My PC detects that my Kingston card reader into the USB port but wont read SD card - why?

Several ports USB in my PC w/Windows XP see all my USB key and can read the data, but while "type" my Kingston card reader 4ports are recognized, it will not read the SD card. Why?

You should have installed service pack 3, a long time ago, but this probably isn't the cause of your immediate problem.  Until the last part of your response, I would say that you need to get a new card reader.  However, if the card reader works on another computer, something seems to be the issue.

What is the model of your Kingston card reader? It should appear on the label.

With the drive connected to a USB port, open the Device Manager (start > run > devmgmt.msc > OK).

Normally, you should see a number of entries in the category 'Disks' for the number of different locations in the card reader.  They probably will be named something like, "Kingston USB 2 HS-CF USB Device" and similar.  It should also have an entry in the "De Bus USB controllers" category that says "USB Mass Storage Device".

Check all the entries above.  If none of them display a warning icon (exclamation), double-click the entry and to report to what appears in "Device status" and "use of the device.

Right click on each of the entries corresponding to the card reader (i.e. one for each location in the hard drives category card reader and an in the category USB controllers USB mass storage device) and select uninstall.  After all, entries have been uninstalled, disconnect the player from the computer card and restart.  Now reconnect the card reader.  Windows should recognize and install it automatically.

NOTE: If you have a hard drive connected by USB, you must be careful that you uninstall the correct USB mass storage device.  The safest way to do this is to use the "Remove hardware safely" to stop your external drive and then disconnect it from the computer.  At this point, its entry will be removed from the Device Manager.

If the procedure above does not read your card before the card reader, I am ideas.

Tags: Windows

Similar Questions

  • AS3 how can you detect if someone shoots their camera into the USB port?

    In AS3 if the SWF Gets a hold of the camera of someone successfully and they begin streaming video everywhere and everything, but then halfway, either they wiggle accidentally their camera into the USB port, or the camera just sort breaks down, or something like that, how can detect you on the user side?  I tried using event listeners and different variables of Mark also every five seconds, but none worked. any of the public properties of the camera or its events seem to be acting funny of all when something happens like that.  And apparently you can just keep analysis the computer for devices (for a good reason, I suppose).

    Is there something I'm missing here?  Is it possible to detect the copy of a user of a SWF file (PF or AIR, but much more important still FP) when their camera has effectively stopped as the result of something goes wrong, like them what she wiggling the computer by mistake?  If so, how?  Thank you!

    Run your code and disconnect your camera. What are the common properties of it? Stop your flow? To return only a framework of specific color? These things can be used to detect, but you are right when you say that you can not detect more than a loss of packets from a NetStream object.

  • HP 15-f024wm laptop computer: laptop does not recognize the SD card into the usb port

    I don't have a sd card reader on my laptop but have used a map on her usb adapter and it worked. I had to make a full recovery, update and reload the browser and so on. HP has spent hours helping me to get back to his normal race car computer... but this issue remains and can't find what I need to do the usb - SD card reader. Yes, the usb port works as I use it for other things.  Don't know what I'm missing.

    Hello

    Your machine IS not card reader. His record:

    http://support.HP.com/au-en/document/c04420347

    which indicates:

    External ports:

    • Multi format digital card reader for Secure Digital cards
    • 2 superSpeed USB 3.0
    • 1 bus (USB) 2.0 universal series
    • 1 HDMI
    • 1 PORT RJ-45 (LAN)
    • 1 plug headphone-out/microphone-in the drop-down list

    Location:

    Everything you need: download Driver Realtek card reader and install it on your computer.

    http://ftp.HP.com/pub/SoftPaq/sp66501-67000/sp66959.exe

    For your question: all the USB ports work?

    Kind regards.

  • Upgrade laptop XP on the new home network. Shared for laptop drives. Now computer laptop poster not the zip drives that I plug into the USB ports.

    I have a xp desktop machine, an external hard drive, computer laptop xp and a computer laptop win7 on a network home via my Lynksys wireless router.  My friend attached external desktop.  Then shared these discs on the network.  He shared them as drives E and F.  I can access these drives very well.  The problem is that on the computer laptop xp now when I click on my computer if there is no zip drives or anything else connected to the computer laptop USB ports it does not show them.  If I go into Device Manager, it shows the mass storage device connected here.

    Another thing.  If external that are shared and the desktop machine is turned off the coast, I can click the icon to the desktop and it displays the zip drive, that I plugged.  It's like I need to rename or remap something?

    Hi crazypainter,

    When you plugin your USB device, just follow the following process:

    Rigth click my computer-> manage-> disk management.

    You will find your hard drive, cd and USB dirve listed player, you can do a right click on the drive letter and click on modify.

  • How to read the data in a device connected to the usb port

    Is there a class or object, or the piece of code in Java that is comparable to the PDQComm32.ocx and the mscomm32.ocx used in VB6? I need to know how to read the data of a device plugged into the usb port of the BBerry. Is it possible to use the BB to read data from a device via a usb cable?

    I'm new in Java and I'm looking for the opportunity to write a project to read the data in a device with this program that can turn on a BB instead of on a pc.

    Thank you

    Did you watch net.rim.device.api.system.USBPort?

    That's what the doc says:

    Provides access to the USB port of the device.

    Avoid using this class in applications, as it is not portable. On the contrary, if you need to access the USB port, use factory CLDC Connector to serve a connection.

    Rab

  • Why don't Windows (or the Photo app) read more a picture of the USB port?

    Why do Rt Windows reads only one photo at a time a USB plugged into the USB port?  I had imagined that the Photo app would be able to see the drive and move from one photo to another, but it does not work.
    I have tried using Windows Explorer to slect all the pictures, and then click right and select 'open' from the menu.  Only a single open photo.  He need to return several times to explore, click on the following picture, wait until it opens, etc..

    On my desktop PC (a Dell running Windows 7), Windows Photo Viewer will open one and then pass that one to what is provided for in the same folder, by clicking on the button "Next" or "previous."  Works with both files on the disk hard and files on a USB key.  Seems pretty obvious to me.

    Am I missing something?

    (PS: I'm sure that someone else asked this, but a couple of searches do not turn up quite the same question.)

    Last updated on 15/07/13: I managed to solve this problem. All I had to do was to rename the folder in the case to be 'Photos' instead 'photos.' It's a trick that I had read some time ago and had not followed. Once I renamed the mounted folder (because it shows on the C drive), the photos are visible in the Photos app.   Curiously, the photos appear but not the name of the subfolder. Not really a major problem, but a little... weird, maybe.

    Hi Benzman,

    1. what other app are you talking about where the photos are working properly?
    2. were there any changes (hardware or software) to the computer before the show?
    3. What is the format of these photos?
     
    I tried on my side, and it works correctly.
    a: I clicked on the Windows Logo + E to bring up Windows Explorer.
    b: then I selected all the photos and then right-click on it and choose Open.
    c: open photos, and then I click on the arrows to navigate to other photos.
     
     
    Good day!
  • Tips on how to get attached with Nikon D810 and Lightroom - I tried with the uSB cable but Lightroom does not recognize the camera. My memory card has no images on it that I read somewhere that it can slow things down if it has pictures on i

    I tried to use the uSB cable, but Lightroom does not recognize the camera. My memory card has no images on it that I read somewhere that it can slow things down if she has no images on it

    If you use Lightroom CC / 6 on a Mac OSX El Capitan you must update to the latest version of CC 2015.4 / 6.4. Problems with Nikon capture home has been fixed in the latest update, the lis below.

    Lightroom Journal | Tips and advice straight from the Lightroom team.

  • Error installing Microsoft NET Framework 3.5 Service Pack 1 Setup program has detected that this computer does not meet the requirements to install this software

    I need to install Microsoft NET Framework 3.5 Service Pack 1, as it is necessary to perform a Dell diagnostic Test, but I've been advised that: Setup has detected that this computer does not meet the requirements to install this software. Requirement: Windows install 3.1.

    However, when I look at the download page of Windows Installer 3.1 is not actually as for XP with SP3. I tried anyway and: Setup has determined that the version of Service Pack for this system is newer than the update you are applying. There is no need to install this update. Well actually it is there...

    Is there a way to get around this?

    See below articles for solution

    1 system requirements for the .net framework

    http://msdn.Microsoft.com/library/8z6watww.aspx

    2 download links for .net framework

    http://www.Microsoft.com/net/download

    or

    http://msdn.Microsoft.com/en-us/library/5a4x27ek

    3. top 8 resources for .net framework

    http://www.Microsoft.com/net/itprofessionals

    4 dependencies and Versions of .NET framework

    http://msdn.Microsoft.com/library/bb822049.aspx

    5 frequently asked questions
    http://msdn2.Microsoft.com/en-us/netframework/aa497323.aspx

    6. management of versions, compatibility and run side-by-side in the .NET Framework
    http://msdn2.Microsoft.com/en-us/netframework/aa497340.aspx

    Good luck

  • My laptop does not recognize that anything that is connected to the USB ports

    Help, please. My laptop does not recognize that anything that is connected to the USB ports.

    Moved from feedback

    Original title: problems with USB ports

    Hi Alba.

    1. who is the operating system installed on the computer?

    2. What is the brand and model of the computer?

    This issue may be caused if one of the following situations arises:

    • The currently loaded USB driver has become corrupt or unstable
    • Your PC requires an update for problems that could conflict with an external hard drive USB and Windows
    • Windows may be missing other problems hardware or software updates
    • Your USB controllers may have become corrupt or unstable
    • External drive can enter selective suspend
    • Your PC motherboard may need updated drivers

    I suggest to connect the USB device to a different USB port and check.

    You can run the Fixit provided in the article and the Coachman.

    Reference:

    Hardware devices do not work or are not detected in Windows

    http://support.Microsoft.com/mats/hardware_device_problems

    You can also try the steps in the link and check if it helps:

    Reference:

    Tips for solving problems of USB devices
    http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

    Note: Apply to Windows 7 as well

    Hope this information helps. Response with status so that we can help you.

  • Windows detected new hardware wizard appears each time I try to connect an external hard drive via the USB port.

    Whenever I try to connect an external hard drive into a USB port, Windows detected new hardware wizard will appear. He then not recognize the external drive at all. It does not appear in disk management. In Device Manager, it is listed as a 'device' USB bus controllers not. Under "other devices", there the question mark yellow and says the device is not configured correctly (code 1). External hard drive works fine on other PCs. It's a plug-and-play device. Port and USB cable work fine with other devices. Just this external hard drive has never worked on this PC.

    Hello

    I suggest that you try to remove USB controllers to the clean boot state and control.
    How to configure Windows XP to start in a "clean boot" State
    http://support.Microsoft.com/kb/310353/en-us
    Note: When you have finished troubleshooting, proceed as explained in the article to reset the computer to start as usual.
    See also:
  • "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

    "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

    1. my laptop - acer aspire 5030 - has been having this problem for the last five months.

    2. I tried everything including changing service pack, as we have xp professional, he has recently upgraded to vista business 32-bit with service pack 1.

    3 tried all the methods start the laptop after a few hours, remove the battery, press the power button for half a minute, and so on.

    4. I finally he formatted a couple of times, but the problem is not.

    5. later, I improved the professional system of vista and installed the latest security patches, but the problem remains

    6. now, I started to update its drivers, although the device is identified to be connected, but is not recognized. "the error message" not recognized usb device "appears. I try to reinstall the drivers or upgrade of drivers, it does not. It displays the message "the drivers for this device are to this day.

    7. initially, the connection of the device, the drivers are installed but still the device does not show in Explorer.

    8. I tried to change some registry values by merging a regedit file in the registry - for display devices that are not present; but still, it has failed.

    9. I then tried to delete the file infcache1.inf in c:\windows\system32\inf, but the problem persists.

    10. Subsequently, I tried to create another registry entry to "disable selective suspend" in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB by adding DWORD and assigning a binary value of 1.

    11. I tried later also to uninstall all the system devices including USB controllers, drives and the storage controllers, who must still without success.

    12. I tried to see if the drivers in safe mode, which they did not.

    13. I tried to delete the following registry entries =

    HKEY_LOCAL_MACHINES\System\CurrentControlSet\Enum | USB PORT; HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10318 & HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10200.  The computer does not have alow it.

    14. the BIOS indicates device pnp "disabled", which I also look for the BIOS settings, which do not allow me to change to change existing ones.

    15. I have not found the WINDOWS\SYSTEM32\drivers\USBSTOR file. SYS in my driver store. This affects the system?

    16. I also contacted manufacturers pnp devices that provided me with most recent and versions compatible drivers for my devices - namely an apple ipod & Seagate external HARD drive - but even after that the drivers are installed properly and the system rebooted the problem remains. Is this something to do with the updated playing driver registry entries does not after the update? OR is what registry entries are configured to only read the entries at the time of the installation of the OS?

    17. I also contacted local sellers who have suggested to me to change the "motherboard". This will help as a last resort?

    18. in the meantime I had also installed other operating systems to Linux - Fedora and Ubuntu; Full Windows XP - Home & Professional and Vista Edition. All these have been installed successfully but do not solve the problem of usb.

    19. I have also raised the original HARD disk & replaced by another HARD disk. also checked the power of all ihee and ehee usb ports to be at least 5 V. I also disabled the automatic deactivation of devices usb by the system. physical contact, ports and connecting cable is fine. the distribution of power is set at 10% for the ihee ports and 20% for ports ehee, which is what is should be the physical output is also close to 5V for all ports connected.

    20. all professional (hardware or software) should any solution for the problem of the usb ports on my laptop?

    Something that you haven't tried:

    How to fix USB device not recognized in Windows

    http://www.online-tech-tips.com/computer-tips/USB-device-not-recognized/

    I hope I could help

  • When I plug my portable hard drive to the usb port it does not read and display the contents...

    When I plug my portable hard drive to the usb port it does not read and display the contents...

    Hi deaza,.

    Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

    O trying to connect to another USB port to check if it works?

    O the hardrive shows in windows of the computer when you connect it?

    Method 1:
    If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

    Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

    Method 2:
    I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

    Method 3:
    If this does not help, then follow these steps:

    (a) remove all your USB devices. Use the safely remove the feature to turn them off.

    (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

    To open Device Manager, go to the link below and follow the steps:

    http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

    (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

    You can also navigate to the link below and follow the steps to install the USB device.

    http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

    I hope this helps. Let us know the results.

    Thank you and best regards,

    Srinivas R

    Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Is time Machine always being backed up to the folder My Documents/Desktop now that they have been sucked into the iCloud?

    Is time Machine always being backed up to the folder My Documents/Desktop now that they have been sucked into the iCloud?

    Yes. The files are still on the computer so that they will always be saved by Time Machine.

  • Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer?

    Is there such a thing as a USB wireless, that does not need USB cable upstream that goes into the usb slot in the main computer? I've looked everywhere but I can't find one. I hate the son, and I try to clear my desk of as many people as possible.

    # USB is cable only.

  • can I load that an omni 10 threw the usb port

    a 10 omni can be charged using the usb port?

    Hello

    The recommendation is to use the charger that comes with the unit. You can still use USB port to charge, BUT it can take ages to get a full charge, and this may affect your computer.

    Kind regards.

Maybe you are looking for