My sansa e260 suddenly is energized when I press the power button. Help please

Similar Questions

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• My his laptop makes a beep when I press the power button / stop and it does not start

  Hello

  I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

  -Mayur gala

  Hi Mayur,

  Welcome to the community,

  Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

  See the table below which shows the beep codes and the possible problem:

  Overview of beep Code
  Beeps	Description	Possible cause
  1	ROM BIOS checksum failure	The map system, covers BIOS corruption or errors ROM failure
  2	No memory (RAM) detected	Memory or memory slot failure
  3	Chipset error (North and South Bridge error) Time-Of-Day Clock test failure Gate A20 failure Super i/o chip failure Keyboard controller failure	System board failure
  4	Memory read / write failure	Memory failure
  5	Real Time Clock (RTC) power failure	CMOS battery failure
  6	Video BIOS	Video/smart card failure
  7	Failure of the CPU	Processor failure
  8	LCD SCREEN	Failure of the LCD

  Let me know if you need assistance.

  Thank you

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• Tecra A4 does not light when you press the power button

  When I press the power on button it turns green for 4/5 seconds then turns off.
  "I do all the tests the support on the page:
  
  * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

  * Connect the adapter to the computer.

  * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

  * Plug the power adapter into a different plug.

  * The battery, ensure that there are enough energy to start the computer.

  * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

  * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

  * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

  * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
  In vain:]

  You know? THX

  Hello

  There must be a hardware malfunction.
  You have tested a lot and nothing has worked
  I think there is not much to do, you all tired and I guess the authorized service provider could help you

  If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

• PowerEdge T410 won't do anything when you press the power button / stop.

  My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

  -Who-

  I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

  Problem solved

• HP DV6 6115TX UP STARTS NOT WHEN I PRESS THE POWER BUTTON / STOP NOTING HAPPENS

  LAPTOP: HP DV6 6115TX

  1. WITH THE BATTERY AND CONNECTED AC-

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  2. WITH THE BATTERY ONLY

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  Hello @HPDV6-6115TX ,.

  Welcome to the HP Forums!

  I understand that you laptop is not turning on.

  If the laptop has no power, other than the AC adapter connection indication, there is little that can be done.

  The adapter ring is HQ shows a white LED would suggest the adapter supply fine and offer pay-per-view mother, or at least the internal power connector. This means it is a flaw in the motherboard of the laptop and most likely requires a repair.

  You will want to check that the RAM and HARD drive are in place and connected, as well as internal power cable. You can do it by following your product Maintenance & Service Guide.

  HARD drive: Page 62.

  RAM: Page 66.

  Power cable: Page 83.

  If it does not, you will need to contact the HP support by phone for service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.

  Hope this helps!

• When I press the power button on my computer, it will beep but never displays the image on the monitor.

  original title: my windows vista only make a bep but not star of the monitor

  When the tray to start my computer to only a bep bep

  Hello

  beeps normally indicate a hardware problem

  read below to find out what your

  http://www.computerhope.com/beep.htm

  http://www.pchell.com/hardware/beepcodes.shtml

  If you can't fix it contact the manufacturer if under warranty

  If it is under warranty, contact a local reputable computer repair workshop

• Satellite L20 - Orange LED flashes when I press the power button

  For 6 - 7 times and nothing happens after that, the battery is completely dead and the adapter works fine

  I measured the voltage on the map that powers the battery and found 3.33v on 2 of them, the third is 0 v and the last of them starts by 0 v and goes up to 10v and more

  Hello

  Strange, but it might be a hardware malfunction.
  But first, you should try to remove the battery and the AC adapter. Attendre wait up to an hour, then reconnect the two devices.

  If it doesn t work it could be a motherboard problem or something else. I recommend you contact a technician for laptop.

• IPhoto crashes when you press the info button

  Since very recently, IPhoto crashes every time when I press the info button to enter people information a photo. I have version 9.4.3. running on OSX version 10.8.5. I added the first lines of pages and the pages or error report, if that can help anyone. I tried to repair the basis data, but without success. I am very grateful for any advice on this issue.

  Process: iPhoto [552]

  Path: /Applications/iPhoto.app/Contents/MacOS/iPhoto

  ID: com.apple.iPhoto

  Version: 9.4.3 (9.4.3)

  Generation information: iPhotoProject-720091000000000 ~ 1

  App item ID: 408981381

  The external application ID: 15017489

  Code type: X 86 (native)

  Parent process: launchd [139]

  User ID: 501

  Date/time: 19:50:47.475 2016-01-04 + 0100

  OS version: Mac OS X 10.8.5 (12F2560)

  Report Version: 10

  Interval since last report: 34492 sec

  Crashes since last report: 3

  Per-App interval since last report: 905 sec

  Per-App crashes since last report: 3

  Anonymous UUID: 23235B01-625D-2A47-6A8F-352C3092B10A

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0x00000000c53b6a10

  If you use iPhoto 9.4.5 or an earlier version, iPhoto will crash whenever you try to use maps. It is no longer supported.

  See:

  The first versions of iPhoto 11 started to plant for many users suddenly last month.

  There is a problem with the functionality of the site, because Google maps will no longer be supported.

  See the solution of Huxly647:

  Huxly647 , November 20, 2015 12:05 AM
  Re: iPhoto crashes after opening several times in reply to carvermon Useful

  I found a solution that works for me...

  1 goto /Applications/iPhoto.app/Contents/Resources

  2 delete the files 'googlemap.html' and googlesearch.html

  IPhoto no longer crashes, site does not work, but it doesn't bother me too much.

  Let me know if it works for you guys...

  Deletes two files "googlemap.html" and the googlesearch.html of iPhoto application bundle prevents the JavaScript running inside and causing the accident.  Log of course do the same thing. So it's pretty clear that something happened at the end of Google.

  To access the files inside the iPhoto application select it in the Finder and ctrl-click on it. Then use the command "Show Package Contents" from the menu.  Open the content subfolder and then resources.

  Do not try this fix without making a copy of the iPhoto application before trying to delete the two files of the entire application.

• Firefox crashes when I pressed the Browse button to upload files

  Windows 7 x 32 Firefox 10.02 the program crashes constantly when I press the Browse button (such as gmail attachments, virustotal programs and so on.)
  PS I've already eliminated the registry problems and attempted to delete MRU registry, such as mentioned in this topic: https://support.mozilla.org/ru/questions/754368#answer-105628

  Cor - el will no doubt come with suggestions. I will list the accident report Details incase they help someone. The accident occurred when a component associated Windows is in use. Have you ensured you have no background task running, and no unnecessary plugins Firefox are running.

  No reason to expect to be directly related, but a previous incident with the same signature took place when bookmarks were used, and the solution in this instance was:

  I found out that an option in Microsoft File Explorer caused the crash.
  To solve this:
  - Go to "Organize"
  - Choose "Folder and search options"
  - uncheck "Automatically expand to current folder"
  

   Now Firefox won't crash again!
  

  Your reports for s CrashID all have the same signature

  • related bug650664 - crash if I backup my favorites...
  • Signature: TV_GetItemRect (_TREE *, _TREEITEM *, tagRECT *, unsigned int)
    • 5d52e578-0069-4610-8efc-104252120219
    • f308eb2b-cbfe-40fd-81B5-d192a2120219
    • 6a538dc8-90ca-4B55-a662-5b7882120219
    • bff2939f-ac32-49D4-853C-622bf2120219
    • 0841e4b8-c464-4C84-91fa-3c9a62120219
    • 300aa7b7-b3da-4a20-85fb-9203a2120219
    • 4db23c0e-d90c-4701-b0a2-cbb192120219
    • 28f39d21-e4a1-4A37-8b20-d3a622120219

• ElliteBook 8460p will not be running when you press the Start button

  Hi Ant classmates.
  
  I am facing a problem with my 8460p ElliteBook. When I press the Start button it won't start and I need to apply some mechanical vibrarions so he reacts to the button. I guess that there is a problem with a connection inside. The thing is that he does not always fail, but it happens more often. I'm afraid to send it to HP support and resume with a message like "the problem didn't see the - up." I'm close to the date limit of warranty, but I need my laptop for 3 more weeks for professional issues. What should I do?
  
  Thank you

  Hello Angelica,.
  Welcome to the HP Forums.
  
  I'm sorry, but to get your question more exposure, I suggest posting in the trade forums, since it is a commercial product. You can click here for the link.
  http://h30499.www3.HP.com/hpeb/
  
  Thanks for posting on the HP Forums.

• Hi, actually I want the program stops when you press the stop button. but the problem is the program is runing in loop only he doesn't return tile view deleted complete execution of any body can help me for this.

  Hi, actually I want the program stops when you press the stop button. but the problem is the program is runing in loop only he doesn't return tile view deleted complete execution of any body can help me for this.

  Here

• My cd-writer/DVD disc tray does not open when I press the Open button. He is not blocked and has no disk in it. How can I me t to operate?

  Cd-writer/DVD disc tray does not open when you press the Open button, or when you use the buttons to control the media on the keyboard. How can I restore it to its operating state?

  Hi John,.

  Please let me know exactly what happened when you tried my suggestions of first and second.

  Of your most recent post, looks like you're watching the wrong part of the Device Manager. Optical drive is listed under "readers of CD-ROM/DVD-ROM". The info you gave appear under "drives". If the drive is not listed under "readers of CD-ROM/DVD-ROM" or there is no such section in Device Manager, then Windows do not see. If windows can't see it then this means that there is no power or that the drive is broken.

  When you pushed the drive back in, the player no longer has much of the book or did you have to push all the way. If the latter, it means that the drive has no power or is broken.

  With respect to the opening of the case, I guess I should ask first if it's a laptop or desktop?

  Tricky