My MacBook starts to turn itsself when I plug in power. Help please.
Whenever I plug in the power cable for my MacBook (2016) it turns on itself. Energy settings are at default settings. I don't know if the hardware or software problem.
Do you mean that it stops when it is not plugged? If so, it's because your MacBook has been damaged by moisture! Energy settings do not work? Try putiing your light up! Tell me if it still does not.
G apples
Tags: Notebooks
Similar Questions
-
I have a laptop HP Compaq 6710 b... Its more than 6 years...
The problem is really annoying... The laptop powers on only when I force taken into the spindle of the charger and the laptop works very well after that...
But the laptop never turns on when I try to power by pressing the power button!
I did not understand the reason why...Any thoughts on this problem? Help!
There are no settings in the BIOS that affect the use of the power button.
The power button works at the level of the material (firmware).
By pressing the button translates the action of the Commission of the conditions of the logic system. There must be voltage at specific points in the power circuit. If the voltages are not present, then the power button does not work. This can be caused by a failure resistance, mlcc capacitor or a bad solder joint, if the power button has been tested and shown to work normally. Fluff even could cause this to happen. This can help out-performed by Visual inspection and using a multimeter.
-
I have an ipod touch that needs to be picked up by itunes. When I plug into a wall outlet, it lights up and told you to connect to itunes, but it not turn on when I plug it into my computer. Or my computer will recognize any device connected to the usb port. I tried another ipod to check the usb ports work and they are. Ive run out of ideas. help please
Hello
Check with iPod Support and Forums for more information if necessary.
-IPod support
http://www.Apple.com/support/iPod/iTunes and iPod Support
http://www.Apple.com/support/Each iPod - iPod help & Technical Support (part 3)
http://www.EveryiPod.com/iPod-help/index.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
HP-G62226TU: my laptop won't turn on when I push the power button
Hello
My laptop does not turn when I push the power button / stop and nor adjacent to the plug adapter lights turn on when I put the power supply. It behaves like completely dead. I pressed the button for 30 seconds as suggested in the following thread.
My laptop is 2.5 years old and was working fine without any problems so far.
Please suggest.
Thank you
Himanshu2303 wrote:
OK... I learned to get the motherboard changed. How much it will cost in India for my laptop?
What do you suggest I should do?
How much will it cost in India? I have no idea. I live in Europe.
I suggest to ask a repair shop of PC or laptop.
If the cost of repair is more than 50% of the current value of the laptop, you would be better sourcing of a notebook replacement.
-
My laptop (presario CQ20-320TU) turn directly every time I plug the power cord without battery. What is the solution?
Hi there @emonsonjaya,
Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.
I understand that your notebook is turn on/off automatically when it is plugged. I'm happy to help you.
I would recommend that you look at your BIOS, especially in power options and check if your BIOS has a setting option on automatically. If yes it change at your convenience. Another option would be to update your BIOS and see if that solves it.
Here is the page of support for your model and, if necessary, give it a try, it will automatically download the file if you click on the link. You then need to run the executable file of your current download folder.
HPQFlash for HP Notebook System BIOS (68PHU) - Microsoft Windows-Based
If you are having problems with an update of the BIOS, you can always restore it, using the following:
I hope this helps.
-
my iphone 6 fell into the water. won't turn on after that I dried it all day. What should do? Help, please
As you tried to turn it on it was still wet, the damage is done now.
Now, your only alternative is to call Apple and make an appointment to examine.
They will probably suggest that you buy one out of warranty replacement for her.
-
SCREEN FLICKERS WHEN I PLUG THE POWER CORD A/C
Can someone help me with this problem. My screen flickers when connected im playing games with my a/c power cord. Howerver when I remove the power cord, it works fine on battery. Also my battery almost won't charge at all with my laptop running, but when I put into hibernation or to stop it charges more quickly. Would appreciate any help as soon as POSSIBLE. Its a Dell Latitude E6400, windows 7
Diagnosis
The video "Refresh" is switching between 60 (on food) and 50 Hz (on battery), and the screen goes momentarily empty.
Solution
So what about current alternative, office > right click > properties > settings > advanced > monitor. Here, under the display settings, set the refresh rate of the screen at 50 Hertz. After you apply these settings, the flashing problem gets fixed.
-
My Acrobat Standard starts to turn pro when installing
No matter how to install an msi package or manually, it continues to turn to the PRO version at first boot.
I tripled to check the version downloaded from the deployment tools and also via user upload method. No dice!
What Miss me?
Any help will be much appreciated.
Thank you
Download the standard setup to a new directory. Use this new directory when you launch the installation file.
-
Phone starts to turn on when movement
After ios10 update my phone starts spinning movement
Tap Settings > Messages and then slide down and toggle OFF lift to listen to .
-
Computer screen turns off when I plug an HDMI cable
Initially, I had both my tv and computer off. I plugged the dvi to tv and the HDMI to laptop and turned them both on. I had no problems using my laptop I tried to synchronize the computer to the TV. However I must have accidentally hit something in the graphics options as my laptop screen went black. I unplugged my laptop hdmi cable and the screen returns to the top. But now, for some reason whenever I plug the HDMI cable for the laptop, the screen goes black. When I take it on it the screen comes back to the top. I have something that is originally for this change? Any help would be greatly appreciated. Thank you
Try pressing alt + F5
-
Satellite Pro 6100 turns off when I connect the power adapter
Satellite pro 6100 works well up to this I put AC adapter / CC, then turns it self
Any ideas would be appreciatedsee you soon
Hello
You use original Toshiba AC/DC adapter or another?
What happens if you connect the AC/DC adapter, while the laptop is turned off?It s really strange problem, but I think that is s TI associated with AC/DC adapter or the motherboard itself
-
Satellite C50-B-12V: mic turns off when I plug the headphones
Hello
I recently bought a computer laptop Toshiba Satellite, Satellite C50-B-12V
I'm really happy with my new lap top - thought I am facing a problem.
It seems that the port to plug in headphones and the port to plug in a microphone is the same. so, if I plug headphones wireless for a Skype call, the other party can not hear me.Is there anyway that I can adjust the computer so that it shouldn't be a problem?
Again, I would be able to plug the headset on my computer to hear my interlocutor better - and who have not cause the other party cannot hear me.
Hello
This integrated headphone / microphone port equipped with a plug of 4 section (identified with 3 black rings)
You have two options to solve the problem mentioned.
You must use a headset / microphone with jack combo or you could buy an adapter 'Y' which can connect your current helmet with separate microphone and speaker back to the headset / combo jack.Something like that:
[Y audio / headphone | http://ecx.images-amazon.com/images/I/41Y59zwJxcL.jpg] -
MacBook / J4580 All in One / software Parallels - does not PRINT - HELP Please
I'm going to lose my job in real estate - I have a Macbook - when I'm on the side of Mac - the printer works - and print. However, when I'm in Parallels - it does not recognize - only get the message "printer error". Real estate agency associated with the elements run only windows - so I spend a lot of time in the analogies. Our it guy at the office said to make sure I have install the CD on the side, parallels - but this doesn't work either. Called the Apple Support - they could not answer for Parallels - cost of Parallels for their support - so I will try this forum first, before I have to pay to see if anyone else has encountered this. Thank you!
This can be a Parallels in question, but let's get XP work just before mess us with Paralalls:
Verify that you can access the web page internal to the printer by its IP address.
1. click on the 'Start' button--> printers and fax machines.
2. under print jobs, click on "add a printer".
3. click on 'Next' on the Add Printer Wizard window.
4. Select "local printer attached to this computer. Deselect "automatically detect and install my Plug and play printer." Click on 'Next' and follow the instructions.
5. now, select HP in the manufacturers list, select your printer in the list of the models of printers and click the button "next".6. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
7. Add the name of print spooler, and then click "next".
8. click on "next".
9. click on "Next" and "Finish." -
Hello world.
I have a laptop Intel i7 Toshiba Qosmio with 12 GB of RAM, a 3 GB Nvidia graphics card. Two 750 GB HARD drives. Windows 7 64 bit Home Premium edition.
I had to convert a video (in AE) of my camcorder Sony QuickTime then moka he could follow. The file size was 12 GB. I motion tracking with Mocha video 3000 frames have been followed. I have completed my project and when I go to make it takes about 15 or more minutes to return, but after the rendering of the entire system is completely unstable and requires a cold start. It makes the video fine, but the computer is unstable.
I was looking at the use of the RAM then that rendered and he used only about 15% of the 9 GB allocated for AE.
AE CS6 version 11.0.4
Can someone help me with this? I uninstalled AE and reinstalled and there are always the same. I have a small project, no less important than a case and it preformed fine. No problems.
Is the size of the files of great for AE? Could the movement followed with Mocha be a factor in the stability of EI?
No idea which continues, please help me.
Thank you.
I think I solved it. I created the new exact replica of my project that makes the computer unstable. I made it another 2 times, it takes 3 minutes and the computer is 100% stable.
So I think that the old project was corrupt or something because the new double that works perfectly.
So I call it answered. Thanks for all help, much appreciated.
Ron
-
I have display problems with a game that I just downloaded. The game is Annihlation Total; the game does not appear correctly. He works for a few seconds, all the graphics turn Rainbow and I can't seem to stop. Tried to run in compatibility mode; did not work. I hope there is a solution because this is one of my favorite games...
Hi razorbladeapple,
(a) what operating system do you have? And also to indicate the version?There is currently no information on the compatibility of the game with Windows 7.You can also try to check compatibility here: http://www.microsoft.com/windows/compatibility/windows-7/en-us/Default.aspx(b) is the display horizontal bar change only whem you play the game?(c) you have installed the updated display drivers?Some devices have drivers you need to install yourself. If you download a driver that is not self-installable, follow these steps:
You must be logged on as administrator to perform these steps.For more information, see: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly
Update drivers: recommended links
http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-linksContact GT Interactive and check what they have to say about the compatibility of the game with Windows 7 because they are the best people to offer support.
Aziz Nadeem - Microsoft Support
Maybe you are looking for
-
SMART short test didn't?
I have a HP Pavilion p6180t CTO desktop PC. I run Windows 7 64 bit My HP Diagnostic tool at the request of Maint. walked through the and I had an area that failed the test. It's the failure of "SMART short Test"... HD521-2W How do I get this resolv
-
Cannot acquire two channels?
I'm missing something... I can't acquire mutiple channels. It will work if I delete one of the channels.
-
Issues relating to Internet WRT110
It happens every morning when I wake up. I unplug my router & modem every night and in the morning that I plug them back in. My computer (or something else, that I have connected to it) has some problems with connection to the internet, almost as i
-
Keyboard does not work after authentication on the RDS Session host
When you connect to the RDS through the access portal or app keyboard does not work after authentication on the RDS session host. Offline authentication works very well, past will guide you to the RDS host, then when you try to reset your password, t
-
When you download MBAM (free version) all real-time protection programs have to be turned off to allow the download and install to be correct. I couldn't find the answer to this question. I noticed in the discussions on the forum that Windows Defen