My new Apple TV v4 does not smoothly on Airplay with my MacbookPro and Air laptops but with the iPhone and iPad Airlay gets so juddery and then goes off - laptop computer WiFi connections all that happens on clues?
Devastated to find that the new AppleTV works great on Airplay / mirroring with the iPhone and iPad devices but completely useless on the NEW laptops.
Trying to show any video for example utube creates immediately hop on the TV screen when you use the Macbook and in no time the WiFi connection is stunned.
What is going on?
I use ElCapitan, and the last 15 "16GB i7 Macbook MacbookPro and not expect a problem with streaming media.
Absolutely well on Airplay with bith an iPhone 6 Plus and also an Air iPad
This will be due to a network problem. There is a difference between mirroring of a phone/Tablet and grow to a full desktop in real-time
Mmake that there is no other activity (other streaming, web browsing, backup network etc.)
Try to connect the Apple TV via ethernet
To see a current state of the network to obtain a report of istumbler or similar. Look for the strength of the signal, noise, networks nearby
Test on another network
Tags: Apple TV
Similar Questions
-
my iphone 5 works if connected to my charger, when I unplug it it stays on for a minute and then turns off, I can activate it after that but it turns off again. you wonder if it's my battery. I have already restored the phone, but it did not work. Help
Most likely, the battery is broken. With AppleCare +, a replacement of the battery is free. However, without AppleCare +, a replacement battery will cost $79.
Apple-Support - iPhone - battery and power: https://www.apple.com/support/iphone/repair/battery-power/
-
Update KB937287 keep apearing that the only update, tried to install a lot of times, but does not work, tried it with the standalone version and it keeps apearing, when I install it does not display an error message, just say that again was successful but when I try to look for more updated it apears again.
Hi mayortom,
Thank you for visiting the Microsoft answers Forum.
You can follow the steps outlined in the article below:
Troubleshooting Windows Update or Microsoft Update when you are repeatedly offered an update
http://support.Microsoft.com/kb/910339/I hope that helps!
Thank you and best regards,
Abdelouahab Microsoft responds to the technical support engineer -
computer does not boot, blue screen with the message: Stop: 0 x 00000024 (0 x 00190203, 0 X 86949258, 0xC0000102, 0x00000000)
Hello
1 how long have you been faced with this problem?
2. don't you make changes on the computer before this problem?Start the computer by using the Microsoft Windows XP recovery console, and then perform a check disk on the file system.
To do this, follow these steps:
1. Insert the Windows XP CD in the CD-ROM or DVD - ROM drive, and then restart the computer. Select the required options to start the computer from the CD-ROM or DVD - ROM drive if you are prompted to do so.
2. once the Welcome to Setup screen appears, press R to start the Recovery Console.
3. If your computer is configured to dual-boot or multiple boot, select the appropriate installation of Windows XP.
4. When you are prompted to do so, type the administrator password and press ENTER. NOTE: In Windows XP Home Edition, the administrator password is blank by default.
5. at the command prompt, type the following command and press ENTER: cd system32
6. type the following command and press ENTER: chkdsk /r /p
7. remove the Windows XP CD in the disc drive.
8. Type exit to restart your computer.Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
-
Mr PRESIDENT, MY WINDOWS 7-32 BIT PC does not support to open 'Copy trans drivers install' to copy doc, to the iphone
Please help me solve this problem.
Hello
Thanks for posting the query on Microsoft Community. I'm happy to help you on this.
I appreciate if you could answer a few questions to refine the question and provide you with better assistance.
- Did you change the system before this problem?
- Do you receive an error message when you try to open it?
- Have you checked in uninstalling and reinstalling the application?
If this isn't the case, I suggest you to uninstall the 'trans driver install' and reinstall it again and check if it helps.
Meet us with information, so that we can better help you.
Thank you.
-
ICB does not break breaking set with the code when executing the test test sequence point
I just started using the testbed and I use it with CVI. I am running version 4.2.1 of testbed. I'm currently trying to set up my "*.c files" of project folder appropriate to compile and run under the simple testexe of test bench and also tried the normal sequence editor. Currently, I moved all the *.c files &.h taken in charge in the same directory where the testexec.c... .not sure if it's the best place to put it?... It seems to work OK. However, I saw a few problems once the program is running. Is to show signs cited in my CVI functions but it shows as not fatal execution error: "position of unknown source, library function error, Panel, bar menu, control or a table handle is invalid" before and after pop up window panels. I tried breakpoint to the line of code in a CVI file to the project title for additional information about the error, but it seems that the breaking point is not being invoked as it does NOT run in debug in CVI mode and rather an executable. Across the service installed on the project file are *.c and not *.obj. I appreciate anyones help and give me advice. Thanks in advance
DLL is the only way to interact with code C/C++ in TestStand, Yes.
-
New Apple TV remote does not respond
Brand new Apple TV (64 GB), everything is connected correctly, the initial Setup is displayed to select the language, but the remote is completely inadmissible. No activity of touchpad, no button, click answer. If I hold the top two buttons (menu, icon 'TV') long enough I can get Apple TV to restart, suggesting it is a communication between Apple TV and remote, but that's all I can do - no other distance activity whatsoever so I can't me past the language selection screen.
Any help appreciated - big anti-climax Apple TV until now!
If you have an older remote, it allows to set up Apple TV and then restore or you can try to restore if you have cable USB - C, otherwise return it for a replacement.
-
Manage identities does not 'from' addy align with the "sent to" addy when replying
I just installed 24.6 and used the 'import' of Eudora. Everything seemed to move pretty well, but I can't understand the ' sent to '. I tried in "manage identities", does not. The problem is you answer a list of mail and thunderbird wants to insert my dominant addy instead of the address who sent the original e-mail. It is a problem when the identity must be subscribed/registered.
He does not do it every time, sometimes it inserts the correct answer "from". Cannot make sense.
Something to do with the import?
something to do with where you are in the folder hierarchy.
This account will be the default SMTP is used when the selected account is unknown, so if you have a list of e-mail account and move them e-mails in local folders to the selected SMTP server will be the value by default, where as if you are in the folder of the account the SMTp response. It goes the same for identities.
I'm pretty sure that one of these modules will meet your needs https://addons.mozilla.org/en-US/thunderbird/search/?q=identity & cat = all & appver = 24.0 & platform = windows
-
Save to File.vi report does not work when integrated with the executable
Hello
When I use the NI_Report.lvclass:New Report.vi and NI_Report.lvclassave report to the File.vi, I can use successfully to create and excel spreadsheet so he was working at the developer.
However when I build the source into an executable, this no longer works. (The name of the file is built from the source, so I'm not using a dialog box)
It can, however, create a .html file, but it does not seem as tidy. Why is he not creating the Excel file?
Running developer suite 2009, tried the .exe on Windows 7 and Windows XP with the same effect.
Thank you
-
James
See the attached zip file, it works for me here, see jpeg images and build the application accordingly and let us know. Did not include exe file, because the file size is too big.
-
Kodak in a 2150 does not print wireless. compatible with the usb cable. Help
My printer prints not my lap top. It works already. I uninstalled the program and reinstalled and it still does not print. I turned off the printer for a minute and I turned my router for a minute and they turned back. I don't know what else to do. Help, please.
See if it helps:
Lost on printer all-in-one Wi - Fi
http://support.en.kodak.com/app/answers/detail/A_ID/2741/selected/trueThe guests to answer and follow the troubleshooting.
-
IPsec VPN Phase 2 does not. Need help with the debug output
Is someone can you please tell me why I can't establish ipsec Phase 2 negotiations. I'm trying to connect a 2651XM to a Pix 501.
Here are the isakmp debug and release of ipsec and configs. I checked the keys are the same. And sets of transformations look ok. No idea why its not working?
What is the bottom tell me?
===========================================================
01:32:37: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
01:32:37: ISAKMP:(0:2:SW:1): IPSec policy invalidated proposal
01:32:37: ISAKMP:(0:2:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
01:32:37: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
01:32:37: ISAKMP:(0:2:SW:1): IPSec policy invalidated proposal
01:32:37: ISAKMP:(0:2:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
===============================================================================
ISAKMP (0): start Quick Mode Exchange, M - ID - 1154286426:bb32fca6
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2224366689, message ID = 1503891776
ISAKMP (0): removal of spi 1629787524 message ID = 3140680870
to return to the State is IKMP_NO_ERR_NO_TRANS
pixfirewall #.
pixfirewall # sh crypto is
ISAKMP (0): start Quick Mode Exchange, M - ID 400184159:17da535f
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2649583861, message ID = 1778335964 a.
ISAKMP (0): removal of spi 4117818781 message ID = 400184159
status code returned is IKMP_NO_ERR_NO_TRANSkmp its
Total: 1
Embryonic: 0
Src DST in the meantime created State
1.1.1.2 1.1.1.3 QM_IDLE 0 0
pixfirewall #.
ISAKMP (0): start Quick Mode Exchange, M - ID 923039456:370476e0
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2163779852, message ID = 2746774364
ISAKMP (0): removal of spi 212465792 message ID = 923039456
to return to the State is IKMP_NO_ERR_NO_TRANSexiClosure of session
CCC cryp #sh
CCC #sh crypto isakmp his
status of DST CBC State conn-id slot
1.1.1.2 1.1.1.3 QM_IDLE 1 0 ACTIVECCC #ping 192.168.1.1
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.1, time-out is 2 seconds:
.....
Success rate is 0% (0/5)CCC #ping 192.168.1.5
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:
.....
Success rate is 0% (0/5)
CCC #debug isakmp crypto
Crypto ISAKMP debug is on
CCC #debug crypto ipsec
Crypto IPSEC debugging is on
Crypto CCC talkative #debug
detailed debug output debug is on
CCC #ping 192.168.1.5Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:
.....
Success rate is 0% (0/5)
CCC #.
00:51:24: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:51:24: ISAKMP: node set 1268073006 to QM_IDLE
00:51:24: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 1268073006
00:51:24: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 1268073006
00:51:24: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:24: ISAKMP: turn 1, AH_SHA
00:51:24: ISAKMP: attributes of transformation:
00:51:24: ISAKMP: program is 1 (Tunnel)
00:51:24: ISAKMP: type of life in seconds
00:51:24: ISAKMP: life of HIS (basic) of 28800
00:51:24: ISAKMP: type of life in kilobytes
00:51:24: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:24: ISAKMP: authenticator is HMAC-SHA
00:51:24: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:24: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:24: ISAKMP: turn 1, ESP_3DES
00:51:24: ISAKMP: attributes of transformation:
00:51:24: ISAKMP: program is 1 (Tunnel)
00:51:24: ISAKMP: type of life in seconds
00:51:24: ISAKMP: life of HIS (basic) of 28800
00:51:24: ISAKMP: type of life in kilobytes
00:51:24: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:24: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:24: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:24: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:24: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:51:24: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:51:24: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:51:24: ISAKMP: node set-429221146 to QM_IDLE
00:51:24: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-429221146
00:51:24: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:51:24: ISAKMP: (0:1:SW:1): purge the node-429221146
00:51:24: ISAKMP: (0:1:SW:1): node 1268073006 REAL reason «QM rejec» error suppression
Ted. "
00:51:24: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 1268073006: status = IKE_QM_READY
00:51:24: ISAKMP: (0:1:SW:1): entrance, node 1268073006 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:51:24: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:51:24: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the counterpart
with 1.1.1.3
00:51:54: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:51:54: ISAKMP: node set-500877443 to QM_IDLE
00:51:54: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID =-500877443
00:51:54: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID =-500877443
00:51:54: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:54: ISAKMP: turn 1, AH_SHA
00:51:54: ISAKMP: attributes of transformation:
00:51:54: ISAKMP: program is 1 (Tunnel)
00:51:54: ISAKMP: type of life in seconds
00:51:54: ISAKMP: life of HIS (basic) of 28800
00:51:54: ISAKMP: type of life in kilobytes
00:51:54: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:54: ISAKMP: authenticator is HMAC-SHA
00:51:54: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:54: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:54: ISAKMP: turn 1, ESP_3DES
00:51:54: ISAKMP: attributes of transformation:
00:51:54: ISAKMP: program is 1 (Tunnel)
00:51:54: ISAKMP: type of life in seconds
00:51:54: ISAKMP: life of HIS (basic) of 28800
00:51:54: ISAKMP: type of life in kilobytes
00:51:54: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:54: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:54: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:54: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:54: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:51:54: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:51:54: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:51:54: ISAKMP: node set-701693099 to QM_IDLE
00:51:54: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-701693099
00:51:54: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:51:54: ISAKMP: (0:1:SW:1): purge the node-701693099
00:51:54: ISAKMP: (0:1:SW:1): node-500877443 error suppression REAL reason "QM rejec.
Ted. "
00:51:54: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node-500877443: State = IKE_QM_READY
00:51:54: ISAKMP: (0:1:SW:1): entrance, node-500877443 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:51:54: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:52:14: ISAKMP: (0:1:SW:1): purge the node 1268073006
CCC #sh crypto isakmp his
status of DST CBC State conn-id slot
1.1.1.2 1.1.1.3 QM_IDLE 1 0 ACTIVECCC #ping 192.168.1.5
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:00:52:44: ISAKMP: (0:1:SW:1): purge node-500877443...
00:52:50: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:52:50: ISAKMP: node set 1186613650 to QM_IDLE
00:52:50: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 1186613650
00:52:50: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 1186613650
00:52:50: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:52:50: ISAKMP: turn 1, AH_SHA
00:52:50: ISAKMP: attributes of transformation:
00:52:50: ISAKMP: program is 1 (Tunnel)
00:52:50: ISAKMP: type of life in seconds
00:52:50: ISAKMP: life of HIS (basic) of 28800
00:52:50: ISAKMP: type of life in kilobytes
00:52:50: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:52:50: ISAKMP: authenticator is HMAC-SHA
00:52:50: ISAKMP: (0:1:SW:1): atts are acceptable.
00:52:50: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:52:50: ISAKMP: turn 1, ESP_3DES
00:52:50: ISAKMP: attributes of transformation:
00:52:50: ISAKMP: program is 1 (Tunnel)
00:52:50: ISAKMP: type of life in seconds
00:52:50: ISAKMP: life of HIS (basic) of 28800
00:52:50: ISAKMP: type of life in kilobytes
00:52:50: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:52:50: ISAKMP: (0:1:SW:1): atts are acceptable.
00:52:50: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:52:50: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.1.68.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:52:50: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:52:50: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:52:50: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:52:50: ISAKMP: node set-1113601414 to QM_IDLE
00:52:50: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-1113601414
00:52:50: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:52:50: ISAKMP: (0:1:SW:1): purge the node-1113601414
00:52:50: ISAKMP: (0:1:SW:1): node 1186613650 REAL reason «QM rejec» error suppression
Ted. "
00:52:50: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 1186613650: status = IKE_QM_READY
00:52:50: ISAKMP: (0:1:SW:1): entrance, node 1186613650 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:52:50: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:52:50: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the counterpart
with 1.1.1.3.
Success rate is 0% (0/5)
CCC #.
00:53:20: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:53:20: ISAKMP: node set 459446741 to QM_IDLE
00:53:20: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 459446741
00:53:20: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 459446741
00:53:20: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:53:20: ISAKMP: turn 1, AH_SHA
00:53:20: ISAKMP: attributes of transformation:
00:53:20: ISAKMP: program is 1 (Tunnel)
00:53:20: ISAKMP: type of life in seconds
00:53:20: ISAKMP: life of HIS (basic) of 28800
00:53:20: ISAKMP: type of life in kilobytes
00:53:20: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:53:20: ISAKMP: authenticator is HMAC-SHA
00:53:20: ISAKMP: (0:1:SW:1): atts are acceptable.
00:53:20: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:53:20: ISAKMP: turn 1, ESP_3DES
00:53:20: ISAKMP: attributes of transformation:
00:53:20: ISAKMP: program is 1 (Tunnel)
00:53:20: ISAKMP: type of life in seconds
00:53:20: ISAKMP: life of HIS (basic) of 28800
00:53:20: ISAKMP: type of life in kilobytes
00:53:20: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:53:20: ISAKMP: (0:1:SW:1): atts are acceptable.
00:53:20: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:53:20: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:53:20: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:53:20: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:53:20: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:53:20: ISAKMP: node set-1692074376 to QM_IDLE
00:53:20: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-1692074376
00:53:20: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:53:20: ISAKMP: (0:1:SW:1): purge the node-1692074376
00:53:20: ISAKMP: (0:1:SW:1): REAL reason for node deletion 459446741 error "reject QM.
Ed ".
00:53:20: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 459446741: status = IKE_QM_READY
00:53:20: ISAKMP: (0:1:SW:1): entrance, node 459446741 = IKE_MESG_FROM_PEER, IKE_QM_E
XCH
00:53:20: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:53:40: ISAKMP: (0:1:SW:1): purge the node 1186613650
00:53:42: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang
State of Ed down
00:54:10: ISAKMP: (0:1:SW:1): purge the node 459446741===============================================================================
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
pixfirewall hostname
domain ciscopix.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 10.10.10.0
255.255.255.0
permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 10.10.1
255.255.255.0 0.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
1.1.1.3 outside IP address 255.255.255.0
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 10.10.10.0 255.255.255.0 inside
location of PDM 10.10.10.0 255.255.255.0 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 1.1.1.2 1
Timeout xlate 0:05:00
Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR
p 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map 20 peers set 1.1.1.2
card crypto outside_map 20 game of transformation-Petaluma_VPN
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * 1.1.1.2 address netmask 255.255.255.255 No.-xauth No.-config-m
Ode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 md5 hash
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Telnet timeout 5
SSH timeout 5
dhcpd address 192.168.1.5 - 192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:8c0d4948407071d3515f1546cf8bc147
: end
pixfirewall #.
=========================================================================
CCC #sh run
Building configuration...Current configuration: 1328 bytes
!
version 12.4
horodateurs service debug uptime
Log service timestamps uptime
no password encryption service
!
CCC host name
!
boot-start-marker
start the system flash c2600-adventerprisek9 - mz.124 - 25d.bin
boot-end-marker
!
!
No aaa new-model
no location network-clock-participate 1
No network-clock-participate wic 0
IP cef
!
!
!
!!
!
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
address key crypto isakmp 1.1.1.3 cisco123
!
!
Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
!
map Petaluma_1 1 ipsec-isakmp crypto
defined peer 1.1.1.3
game of transformation-Petaluma_VPN
match address 100
!
!
!
!
interface FastEthernet0/0
1.1.1.2 IP 255.255.255.0
automatic speed
Half duplex
!
interface Serial0/0
no ip address
Shutdown
clock speed of 56000
!
interface FastEthernet0/1
10.10.10.2 IP address 255.255.255.0
automatic duplex
automatic speed
card crypto Petaluma_1
!
IP forward-Protocol ND
IP route 192.168.1.0 255.255.255.0 1.1.1.3
!
!
no ip address of the http server
no ip http secure server
!
access-list 100 permit ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255
control plan
!
!
!
!
!
!
!
!
!
!
Line con 0
line to 0
line vty 0 4
opening of session
!
!
endCCC #.
!
!
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
address key crypto isakmp 1.1.1.3 cisco123
!
!
Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
!
map Petaluma_1 1 ipsec-isakmp crypto
defined peer 1.1.1.3
game of transformation-Petaluma_VPN
match address 100
!
!
!
!
interface FastEthernet0/01.1.1.2 IP 255.255.255.0
automatic speed
Half duplex
!
interface Serial0/0
no ip address
Shutdown
clock speed of 56000
!
interface FastEthernet0/1
10.10.10.2 IP address 255.255.255.0
automatic duplex
automatic speed
card crypto Petaluma_1
!
IP forward-Protocol ND
IP route 192.168.1.0 255.255.255.0 1.1.1.3
!
!
no ip address of the http server
no ip http secure server
!
access-list 100 permit ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255Hi David,
Overlooking the configuration of the router, it seems that you have applied the encryption card to the wrong interface.
interface FastEthernet0/0
1.1.1.2 IP 255.255.255.0
automatic speed
Half duplex
!
interface FastEthernet0/1
10.10.10.2 IP address 255.255.255.0
automatic duplex
automatic speed
card crypto Petaluma_1
Given that the pix will attempt to build a VPN tunnel to 1.1.1.2 map encryption Petaluma_1 must be applied to FastEthernet0/0, not FastEthernet 0/1.
Let me know if it helps.
Thank you
Loren
-
My serial number does not work he begins with the letters.
My serial number does not work. It begins with the letters.
[NEVER SEND A SERIAL NUMBER IN AN OPEN FORUM.]
[personal information... [Mod - https://forums.adobe.com/docs/DOC-3731]
[This is an open forum, not the Adobe support, please do not post personal information]
This isn't a serial number to activate an Adobe product. Serial numbers for Adobe products have only numbers, 24 of them in 6 sets of 4. If you happen to find the serial number to be sure never publicly share since anyone can take and use it. Find the serial number of your product Adobe quickly
-
My Satellite A100 does not support SDHC cards with the internal card reader
Hello
My Satellite A100 can't stand my sandisk 4 GB SDHC.
'normal' SD cards are not a problem with the internal card reader, and there is no problem with the 4 GB sandisk SDHC card using an external card reader.is there a software solution?
regrads,
ItockI don't have the time to read the manuals for your model of laptop users, but can be registered to all supported cards. I guess SDHC not registered and not supported.
I don't know what you mean with the software solution, but as far as I know, update for multimedia card reader is not available.
-
FSX MULTIPLAYER DOES NOT HAVE MANY PEOPLE WITH THE SAME PROBLEM
I have a FSX I've always used the multiplayer mode for online flight, now a few weeks ago its been not conect, my internet is good, everything works but is not multiplayer, many people with this problem, tell us how to find a solution, we really like this multiplayer game
Hello
Thanks for posting your query in Microsoft Communities.
According to the description of the problem, it seems that you are not able to play Flight Simulator X multiplayer.
Please go ahead and read the steps mentioned from the link and later a update on the State of the question.
Microsoft Games: Multiplayer troubleshoot
You can also stay in contact with the Flight Simulator with the help of the link and check if it helps.
http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx
I hope this helps. Let us know if you need more assistance.
-
'Page' does not name a type with the given Code problem
Hello
I try the code on this page , but I'm getting 'Page' does not designate a type in the Test.hpp file with the following line
private:
Page * appPage;
Container * mRootContainer;
};
What could be the solution for this problem?
OK I solved this problem with the addition of bb::cascades with the page
Please take a look at the following codeprivate:
BB::Cascades:page * appPage;
BB::Cascades:container * mRootContainer;
};
Maybe you are looking for
-
Parental control &; YouTube
I turned on parental controls, and all of a sudden my Youtube app is gone, is anyway to prevent this app to disappear? I tried to allow youtube.com in the Web sites section to allow restrictions, but that did not help. Any ideas?
-
When I try to print a web page, the result is several partial pages. I tried to adjust the scale, but nothing seems to work. Where can I get this type of adjustment?
-
After each completed sequence execution to a file of the client's sequence, I would like to check the status of each step in that order. Based on the Statute, I want to do something. Currently, I have a sous-suite that is called at the end of each se
-
Crashing when trying to list errors
After doing a few storage a complex provision of application Labview code now refuses to errors in the list and I can't find. LabVIEW and then quickly ends. Everyone came through this with Labview 8.6.1?
-
preventivo per cavo codice D2M62 sas controller
Buongiorno mi servirebbe UN preventivo by price di UN cavo sas by codice DELL Dell Server T130 SAS line con D2M62. 5s risposta. Grazie