My system hangs during startup "for the first time" after running the system recovery.

HP G62 - 227 CL

Win 7 (64 bit)

No error message, in itself; just a screen frozen on reboot.

Months, my computer has suddenly started glitching on me.  I stopped and tried a reboot.  The system froze on start with flying colors.  System recovery tried several times but must have made a mistake because he wouldn't.  Resolved to buy a new hard drive and reinstall from the recovery disks.  Delayed unnecessarily until today, months later.

Before you buy a new hard drive, has decided to relaunch the system recovery.  It worked!  I tried the option that has deleted everything and restored to the software and factory settings.  Everything seemed to work like a charm: hard drive reformatted, reinstalled software, the system prompted me to reboot.  Yes, I did.  Windows started to boot, "Preparting your computer for first use of Setup" appears... and freezes.  For hours.  Hard drive led is off.

BTW, made sure the button Wi - Fi was on what I read on the problems of recovery if it was turned off when the program is run.

Restarted.  Press F11.  A ran maintenance and checked the hard disk for errors.  There are errors.  Unfortunately, the default setting of CHKDSK does not repair them.   A opted for a command line.  RAND CHKDSK again with option '/ f/r' seen in other posts.  Here I am too ignorant to get the program to run properly, I guess.  I ran CHKDSK on the two player X and C.  No error found... sort of.  I know they exist because the system will not start.  (Yes, I tried again.)  Return to the command prompt, I tried to run CHKDSK on the drive C again.  This time I got a message that I must first dismount (remove?) the reader.  As I don't know what that means, I opted for the 'no' and have decided to post this help message.

So.  Suggestions on what do I do then?  More specifically: How do CHKDSK to fix the errors it found?  I think the message was: "errors in $130 of the sector...". "It shows this message two times at the end of 62%.  Freezes for a long time.  Gets will still only slow down to a crawl again around 70%, but no longer.  Then returns to the start of system recovery screen.

System recovery ran again for the pleasure.  Again, seemed to work like a charm.  Unfortunately, the laptop again sits frozen at "Preparing... for first use" screen again.  It heats more turns.  The audible fan works now plans higher... If none of this helps.  I am stopping and waiting for your advice.

Thank you!

Zac:

My apologies for the delay to return to you.  Believe you that computer gremlins have not hit my very stable desktop which has been fine for years with sudden instability driver?  McAfee thanks for this most recent update!

In any case, after several diagnoses and find the hard drive has failed in each of them, I decided to install a new copy of Windows 7 as a test while I wait for my upcoming recovery disks in the mail.  I did it by removing all partitions on the drive and do a fresh install.  Here again, everything seemed to go well until that (apparently) a certain area of the drive was used to save/installation of the files.  Even after CHKDSK runs several times (each time he repaired several defective sectors but stalled after only 10% of the disk) the system will become unstable - the last number being a blank screen after logging on to Windows.  So, all in all, epic fail on the side of the hard drive.  The new drive is installed and waiting for my recovery disks.

Thanks for all your suggestions.  They have been a great help with information, but not with the results because of the training.

M

Tags: Notebooks

Similar Questions

  • (Redirected) Dell audio drivers will not load when the system is turned on for the first time after his stop.

    Dell audio drivers will not load when the system is turned on for the first time after adoption of Windows 10. I have to reboot every time. So what I'm doing puts the system into sleep. in this way, I don't need to stop and restart the system. It is Dell Inspiron N5559. Audio drivers are installed and up-to-date. Equipment works correctly.

    Hi akilesh.sharma18,

    Please repost this in the Audio forum from the laptop to help.

    http://en.community.Dell.com/support-forums/laptop/f/3517

  • XP hangs before logon for the user profile.

    Propely at startup of Windows, but XP hangs before logon for the user profile.

    The system does not start in all modes like without failure, command prompt mode, last know good Configuration. But it starts only in XP system recovery mode.

    What happened after cloning of a XP C: hard drive Sata Drive Dell OptiLex 760 to another System DELL OptiLlex 760 . I've used Norton Ghost 15.

    Hi ANM

    · Have you created an image of the system using Norton ghost backup software?

    When you create system images using backup software, it is supposed to ideally be used on the same computer, since you cloned it on another computer, it seems to me that the user profile is corrupted and failed to load.

    If the problem is the DELL OptiLex 760 system then I suggest you to connect with Norton Ghost.

    If not then you can follow the market from the link below: how to recover from a corrupted registry that prevents Windows XP startup: http://support.microsoft.com/kb/307545

    With regard to:

    Samhrutha G S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Slow to open the first time after startup apps

    Slow to open the first time after startup apps

    How about, the second time, that is, close and reopen?

    Also download and run Etrecheck.  Copy and paste the results in your response. Etrecheck is a diagnostic tool that has been developed by one of the most respected users here (and recommended by Apple's Support personnel) of the CSA to provide a snapshot of the system and help identify the most obvious culprits that can adversely affect the performance of a Mac.

  • Firefox crashes while loading images for the first time after windows starts upward

    every time I log on windows, Open firefox and load an image or a site with content firefox flash stops responding for 2 or 3 seconds and then returns to normal after that and everything is fine... it happens only when I open firefox for the first time after starting windows to the top...
    thing I tried
    Start windows and Open firefox in safe mode (does'nt fix the problem)

    updated 13 solved the problem...!

  • What is the best product for a first time user of WORD PRESS to design a web page of writing-blogging?

    What is the best Acrobat product for a first time web page or blog page - very technical designer - to design a place to show the writing and blogging information?

    You can use these options for WP blog in Muse:

    http://musewidgets.com/search?q=WordPress

    Thank you

    Sanjit

  • get the error "no sequence valid is not found for the set of patches" msg trying to launch Acrobat XI for the first time after installing - suggestions?

    get the error "no sequence valid is not found for the set of patches" msg trying to launch Acrobat XI for the first time after installing - suggestions?  Using Windows XP.

    Hi James,

    Let me know if the problem persists.

    Kind regards

    Nicos

  • Transitions is messed up the first time it runs

    In the following code when the need to register the button is pressed the transitions is wrong the first time it runs

    <? XML version = "1.0"? >
    <!-transitions\LoginFormTransition.mxml->
    " < = xmlns:fx s:Application ' http://ns.Adobe.com/MXML/2009 "
    xmlns:MX = "library://ns.adobe.com/flex/mx".
    xmlns:s = "library://ns.adobe.com/flex/spark" >

    <!-Application of the property of the class States sets the display States.-->
    < s: states >
    < name s: State = "default" / >
    < name s: State = "Save" / >
    < / s: states >

    <!-define the transition to animate the view state change. ->
    < s:transitions >
    < s:Transition fromState = "default" >
    < s:Parallel >
    < mx:Resize target duration = "{loginPanel}" = "500" / >
    < s:Wipe can feel = 'right' target = "{confirm}" / >
    < / s:Parallel >
    < / s:Transition >
    < s:Transition fromState = 'Registration' >
    < s:Sequence >
    < mx:Resize target duration = "{loginPanel}" = "100" / >
    < / s:Sequence >
    < / s:Transition >
    < / s:transitions >

    <!--> set the Panel container title based on the view state.
    < s:Panel id = "loginPanel".
    title = title of "Login". Register 'Registration' = >
    < s:layout >
    < s:VerticalLayout / >
    < / s:layout >
    < mx:Form id = "loginForm" >
    < mx:FormItem label = "username:" >
    < s:TextInput / >
    < / mx:FormItem >
    < mx:FormItem label = "password:" >
    < s:TextInput / >
    < / mx:FormItem >
    <!-add a TextInput control to the form to register view state. ->
    < mx:FormItem id = "confirmation" label = "" confirm: "includeIn ="Save">"
    < s:TextInput id = "Myti(nose)" / >
    < / mx:FormItem >
    < mx:FormItem direction = "horizontal" >
    <!--> use of the LinkButton to the register view state.
    <! - exclude the LinkButton to the register view state. - >

    <!-add a LinkButton to the shape of the State of registry view. ->
    < mx:LinkButton label = "Return to Login.
    includeIn = "Save."
    a click = "currentState =" "/ >
    < mx:Spacer width = "100%" id = "spacer1" / >
    <!--> SETTING label of the control based on the view state.
    < mx:LinkButton id = "registerLink".
    includeIn = "default".
    label = "Need to register?"
    a click = "currentState = 'Register'" / >
    < s:Button id = "loginButton".
    label = "Login" label. Register = "Save" / >
    < / mx:FormItem >
    < / mx:Form >
    < / s:Panel >
    < / s:Application >

    Looks like this could be the bug: http://bugs.adobe.com/jira/browse/SDK-28787

  • The computer hangs during startup until after latest upgrade of Windows 7

    My new Dell has a little less than 3 months and so far has worked like a dream. It runs Windows 7. The latest Windows updates, which there were 3 were installed as I stopped last night. When I booted the pc this morning he hooked up with the following message: "Operation Applying 51 51 (\Registry\Machine\Components\...) update".

    The pc reacts more than anything, so finally, I manually turned off and restarted. The system returns to a previous Restore Point. Later in the day, I turned off the pc how he downloaded 3 updates (probably the same ones again) and the same problem occurred when restarting later. The pc is running McAfee SecurityCenter, which has been pre-installed again.

    Please can anyone help with advice for this problem?  Thank you.

    Peter

    Consider yourself lucky.

    Because this update was 'critical', he went ahead and downloaded itself last night while I was asleep.

    I woke up this morning to a glorious flashing cursor whenever I try to start.  My computer still runs beautifully, now it does not even start.

    Thank God for this update, otherwise I might be able to get for the photoshops I was working on that.

    Before restoring personal windows comes to talk here about starting of system restore and all the other _ with windows that never worked for me once, I already tried it.

  • Computer hangs at startup of the system

    Original title: computer crashed win Defrag

    I recently picked up win defrag... I have windows xp and tried to put it in safe mode, and it froze.  Now it is completely empty when I try to start :(  I removed my hardrive and crossed norton key usb connected to another computer.  It's still frozen... I'm on the right track?  How can I manually remove the infected files from another computer?  Please help-

    K

    Hi katkit,

    1 did you stop defragmentation on the drive?
    2. using Norton on another computer, were you able to remove the infected hard disk files?
    3. do you get an error at startup of the system?

    You are on the right track if your hard drive is infected with the virus. However if you try to do something else, then I think not that it is a good idea. After scanning of the hard drive, connect it to the computer problem and start insafe mode.

    Please provide us with more details, so that we can better help you.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • The DirectX Web Installer hangs during installation of the components

    I try to get several games running, but am stuck by the demands to DirectX 9 c. My machine is Windows 7, so it's DX11 installed. I went here to download the web installer:

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=2da43d38-DB71-4C1B-bc6a-9b6652cd92a3&displaylang=en

    When I run the installer, it downloads the components, then hangs on "Installation of components. It displays the message "copying files...". "and the 1.0.2910.0/Microsoft.DirectX.Direct3DX.xml

    One of my CPU is maxed out running dxwsetup.exe * 32 and this for hours. My computer is a Dell with Windows 7 64 bit.

    Are there instructions anywhere to update DirectX to hand?

    Thanks for any help.

    Steve, thanks for your suggestion. Running at startup using the minimum does not solve the problem, but it got me thinking in the right direction.

    I finally put in the Win7 disc and 'fix '. It is really a re - install, but the programs and data are stored.
    It took a few hours to go through the installation, but after that, I ran the DirectX Web Installer smoothly. Played some BioShock 2 last night!
    Thank you
  • HP Pavilion HPE h9-1100 Phoen: computer hangs during startup after installation of 970 GTX

    The problem:

    So here's the deal. I bought a new EVGA GTX 970 and installed in my office (after you have uninstalled the drivers for my old AMD GPU). When that I start it freezes on the BIOS screen. Press a button and the screen goes black; It is still frozen. Fan works in beast mode, until I turn it off.

    What I tried:

    • I checked for if sure it was well installed in the x 16 PCIE slot and connectors double checked.
    • Checked to see if my motherboard supports UEFI (it does)
    • Using another monitor using vga instead of as before display port.
    • EVGA called and suggested they updated my BIOS on HP site (I think I'm already on the latest version)?
    • Called HP and they said I have spend $250 to have a technician to work on it. (I'd rather not pay nearly as much as I paid for the card to install it if I can avoid...)
    • Remove the battery on the motherboard for 5 minutes then replace and powered with the new graphics card.

    None of these things had No effect. (with the exception of the money payer which I have not yet made). I put the old card (Radeon 7670) back in and it started late.

    I'm kind of grasping at straws at this point. Any help would be greatly appreciated.

    Model: h9-1100 (A5U16AV #ABA)

    OS: Windows 10 Pro (64-bit)

    Motherboard: Gigabyte 2AC8 (970 (RX980) + SB950 chipset AMD)

    Processor: AMD FX-8150 (3600,0 MHz)

    BIOS: Ang_716 (05/04/2012)

    I would like to know if there is relevant information, that I left out.

    -edit

    I tried to install the card in HP h9 1300 t friend (he also recently installed the same card) it worked fine, if the card is not defective. Then we installed his gtx 970 in my computer. Same results as before. Startup freezes on the bios screen.

    Sure that I narrowed down it to a compatibility problem with my motherboard. I ordered a new one, the ASRock 970 M Pro3 AM3 + / AM3 AMD 970 + AMD SB950 6 x SATA 6 Gb/s USB 3.0 Micro ATX AMD Motherboard (bite). I'll post here once again with results once it arrives here in a few days. I cross my fingers.

    Hello

    The level of the BIOS of your PC is not compatible with the video BIOS in the NVIDIA GTX 970.   You need a BIOS to version 8 HP which is not displayed for your PC.

    BTW - A replacement of the card mother not HP will require a new license of Windows.

  • InDesign 2015 hangs during startup by starting trackers

    My indesign 2015 hangs when starting

    At each time with stalkers of departure

    tried removing software, reboot and software reinstalled, but nothing not working

    OK, that means it is a problem in the user profile files, probably the permissions on the folders preference for InDesign. You can try to replace the prefs (see replace your preferences), but most likely that will not work, then you must delete or rename the two hidden folders (the paths are in this link), then copy the two files from the user to work.

  • Can I get animation character to recognize my face in the preview window and put the REST POSE, but the character still doesn't move. Ideas for a first-timer?

    So, this is my first time using character Animator and I thought, why not start with the included Preview "Getting Started Project (excerpt 3)".

    So far, we see my image of the camera, and I could so he could follow my face by selecting "Set rest is" following the instructions. The red dots are moving with my face, but the character just sits there. I don't know what to do.

    ChAnim Screenshot01.png

    It seems that you have only selected Poof. Pouf is not a behavior of face (look to the right in the properties panel).

    A puppet must be selected before it recognizes head movements and other behaviors. Try selecting one of the puppets with face behavior.

  • Juice I bought and installed creative suite 5.5 Design Standard today (for thr first time) and could n

    I just bought and installed creative suite 5.5 Design Standard (Student and Teacher Edition) for the first time today.

    How can I can create PDFs directly with Acrobat?

    How can I change or edit the pdf downloaded files?

    I'm having trouble making the two basic above things. Can anyone? Thank you!

    Joy

    Thanks a lot for your detailed response and links.

    Frankly, I bought the program thinking I can easily create PDF with acrobat and also be able to modify PDF files with the program.  Your explanation above, it seems that these two simple functions are a major challenge. I'm a little disappointed. I will read the content of the links that are provided, but may I ask if there is a good program on the market that I could use to download a PDF file to edit it or save to PDF conversion front?

    My problem is that I often don't have access to the server where the file origin. So what can I do in this case?

    Thank you

Maybe you are looking for

  • iCloud Drive not sync on iOS 10

    Hello As I moved to Sierra and iOS 10, my iCloud reader app on my iPhone is not in harmony with what is on my Mac. All my documents are missing. They are on my Mac, on iCloud.com, but will not be displayed in the app iCloud on my iPhone that doesn't

  • 1telephone 4S lights after put 9.3.3 update

    I just uploaded my iPhone 4s to iOS 9.3.3 and now I can't turn on my iPhone. I restarted several times, but it still does not work. The Apple appears and it is stuck on the screen for a few minutes and then returns to the darkness. I tried everything

  • Replace the video cable Widescreen Y550 and stop random downs.

    I'm looking for opinions. I have a big screen of 3 year, Y550. The hinges are is detached and has finally folded the video cable a year ago, the battery is dead, and (perhaps because of the set video cable) it sometimes stops suddenly when the screen

  • Picked up my office and he said that my Windows Vista is already in use

    Diagnostic report (1.9.0027.0):-----------------------------------------Validation of Windows data-->Validation status: invalid licenseValidation code: 50Validation caching Code online: n/a, hr = 0x80004005Windows product key:Windows product key hash

  • How do you put the document on the Windows 7 Desktop iPad files?

    I recently bought an iPad 3 and would like to be able to download 'My Documents' (personal folders) of my Windows 7 desktop.  Anyone know how?