My pc will not boot mode "Eve". black screen, reboot reboot safe mode then anouther and all is well.

Similar Questions

• Laptop black screens after the latest updates of windows... wil not booting in SafeMode (black screen).

  Windows Vista 64-bit... Black laptop after the latest updates... windows screens will not boot into SafeMode again black screens.

  Hello

  I would suggest trying the following methods and check if it helps.

  
  Method 1:

  Try the steps in the following Microsoft article and check if it helps.

  Windows Vista or Windows 7 unbootable, and the Startup Repair tool does not resolve the problem:

  http://support.Microsoft.com/kb/934540

  Method 2:
  You can refer to the link below and check the drive for errors:
  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Warning: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.

  If the methods mentioned above do not solve the problem, then it would be best to contact the manufacturer of the computer.

  For more information, see the following Microsoft article and check if that helps.

  
  Why my screen is black when I start Windows 7? (Applies to Windows vista)

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: back up the registry in Windows Vista

• Memory will not work Diagnostic tool - black screen

  Hello

  I'm having a problem with my (relatively) new - an ASUS laptop UX - 21F. It worked very well for the first three months, but only in the last week has crashed several times on me with a BSOD. Unfortunately, Windows (Win7 Ultimate) does not create the memory dump file as it is currently specified to do so. (Yes, I checked, double-checked and rechecked re this parameter.) It simply does not create the image file.) Looking back through the event log, it does not match what is happening just before failure. It seems to be random.
  It sounded like a potential RAM for me, so I thought I'd run the Windows Memory Diagnostic tool. I chose restart immediately and... nothing. It restarts, messages and then it is a black screen and high enough system fan wind rising and the system gets hot enough. There is no cursor, or anything like that, and the only thing we can do is to hit the power button (it instantly stops, rather than having to four seconds). When it restarts, the system boots normally into windows.
  I tried to access the tool in many different ways and there seems to be no way to enforce. Each way I just get a black screen and a hot computer.
  What should I do here? I do a lot of development on this machine and I'm kind of falling ill to endorse things up to four times a day in case it crashes and I lose my job. Should I reinstall the OS and see if the problems go away? Or is there something less invasive than I do?

  Download and create the CD to boot from here:

  Memtest86 + http://www.memtest.org/

  If you have more than one piece of RAM in it, blow an and boot from the CD. If there are no errors, swap out with another room and boot on the CD again.

  Look in the event log at the time of the accident and see what are the entries for error there. This might give you a clue as to what is happening.

  Is the ' (relatively) new laptop "still under warranty by any chance? If so, you should also contact ASUS or the place you bought it from.

  SC Tom

• Son of anarchy BD Discs will not play on BDX4400 (black screen)

  Hello world!
  Just wondering if anyone can help with the following: I had some problems with the blu - Ray of the BDX4400 player (remote works do not, the reaction is slow, frozen Portal etc.) for awhile, but it was ok with playing DVDs / blu - ray... Up to our days. I come from the Sons of Anarchy box, insert the first disk, and then the screen goes black.

  You can hear the disc turning for a few seconds and the play icon appears but then it's all... Just a black screen and you can't even eject the disc (remote not working do not when it is at this point).
  I tried other discs of this set, but the same thing happens. However, the other DVD / Blu - Ray work. Therefore, I am sure that the player is fine, but maybe im missing a parameter that must be changed...?
  Someone had a similar problem? (I disabled the internet connections and the bd-live function, but not luck)

  The region code is correct and FW is up to date, so this may not be the root of the problem, if all fails, I may have to blame the actual discs, but I have trouble believing that 15 discs are damaged...

  Anyway, if anyone has any suggestions, which would be greatly appreciated.

  Thanks in advance

  It is always a stupid situation if everything works perfectly, but not with some discs/disc.
  In case your player works well with the other BR disks that the problem must be with the disks you have.

  Is there a possibility to test the disks on a few other BDplayer?
  You laptop / PC with BD optical drive? Can test you?

  To be honest, what is unclear to me that something can be changed (settings) in this case. Either it works or not.

• Windows 8 will not start, shows a black screen with cursor

  I tried to turn on my hybrid 3 cell / tab lenovo black this morning. After starting, it shows only a black screen with the cursor mouse mobile, but it stays like that for hours, until now. I can't turn it off, nor can I force turn it off by unplugging the battery it has unified the design of the body. What can I do?

  Hello Mel.

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver.

  I suggest you use the steps in this article and check if it helps.
  Reference:
  How to solve a problem of black screen crash
  https://support.Lenovo.com/in/Hi/documents/ht079944
  (Also valid for Windows 8)

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• PC will not boot past the home screen with USB HDD connected?

  Please read the entire post before suggesting a solution.

  Mobo: ASUS P8Z68-V LX, on the latest version of the BIOS.  Eight USB 2.0 ports, two USB 3.0 ports.  Intel i5 CPU. 8 GB of DDR3 RAM. Graphics card is NVIDIA GTS 8800 512, and I have a GTX 960 FTW on the way. Corsair CSX500 PSU.

  Model reader problem: WDBHML0040HAL-RK

  -J' ordered this drive of Studio 4 to WD outside of eBay for $109, used. The drive has been used previously on OS X, and I had planned to use it between two Windows 7, 10 and 10 OS X via dual-boot.
  -Boots PC regularly without the connected reader, but it hangs at the splash screen, if the player is connected to one of my 10 USB ports.
  -I can't not to enter the BIOS with the drive connected, and if I get into the BIOS without connection, BIOS freezes as soon as I make it connect.
  -I went into the BIOS, (with the device / disconnected /), and external hard drives moved to the low boot priority. This had no effect.
  -The PC recognises the drive if it is connected / after start. I can copy files to and from the disk without flaw.
  -When it is received, the disk has been formatted with a face-to-face 200 MB EFI system partition, (I have no background knowledge about it), with the rest ~3.5TB unscathed HFS + space.
  -Immediately, I formatted the partition HFS + and it separated in exFAT and NTFS.
  -Deletion of the EFI partition to command line has no effect.

  Someone online says that this is due to the ASUS P8Z68 trying to boot from the drive and to disable "Legacy USB Support" from the BIOS, but my knowledge of the ways all USB devices are disabled, including keyboards. I am doing a FULL disk formatting and will update the post I have try these solutions.

  I'm really in a bind here, guys. In all, any help is appreciated.

  Solved myself. I went back to the basics:

  The drive is 4 TB and I'm trying to use it as exFAT, for compatibility purposes. exFAT supports up to 2 TB per partition. The solutions are either break the 4 TB drive halfway, or to use the NTFS system.

  For the record, I chose exFAT.

  Marking this question.

• Vista will not boot

  Since auto-updates 2nd week of February 2010, my PC will not boot.

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  And read this update problems:

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Understanding Windows Update and Extras in Windows Vista at the link above.

   

  Remove the Vista updates; two ways to do this:

  1. a System Restore to before the updates:

  Click Start > programs > Accessories > system tools > System Restore > restore time/choose your own date > next

  If you use Norton, disable it before using the system restore.

  If it is impossible to enter the Normal Mode, do a Safe Mode system restore:

  Press F8 at the startup/power and the list of startup options, use THE ARROW key to select Safe mode > and then press ENTER.

  System restore steps according to the info above.

  Also:

  2. click on start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

  > then click the one that you don't want > uninstall will appear at the top > uninstall it.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

  > Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

  When you take a look at pending updates, you can either download/install them one at the time, namely the update causing you problems.

  > or if you do not need an individual > right-click on > UAC prompt > hide it

  See you soon.

  Mick Murphy - Microsoft partner

• Can't reinstall Vista. Because Vista will not get to the Setup screen.

  Hi people. Got a prob a little. Vista stopped booting the other night. So, I tried safe mode, and it hung on crcdisk.sys. So, I decided to get in shape. Problem is, it will boot from the DVD, but will not load / access the Setup screen (I waited for 7-8 minutes and nothing's happened, shows just the thing with the green bar).

  Not too sure if it's because the hard drive is 1 TB (but Vista was on the same front hdd with Windows 7). I tried to remove the 2 GB of ram (I use 4). No go. Tried another DVD rom, not go. Removed USB devices that have been connected. No go. I know that the DVD itself is fine. I tried on the other PC here, the installation screen came within 2-3 minutes. But his is not a 1 to (its 250 GB) the only DVD that will work / I install is the Windows 7 DVD.  So, how can I reinstall Vista?

  I deleted all partitions / recreated with the Win7 installation as well. Still couldn't get Vista to get to the Setup screen

  Any info appreciated

  Thank you

  Finally fixed it. I read that USB legacy can also cause this. So, I disabled it. Everything is good. Managed to get to the Setup screen, then reinstall Vista

• Sleep mode will not work after sleep said she sleeps for 2 seconds then the computer boots back on its own.

  Original title: "sleep" mode

  Sleep mode will not work after sleep said she sleeps for 2 seconds then the computer boots back on its own

  Hello

  See if this information helps you, Vista and 7 work the same:

  "How to restore the default power Plan settings in Vista"

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  "How to solve a problem of Mode Vista or Windows 7 sleep"

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  See you soon.

• When I try to start my laptop, it goes to the Acer logo screen and will not boot Windows 8.

  Acer E5-471

  When I try to start my laptop, it goes to the Acer logo screen and will not boot Windows 8. Only a black screen and mouse pointer appear. How can I solve this problem?

  Hello

  1 power off the device
  2. power on and immediately keep taping Alt + F10, unit will start to recovery, choose Exit & continue to windows. Post back if I helped

• VAIO will not boot xp. Crashes with blue screen error.

  VAIO will not boot xp.

  Sony Vaio PCG - 691L
  XP, installed at the factory has SP3 update.

  .5gig ram

  I worked on the machine to get to start XP. Sometimes it will boot in Safe Mode, but most of the time (and when it does not start in 'normal' mode), it crashes with a blue screen. The blue screen flashes fast to read, and then the machine tries to restart.
  Once I do start safe mode and got WIndows update but can't update due to the update that needs to be in normal mode.
  I was able to install Malwarebytes and a full scan. Also installed Spybot S & D and performed a full scan.

  When it does not start in normal mode it is slow, very slow. I tried rkill and it causes the machine down.

  It starts in normal mode today, but it crashed before I can get open IE and go to the windows update.

  Help...

  Thank you

  Rick

  Tired of playing with this. Re-install xp.

  Thank you...

• I received an update on your part 10/11/10 and now my laptop will not boot in place! I need HELP.

  I received an update on your part 10/11/10 and now my laptop will not boot in place!  I need help.

  Hi bobbymh,

  -Do you happen to remember the update has been installed?

  -You receive an error message when you try to start the computer?

  Follow the steps below:

  Method 1:

   

  Try to start the computer using the last good known Configuration and check if you can successfully start.

   

  For instructions, see How to start your computer by using last good Configuration known as Windows XP .

  Method 2:

  Perform the system restore from SafeMode to a restore point prior to the show and check if this solves the problem.

  See to run the system in safe mode restore

  See also How to restore Windows XP to a previous state

  Method 3:

   

  Follow the steps listed in the following article:

  How to fix a computer that does not start

  Gokul - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Windows Vista update (April 1, 2011) now the computer will not boot.

  1. Windows Vista update (April 1, 2011) now the computer will not boot.  Love updates been invited but now computer does not start. Just gets up to a certain point, and then restarts. Impossible to start safe mode! Don't know what to do, please help!

  Hi Ema1976,

  Do you have an error message when you try to start?

  Step 1: Disable the automatic restart of the menu advanced startup options and then enter the error message, see the link below:

  Advanced-Startup-options-including-safe-mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: Follow the steps mentioned in the link below to access system recoverytools and run the Startup Repair tool again.

  How to access the System Recovery Options menu?

  Run the tool to restart system as shown in the link below
  How to use Startup Repair?

   

• Cloning hard drive with Clonezilla failed, gave a bad sector error message and now the original hard drive will not boot

  Original title: startup problem

  I tried cloning from my hard drive with Clonezilla, and he gave me a bad sector error.  I have since run the hard drive test in bios and it passed.  Anyway, clone has failed, and now the original hard drive will not boot.  My dvd player won't turn when I try to load the Vista repair CD (Vista Home Premium 32 bit).  Clonezilla removes the start settings for the original disc?  And if so, how can I restore it?  The computer starts just a black screen with a cursor at the top left.  When I install the hard drive in a box and connect it to another computer, it shows the partitions and files all seem to be there.

  Hi DougEisenmann,

  Clonezilla is not supported by Microsoft.

  If you are unable to boot from the Vista repair disk then you will need to go into the system BIOS and make sure that it is configured to boot from the DVD drive.

  Check out the link:

  Windows to boot from a CD or DVD

  http://Windows.Microsoft.com/en-us/Windows-Vista/Start-Windows-from-a-CD-or-DVD

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions

  Important: Change the BIOS (Basic input output system) / Semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  See also the thread which has some troubleshooting steps for this same issue.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/Windows-Vista-crashedstartup-repair-wont-launch/49315171-1601-49DD-84fe-50bebd9ddbae

  The above link contains third party links provided by other users.

  Note: The use of third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer

• Network card not working plus-nouveau that bought now PC will not boot!

  Hello

  Mounted LAN realtek network card gave up the ghost so I bought this pci-e card on ebay.

  I installed it in each of the 3 slots of alternative but the PC will not boot with it in.

  This card is not compatible, or do I have to buy something else?

  Desktop HP Pavilion HPE h8-1070uk

  12 gig Ram

  Yes, exactly.

  Here is a link to many others...

  http://www.Newegg.com/product/ProductList.aspx?submit=Ene & DEPA = 0 & Order = BESTMATCH & N = 100006519 & isNodeId = 1 & Description = USB + RJ - 45 + Network + adapt & x = 0 & y = 0

  I would like to know well why these PCIe NIC cards cause the PC does not start.

  People install PCIe firewire cards, cards network wireless, sound cards and all work fine, but .they wired NETWORK card doesn't seem to work.  Not every PC is but several.

  A lot of confusion.