My PC startup error message: c:\Users\Administrator\AppDate\Local\TBHostSupport\TBHostsupport_0.dll

Similar Questions

• How can I fix the Error Message C:\Users\Buck\AppData\Local\WLetamp.dll

  These Messages at the point every time I start my laptop.

  Same answer as your other question.

  Duplicate thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/how-do-i-fix-an-error-message-that-comes-up-upon/58549bba-59c0-4e8e-9c43-7772a1f923c5

• RUNDLL error loading C:\Users\Gail\AppData\Local\Temp\fontftp.dll the specified module could not be found

  This message appeared on start up after I installed my new printer. How can I get rid of him? Thank you

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  This is the probably the result of malware then do a very thorough check and when the
  the system is clean see the following message to remove this error.

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  New Vista and Windows 7 version
  http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  Original version
  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Error loading C:\users\Brad\appdata\local\temp\cmmoiles.dll

  What is cmmoiles.dll

  I can't find anything about this file, see bing, google, drive c; nothing? I get this error:

  Hello

  Since its in a temporary area, you may have dodged a bullet. Better to delete the file, if it exists, then
  remove the error message.

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Autoruns - free - see what programs are configured to startup automatically when your system boots and you
  opening of session. Autoruns also shows you the full list of registry and file locations where applications can configure auto-
  start the settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Error loading C:\Users\Richard\AppData\Local\Temp\cerdr.dll. The specified module could not be found

  The PC boot-to top every morning, I get this message. Can I please ask for some advice on how I can solve this problem, thank you.

  Hello LewBut,

  I'd say go throught he link below and try the suggestions of the SpiritX MS MVP.  How long have you encountered this message when you start your computer?

  Error loading C:\...".dll" the specified module is not found.
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/error-loading-CDLL-the-specified-module-could-not/c21f0647-98EA-4170-9fca-90b5fcc5273a

  In addition,

  DLL of enforcement, error loading

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/run-dll-error-loading/02dbc0c6-fed0-4B7E-97ab-1245e9f43939

  Thank you

  James

• When I start my computer, I get an error message «Error loading C:\Users\jimhoss\AppData\Local\Temp\...» »

  When I start my computer, I get three error messages concerning three different files.  They all have the same path and they all say
  "Error loading C:\Users\jimhoss\AppData\Local\Temp\bsipi.dll".
  "Error loading C:\Users\jimhoss\AppData\Local\Temp\udilt.dll".
  "Error loading C:\Users\jimhoss\AppData\Local\Temp\mounINFO.dll".

  I have Malwarebytes and run it a couple of times and I remove all the files it detects as malicious, but I still receive these error messages when I start my computer.  I also have MS Vista.

  Hello

  They seem to be the remnants entered boot for malware.

  Malwarebytes is normally very good to remove things like that.

  The problem persists after scanning, take these startup entries:

  "How to use MSCONFIG in Windows Vista"

  http://www.netsquirrel.com/Msconfig/msconfig_vista.html

  You can also use this free program to do, too:

  "Autoruns for Windows V11.32"

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  See you soon.

• Error message: "error loading C:\Users\Sue\AppData\Local\WMPDBDL.dll the specified module is not found."

  I have an error message box that always appears at the start of my computer.  It says: "Error loading C:\Users\Sue\AppData\Local\WMPDBDL.dll the specified module is not found." I have a Dell Laptop Inspiron 1720 running Vista. I just 'X' it out and continue on but would like to get rid of it.  I don't know that it's touched something that needs correction.  Thank you

  Hello

  Google who provides virtually no information that suggests it might be the malicious program or a start remains for her entry search

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If the error persists after scanning use this program to out startup

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• On the start screen, I get the message: "C:users\acer\AppData\Temp\_ME124042\Python27.dll (error Code 5).

  Original title: Dll error

  At the start I, a screen opens with this message: "C:users\acer\AppData\Temp\_ME124042\Python27.dll (error Code 5).

  I have problems with the game to the top of the files as well. Error number 5 keeps popping and I can not install unless I have run as administrator. I can't understand this. Could I have some clarification on this? How to fix this?
  Help please.

  The bottom worked for me

  1. Open Windows Explorer.
  2. Paste this ( %UserProfile%\AppData\Local\ ) in the address bar.
  3. Right-click on the Temp folder and then Properties - Security tab - Advanced button.
  4. Click the button Change Permissions .
  5. Remove all permissions.
  6. Select the entry for your username, then click on Edit .
     • Include the permissions that can be inherited from the parent of this object.
     • Replace all permissions of child object with permissions inheritable of this object.
  7. Click on OK .

  

• Error loading C:\Users\gelwix\AppData\local\temp\

  How can I get rid of this message when I start?  Error loading C:\Users\gelwix\AppData\local\temp\

  Hello

  1. What is the version of the operating system installed on your computer?

  2 have you made changes on the computer before this problem?

  3. What is the exact full error message?

  Then follow the mentioned methods:

  Method 1:

  Use a tool like autoruns to locate the reference and delete it.

  Autoruns:http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Method 2:

  If you use windows XP follow this:

  Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

   

  If you are using Windows Vista or Windows 7 follow this:

  Perform the clean boot and check.

   

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  
  Please note:  After troubleshooting, be sure to start your computer in normal mode by following step 7.

   

   

  I hope that the above information is useful!

• Error loading C:\Users\Bo\AppData\Local\ukohixowe.dll is not a valid Win32 application

  Original title: ukohixowe.dll

  I have the following error message appears whenever I start Windows Vista:

  Error loading C:\Users\Bo\AppData\Local\ukohixowe.dll
  C:\Users\Bo\AppData\Local\ukohixowe.dll is not a valid Win32 application.
  In addition to the error message when my PC goes into mode 'sleep' & the monitor turns off, I am unable to wake up the screen saver.
  What is this error and how to fix it & the problem of monitor

  Hi Adrien,.

  According to the description, it seems that you are having problems with the startup error message and the computer doesn't wake up from its sleep.

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you perform the clean boot and check if the problem persists.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, be sure to configure the computer to start as usual as mentioned in step 3 of the article mentioned above.

  Method 2: Try the SFC (System File Checker) scan on the computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3: For the question about the computer is not waking from sleep, you may read the following article and check.

  A Windows Vista-based computer resumes the mode not sleep if you move or click a USB mouse as the computer is switch to sleep mode

   

  http://support.Microsoft.com/kb/930091

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• system starts with the following error: runDLL - error loading C:\Users\Hav\AppData\Local\Temp\hnszs0.exe

  Original title: runDLL Error Message

  When I start the computer I have an error: runDLL - error loading C:\Users\Hav\AppData\Local\Temp\hnszs0.exe - the specified module could not be found.  How can I fix it?

  Hello

  1. don't you make changes to the computer until the problem occurred?

  I suggest you to try the steps below and check if it helps.

   

  Method 1: Try to start your system in safe mode and check if the same problem occurs.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

   

  Method 2 : If the question does not exist in Mode safe mode then try to put your computer in a clean boot state.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

   

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  In addition, please see the link below with a similar problem reported.

  Help with RunDLL error on startup

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/help-with-RUNDLL-error-on-startup/e929b39c-55d1-4EA4-A5A0-b38733286d84

  Hope this information is useful.

• Get error in Vista, error loading c:\Users\Marie\AppData\Local\usbcrtRpl\sysWebman.dl lthis specified module could not be found

  Recently received a message from RunDLL when I start.

  Error loading c:\Users\Marie\AppData\Local\usbcrtRpl\sysWebman.dl lthis specified module could not be found.

  Ive already scanned for malware using Malwarebytes found nothing.

  What should do? Help, please. Thank you in advance.

  * original title - how to get rid of the error message at startup upwards *.

  Hello

  Cannot find this file on Google so you probably dodged some software malware and you should do a
  very thorough control. Message on how to remove the error message if still it y
  After the audits of malware.

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often
  easy to detect malicious software often comes with a much harder to detect and remove the
  payload. So its best to be now too thorough than paying the high price later. Check
  with an extreme overdose point and then run the cleaning only when you are very
  that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap you start, however, you should
  also run in regular Windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/products/malwarebytes_free

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with the other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here or
  Use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  -----------------------------------

  Original version is now replaced by the Microsoft Safety Scanner
  http://OneCare.live.com/site/en-us/default.htm

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  ----------------------------------

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing system
  files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Error loading C:\Users\User Name\AppData\Local\HpWebNotifier\SyncNetOffice.dll

  Whenever I start my computer, I get a pop-up that says: "error loading C:\Users\User Name\AppData\Local\HpWebNotifier\SyncNetOffice.dll.

  My computer and the printer work fine, but this message is boring.  I can't understand what the problem is.  I wonder if it is a question of an old printer that I used to be connected that I already uninstalled.  Does anyone have ideas how I can fix this problem?

  Thank you!

  Hello lisabar90,

  What operating system is your computer?

  What model computer do you use?

  Try this click Start, then hit and run and type msconfig.

  (if your computer does not have a run type msconfig in the search box and click on the application)

  Go to the Startup tab and see if you can see a reference to this place. Uncheck the box and restart your computer.

  After return your results.

• C:\Users\Owner\AppData\Local\Temp\MSIMG32.dll is not designed to run on Windows or it contains an error.

  So I try to install this thing for this program called Mypublisher so that I can make a photo book... But it keeps giving me this message. The entire message is "C:\Users\Owner\AppData\Local\Temp\MSIMG32.dll is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or support software provider. "I've never used this program before so I don't know how I could use the original installation media. He also gave me this message when I tried to update quicktime, I think that's what it was. I have tried everything I can, but I'm not a computer genius so I don't know what to do to... Any help? Thank you!

  Original installation media means the Mypublisher cd or downloaded installation file

  Try their http://www.mypublisher.com/customerservice support

• Error loading C;\users\Toshiba\appData\Local\SMBDP.dll

  Can someone help me?
  Once I start, I get a message that says: error loading C;\users\Toshiba\appData\Local\SMBDP.dll, then the module is not found.
  I tried everything but can't get rid of it,

  I asked for help online, but he told me to buy a tune-up utilities, but I already have untilities tune-up and have run through completely but it always does'nt work.

  Help, please.

  Hello

  TO be honest, this file is unknown to me. I searched using Google, but I couldn't find anything :(

  You can try a system restore to an earlier point or what have you done since you got this error message?