My laptop says that the system has detected that a cooling fan does not work correctly

My laptop cooling fan stop working

If you haven't cleaned your laptop since you bought it, it can y dust/dirt clogged in fans, then he must have stopped working.

OR

In case if you overloaded some cell days with intensive, ongoing use of heavy tasks running.

Check if you have disabled the fan of the BIOS settings.
To access the BIOS settings, press ESC when the laptop starts.

Also apply thermal paste and carefully clean the motherboard of the laptop, entered air, etc.

Tags: Notebooks

Similar Questions

  • My HP laptop cooling fan does not work.

    Okay, so. I have a HP Pavilion 1145sg g6. It worked fine all morning, and then I put sleep temporarily (about ten to twenty minutes). When I went to turn it on, the screen was black and he said something along the lines of

    "the system has detected that a cooling fan does not work correctly. Suite operation is not recommended at this time... may result in unpredictable behavior that may result closed random, loss of data or damage the system as possible. »

    Then after a few seconds it stops completely. There is an option to continue with the summary of the system and I clicked once on it, but she didn't go through completely for allowing me to use my laptop properly (I arrived at my wallpaper and it stopped).

    This has never happened before, and I never had any problem with my laptop, like this before. I have had him since last August, and it worked pretty well through until today. Of course, the system sometimes, accused but nothing serious, for the most part just aggravating.

    How can I fix?

    Someone said here that they stung the fan with a hairpin and it started working. I took a toothpick and switched my laptop and tried to move the fan and the fan started WALLA on! I noticed that a lot of dust in there and that's probably the culprit first event hough I keep this laptop clean every day, this darn dust is sneaky and small. If you use a toothpick, make sure not to break anything especially the toothpick. last thing you want to do is cause more harm. Now that I think I don't remember when the last fan worked and if it wasn't for the message that popped up today I would not of the same notice I wasn't to hear the fan because last week I said "wow is not the substance of this portable super hot feeling", but I just thought that my fiance was simply playing games on the computer for too long and that's why he was hot. He never closes the computer off smh. in any case, I'm very happy I read this post of a person using the PIN to hair. That's what forums are all about. Help each other. I hope it works for you. Be gentle, try pushing the way fan propellers in clockwise. Use a flashlight to see if dust or anything like that is by the way to allow the fan to run its on.  I blew in the vents, but it did have almost all of the dust of the road.  All of these messages, it seems this is a common problem. Good luck

  • My DVD player does not work and all the information I can find is "this device does not work correctly.

    Hi, I have Windows Vista and I use a computer laptop Dell studio. When I insert a disc into my CD/DVD drive, the drive spins and it looks like it is about to start and makes the same noise start several times and then just stops. My computer does not record that there is a disc there. If I double click on the DVD drive in 'My computer' it ejects my disc and says "insert the disc in drive E".

    I went on the 'repair' Microsoft online scanner and it told me that there is a problem, but he can fix it. In Device Manager, under CD/DVD-ROM readers I have Optiarc DVD +-RW AD - 7640S. Under device status - general - properties, it says "this device does not work correctly. He also says that I have the updated driver.

    I even uninstalled the driver as a last resort and then restarted my computer. It reinstalled the driver for me, but there was no change. Please help me!

    Hello

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
    Setup after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry
    entries that do not fix the resolution of problems and those who "could" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and the
    correct registry entries for your car.

    Here are the keys in my opinion, are those in question - for the CD/DVD drive of course subkeys as
    There will be other subkeys in these keys. Do not forget to ask involved specific keys as well as the
    Parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • I have a Samsung SGH T305 phone with phone cable to connect to the usb port on my pc. It does not work correctly, but now how to recover photos from the phone?

    I have a phone Samsung SGH T305, but not internet access for my phone.  Just a phone with a camera.  To transfer pictures to my PC, I connected a usb cable and PC.  I can't send them to my e-mail through the cable.   I don't know how to retrieve pictures from the camera.

    Hi, CarolW04,

    See if that helps

    http://www.Samsung.com/us/support/SupportOwnersFAQPopup.do?faq_id=FAQ00032825&fm_seq=32993

    With my LG, I used a memory card and move the photos to the card.  The device must be queued for mass storage until you will see the folders using the usb cable.  If you use a memory card, don't forget that it snaps into place.  Otherwise you will never see the folders if is not installed correctly.

  • Windows says that my index finger does not work

    When you perform a search in Outlook, I get an error that it is always indexing.  I tried all the patches, but when I go in the options of indexing, it says index is not running.  The only option I have is advanced and there is the default settings.  This did nothing and I can not turn Indexing on the back.

    Hello mtuckerman,

    Thank you for using the Microsoft answers Forum

    Outlook always has this problem or is it the first time that this has happened? We suggest you check to see if the Windows Search Service is running. Go to start > >(Classic View) Control Panel administrative tools > Services. Scroll down the list and make sure that Windows search is set to automatic. Open the service by double clicking on it, then choose automatic from the Startup Type. Once it is restarted, restart the machine for good measure. It may initially take a little while for Outlook to index if you have a lot of information in your e-mail software.

    Let us know if that helps.

    Judd
    Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

  • I can check a message that my CPU fan is not working?

    A few days ago I got a message that my CPU cooling fan not working properly and I should check it out. but the next time I logged in that I have no message of second check of my first message. I can interogate my computer to check the first message and if so, how?

    Hi DavidDudley,

    You may need to contact the manufacturer of the system or consult the manual supplied with the computer to test if the CPU (central processing unit) cooling fan does not work correctly or not.

  • my laptop HP Pavilion product g7 #A7A43UA #ABA cooling fan is not worki

    My cooling fan does not work properly and I have already installed the new version of the BIOS HP Pavilion product g7 #A7A43UA #ABA can I use a fan to minimise damage?

    hope someone can answer my question thank you

    [s/n removed for privacy]

    How old is your machine? It is under warranty?  Have you tried to use a can of compressed air in the opposite direction of the normal airflow with the machine?  What do you mean by not working not properly?  You have an error message? The temperature of your laptop is too high?

  • Satellite A10 S203: the CPU fan does not work properly?

    I have toshiba satellite a10 s203 and the cpu fan does not work correctly. What can I do about it?

    Hi SACRIFICE them.

    Here are some possible solutions to this problem of fan.

    1. When you have installed a base installation of MS (not the Toshiba Recovery CD) you need to install the Toshiba Power Saver and others utilities from the CD tools & utilities. The energy saver is responsible for the control of the fan.

    2. If you have a recovery based OS, you can update the energy saver of http://eu.computers.toshiba-europe.com site Web Toshiba under Support & Downloads - Download Driver

    If please check this and an answer then follow the next step!

    CAMPino

  • My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

    My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
    Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
    The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
    I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
    How can I force to load this driver?

    I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
    So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
    Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

    You could any body help me to find the source of my problem?

    Thank you.

    These are all good things:

    *****************************************************************************
    * *
    * Bugcheck analysis *.
    * *
    *****************************************************************************

    KERNEL_DATA_INPAGE_ERROR (7A)
    The requested page of kernel data could not be read in.  Usually caused by
    a bad block in the disk controller or paging file error. See also
    KERNEL_STACK_INPAGE_ERROR.
    If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
    This means that the disk subsystem has suffered a failure.
    If the status of the error is 0xC000009A, it means the query failed because
    a file system has failed to move forward.
    Arguments:
    Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
    Arg2: ffffffffc000009d, error state (state code of e/s normally)
    Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
    Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

    Debugging information:
    ------------------
    ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
    DISK_HARDWARE_ERROR: Error occurred with disc material
    BUGCHECK_STR: 0x7a_c000009d
    CUSTOMER_CRASH_COUNT: 1
    DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
    Nom_processus: System
    CURRENT_IRQL: 1
    LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
    STACK_TEXT:
    fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
    fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
    fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
    fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
    "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
    "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
    fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
    "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
    "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
    STACK_COMMAND: kb

    FOLLOWUP_IP:
    NT! : FNODOBFM: 'chain' + 50080
    fffff800'02c7fcac cc int 3
    SYMBOL_STACK_INDEX: 1
    SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
    FOLLOWUP_NAME: MachineOwner
    MODULE_NAME: nt
    Nom_image: ntkrnlmp.exe
    DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
    FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
    BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

    And this page explains what you have:
    http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
    (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

    It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

    This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
    Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

    SC Tom

  • P2715Q, "the system has detected a link failure.

    Just got my new DELL P2715Q monitor and I have the same problem. The monitor is connected to a TriX R9 290 (no X) via the DP-MiniDP cable supplied with the display.

    When I "wake up" the monitor of fashion 'sleep', I get the same error:
    "The system has detected a link failure and cannot set the resolution rate or refresh rate requested on your DisplayPort screen... "- the resolution is fine (4K), but all my icons and position Windows & sizes are reset to zero, as the display was turned off at some point during the day before and from operating system Windows are moved to 640 x 480.

    The display is not connected to a USB port.

    Display: P2715Q
    SN: CN-00GT67-74445-537-434 L
    GPU: Tri - X Sapphire R9 290
    Connection: DP 1.2 released in Mini-DP on the monitor.
    OS: Windows 7-64 bit (fully updated)
    Video driver: 14.502.1014 - a 150331, 1 - 182333E
    Windows power management: high performance. The PCI-e link status: PM: Off
    Monitor purchased from a reseller.

    I also tried:
    -Different cable (DP - DP).
    -Different video driver (catalyst Omega 14.12).

    The problem also arises when I turned off the monitor of its switch and let the computer - when I turn on the monitor after about an hour - the icons and windows apps are reset as as the monitor was at 640 x 480 at some point. Could you please give us with a solution to this problem? I really hope you can help me because I can't do my job until I fix this. Apart from that, the P2715Q is the best monitor I've ever seen.

    Kind regards
    Peter H

    I had the same problem.

    Buy a certified DP cable seems to have solved the problem.

    At present, there is only one cable of DP - DP 1.2 certified market.

    This is the list:

    www.DisplayPort.org/Products-Database

  • Im trying to load the update of Mac OS x Server combined software and it says that my disk volume does not meet the requirements of the software

    Im trying to load the update of Mac OS x combined Server software on my Mac Pro Tower 10.7.5 worm and it says that my disk volume does not meet the requirements of the software? Has anyone ever come across this problem?

    You are running a Mac OS X Server software? If so, which version?

  • Satellite P100-324 - GPU overheating due to fan does not work in the operating system

    Hello world.

    While trying to solve the problem of RAM of 4 GB ([this thread | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=28374&tstart=0]), I meet another weird thing - gpu overheating due to fan does not work in the operating system.

    Now, I restored the XP MCE using the Toshiba Recovery and I was VERY surprised to see that the problem still exists! As soon as loading the system GPU fan stops, and there is only tranquility. The application load is heavy on GPU and reaching 104 results by reducing its GPU and MEMORY clock values and NOT in the activation of the fan.

    The same thing happens in 64-bit gentoo. ACPI can be turned on or off, it is not serious, the GPU fan always dies as soon as the system load. In non-OS environments (bios, program of recovery, etc.) the fan works fine, GPU cooling from time to time.

    This problem occurs in versions of BIOS: 2.40, 4.00, 4.20.

    Any help would be greatly appreciated, since this laptop is my main working tool and I can't let go 14 days (service).

    I saw in your other thread that you have updated the BIOS and you have installed several different OS.

    Fact is that the BIOS v 4.2 package contains BIOS 32-bit and 64-bit OS.
    Your laptop has been preloaded with Win XP MCE 32 bit. Please use the 32-bit BIOS if the original XP MCE running on the laptop.

    Best regards

  • my iPhone 6s has problems with the GPS when I use some applications, it does not work well and give especially the bad road. Can someone help me?

    my iPhone 6s has problems with the GPS when I use some applications, it does not work well and give especially the bad road. Can someone help me?

    My iphone 6 has started having the same problem. Its literally the GPS. Saying that it does not find me at all. Ive seen say location for more than an hour in the suburbs of chicago. It started to happen to me after I downloaded the latest update for the iphone. I hope they react and let you know what is happening because I'm dying to know as well.

  • I run the program "TuneUp utilities" and I recently received a notification of the statement that "the BHDrvx64device does not work correctly.

    I run the program "TuneUp utilities" and I recently received a notification of the statement that "the BHDrvx64device does not work correctly" program proposed to update the driver, but there is no provision in any of the dialog boxes.  Windows Help and support says: help for this program was created in Windows Help format, which depends on a feature that is not included in this version of Windows. However, you can download a program that will allow you to view help created in the Windows Help format. All this brought me here, please, how to fix this?

    The last thing you want to do is install and run any third tuneup/Optimizer program.

    In the worst cases of such utilities can cause system failure or program, uninstall it, having restored firstly of the changes he could do.

  • Xbox 360 wired controller works only with Windows 8. Xbox 360 Assecories status when I click on it says I have it has been changed or moved, and will not work.

    I have a controller wired xbox 360, not one of these pieces of plug. I put the USB controller and installed the device. However, it does not work. Xbox 360 Assecories status when I click on it says I have it has been changed or moved, and will not work. I have not touched. When I search for a download for Windows 8 all get them are downloads for Windows 7 and below. It's a bit frustrating to not be able to use it. I would be very happy to help.

    Original title: windows 8 wired 360 controller

    I found the problem. I had the appropriate controller and installed the device correctly. This is the program that runs the unit that had either corrupt or missing files. I uninstalled the program and then installed from the Microsoft Download page. Now he works currently. Thanks for the support.

Maybe you are looking for