'm trying to install the OS on one drive hard new, after the death of the other. I have the sticker code key, complete with the key code and a few other numbers, one under a bar code on the side of the tile. The part that rubbed off is the name of the operating system that is the key code. I don't know if it's XP, Vista, home, Pro or this Service pack. Is it possible to say what OS the key code is for with only the key code and the other two numbers?
I'm working on a HP pavilion Notebook. I'm trying to install the OS on one drive hard new, after the death of the other. I have the sticker code key, complete with the key code and a few other numbers, one under a bar code on the side of the tile. The part that rubbed off is the name of the operating system that is the key code. I don't know if it's XP, Vista, home, Pro or this Service pack. Is it possible to say what OS the key code is for with only the key code and the other two numbers?
Hey Apoctano
go to the link below, hp put the cell phone number in the drivers section and see what operating systems are found in the list
http://welcome.HP.com/country/us/en/support.html
Contact hp and give them laptop model number and the serial number SN her and ask them what was the preinstalled on operating syatem
they will be able to tell you
http://welcome.HP.com/country/us/en/contact_us.html
Walter, the time zone traveller
-
Separated from this thread.
Hello
Windows Update is grayed out (disabled) by my administrator. It is because they do not want MS update 74000 world machines to be updated without testing what the effect of patches). However, add a personal printer to our laptops is not against the policy of the company. So now, I have a printer that is useless for the work, because there is no right way to download the drivers?
Hello
You can try to contact Canon directly to see if they can provide the driver directly-
http://www.Canon.co.uk/Support/consumer_products/telephone_numbers/#.
(check the right geographic region at the top of the page if necessary).
If this isn't the case, I suggest that you contact your system administrator for advice.
I'm sure you understand, we cannot provide methods to circumvent / denying policies defined by the administrators of the system on the Microsoft forums
-
How to restore Windows Media Player decoder that has been installed on the Windows XP system
How to restore the original decoder that was once present with my system?
Hello jones augusta,.
I don't know when decoded provided with Windows XP.
Are you talking about codecs and decoders?Watch link here for DVD decoder.
http://Windows.Microsoft.com/en-us/Windows/downloads/Windows-Media-Player/plug-insWindows XP Video Decoder Checkup Utility
http://www.Microsoft.com/download/en/details.aspx?ID=9817Windows Media Video 9 VCM
http://www.Microsoft.com/download/en/details.aspx?ID=6191I hope this helps.
-
I have more the Firefox button on the top line. He was replaced by a summary of the content of the page, that I'm currently looking. How can I get that back. I use Win7 and Firefox was last updated.
Thanks for your help, I solved it myself in menu under display, uncheck options.
-
is a the same oem version that one has been installed by the manufacturer of my laptop hp
replaced hard drive and installed an oem version
On Sunday, October 7, 2012 18:28:49 + 0000, James allan strong wrote:
replaced hard drive and installed an oem version
It can be exactly the same, but the version of HP is an OEM version
Too much.You bought an OEM version? Why? Why don't you use the version of HP?
Ken Blake, Microsoft MVP
-
I still have my shop picture, serial number, can we recover photo shop?
Ron
Don't remember version,
probably the most fundamental.
Ron
-
Start an Android application that has been installed with navigateToURL()?
I saw a mention of a Java called 'intent' method, but I don't know how to implement this in AS3 (Flash or Flash Builder).
I am launching a SWF that can be launched via the load() method. For some reason even if I post the SWF file in a wrapper HTML and separately using the Flash debugger, when I try to use the load() method it does not load. I get a few AS3 errors when debugging that have to do with Classes using the SWF file.
So I thought, if I installed the apk from the SWF file and launched the apk with navigateToURL, it should work. But I need the right arguments. I have also considered fscommand. When I say arguments, I guess I'm talking more about the specific file name and path that the installed Android app is registered to the name.
Thanks in advance,
Markerline
you are probably a reference to the scene or something on stage BEFORE your loaded swf is added to the stage. that the why you have no problem when you test the swf as a stand-alone file and you have a problem when loading it.
to remedy this, use an Event.ADDED_TO_STAGE listener before trying to refer to the foregoing. If you do not understand the question/how resolves, copy and past the first 90 or so lines FontExtrusionDemo.as
-
Windows Update automatically ran yesterday on my Vista 64 Home Premium SP1 system. Today, I can't run any Office Applications. I get an error popup that says: "the application failed to start because its side-by-side configuration is incorrect. Check the log of events applications for more details. »
I learned how to use Event Viewer and found that a mistake by-side happening and a manifest file has been altered.
The file is: x86_microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.3053_none_d08d7bba442a9b36Where can I get a clean copy of this file? It is just a simple XML file. Do a system restore is not good.
Hello Astroguy,
Thank you for your response back!
Good to know that you have done a repair install. What I would do is run the SFC scan, because you performed the installation of repair recently the chances are that the SFC scan should be good. If there is a problem, it will signal you when finished.
Then I would go to Windows Update to check if he has new updates and/or try to update all those who did not. If you still get the updates that do not please let us know what he's trying to put up-to-date and error.
Thank you! Engineer James Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.
-
Windows 8 is installed on the wrong partition
I just opened my Ideapad u430 and immediately noticed that the windows that OS has been installed on the 500 GB sata drive instead of the SSD. I am sure that the whole point of the SSD part has been to install the OS on it to speed up performance. Tips on how to transfer the OS on the other side of the partition without the original disks?
Well, no, in my humble OPINION, but you may be able to make it work for your particular needs.
Size - 24GO - confirms that it is a caching of the road, and the operating system has not been installed on the wrong partition.
Z.
Maybe you are looking for
-
my plugin update checker has been working well, so I know this isn't the problem. the problem is that when I update my flash player id stops at 95% or 96% and will remain like that until I close firefox and when I close firefox it then finishes updat
-
videos start but stop even if its continuous
Videos will start sound but the video stops while the sound continues. If I move my pointer on the video, it will pass to where the progress bar indicates where the video at its current time of reproduction. How can I solve this problem?
-
Satellite A500 loses the same battery power is OFF
Satellite A500/01mhnx model.When I load completely to max and let that stop you it completely, after about 4 days, it says only about 2% of the available power.Is this normal because it is a new unit? All opinions and comments welcome.
-
Windows Firewall and Mcafee won't work?
I have mcafee antivirus more and everything works on it except for the firewall, when I try to turn on it turns itself after 2 seconds. I tried to turn my windows firewall on and just says cannot change some parameters and then I went to advanced to
-
Constrained nonlinear adjustment in V8.5 - non optimized result
Please can someone could give me information on where I can flick up with the restricted non-linear curve adjustment function? A little history: I have data that must match a resonance curve. I can adjust the curve to the data, but the results are no