My t61 - no power after changing the power plug

Similar Questions

• error printhead after changing the printhead in L7680

  I have an OfficeJet Pro L7680 that is a few years old.  Recently, I have noticed a decline in the print quality for mainly black, but also a little yellow, and after changing the black cartridge with no changes, I decided to change the Black/Yellow Printhead.  So, I thought that if I'm trying to change a print head, I should change the other (cyan/magenta).  I bought new Office Depot print heads.  After replacing the print heads that I was able to print a page or two, and then all of a sudden the printer started saying there is a problem with the cyan/magenta printhead.  I tried to remove and reinstall, the suppression and power reset and then put it back up, etc, but nothing moves it.  I have not yet called HP, but I hope that when I do they will help because the print heads are under warranty until 2014, even if the printer is out of warranty.  In the meantime, I thought I would ask here is - it possible I only have a print head of DOA?  Or would it be the printer?  Unfortunately I threw the old printheads immediately (stupid me) so I can't try that goes back to the old magent/cyan print head and see what happens.

  Hello jmmarton.

  Your chip printheads were damaged by inserting wrong while the transport is always on the right side. This document provides instructions on how to replace the printhead to the unit.

  Use the link below to find how to contact HP phone support in your country.

  http://WWW8.HP.com/us/en/HP-information/summary/WW-contact-us.html

  See you soon!

• Speakers stopped working after changing the device sound card

  * Original title: switched to hi-speed of dial-up, speakers stopped working / / rev. #2 Can I change the title of: speakers stopped working after changing the device sound card

  I have a Motorola SM56 speakerphone modem, I went from dial-up to the Road Runner.   When I open Device Manager and expand the sound column it lists "High definition Audio Device" (manufacturer of Microsoft), there are 4 that say "NVIDIA High Definition Audio" then there is one that says "Unimodem Half-Duplex Audio Device.  When I open the properties of the Unimodem device it says ' device working properly. "

  Let me start at the top under "General".  It lists the name of the device: Unimodem half-duplex Audio device.    Device type: audio, video and game controllers;    Manufacturer: Microsoft;    Location: Motorola SM56 Speakerphone modem.

  My speakers worked very well before I went.   I tried updating the driver but he came back with "best driver already installed.  It is a desktop PC, it is about 6 years old, but has been revised, graphics card new, updated to power, new 4 GB ram I think.  The hard drive is 1 TB.   I'm running Windows 7 Pro.  I forgot to mention, if I open a WMV file and volume in the taskbar commands, I see the green light moving.  The green light on the actual speakers turned on, just no sound.  It seems to me that the old speakers do not like the new modem from Time Warner. (I'm an old lady, what the devil I know)

  It is a question of another driver, or is it something else?

  Any help would be greatly appreciated.

  Are plug you the speakers into the modem?

  They must be connected in making your computer speaker, usually a light green color (read the manual of the machine). Go to control panel / sounds / playback and make sure that the type of speakers you selected as the default device.
  Audio device drivers updated its better to not use MS Update (it is not). Re-post giving your machine make name and exact model number (for example HP, Inspiron, ABC1234 etc.).
  See you soon,.
  Jerry

• HARD does not work after changing the disk partitions recovery media creator

  Hello world

  After installing windoows 8.1 April major upgrade (win 8.1 presents as OEM), and have shrunk C partition to create a data partition "D", "Troubleshooting" option under advanced start menu is no longer available.

  Toshiba Recovery Media Creator does not work, too (it can not find any hard disk recovery partion).
  I got in the OEM recovery partition.
  I am also able to create a recovery using the Windows tool unit.
  You have no idea about it?

  Thank you very much!

  Hello

  Sorry to hear about all this. Unfortunately, you now have a big problem. I don't understand why you didn't create support of recovery before you started to change the factory settings, including to change the structure of the partitions of HARD drive.

  Mobile offered with factory settings a structure specific partitions and recovery recorded image is saved on the partition of drive specific and marked with invisible markers. These markers are visible for preinstalled Toshiba recovery media creator tool and when you start the tool can find points of reference and has full access to specific files.

  Unfortunately, after changing the original scores structure Toshiba tool cannot find these markers more and is not able to copy files from recovery media recovery. What you need now is the original recovery disk. Using this disk, you can install original recovery image and after doing this, you will have new factory settings.

  I know it sounds stupid now but you must order the original recovery disk and it can be done on https://backupmedia.toshiba.eu/landing.aspx

  If you have any other questions you are welcome.

• After changing the MagSafe adapter, macbook pro takes too long to start the video

  After changing the map of 85 W MagSafe, time to start the computer has become excessive (2 minutes). The screen lights up immediately, but the video appears after 2 Min.

  Once started, the performance of the computer are OK.

  This anomaly occurs after the change of the adapter, it's never happened before.

  Try a SMC reset:

  https://support.Apple.com/en-us/HT201295

  Ciao.

• Satellite 4080 Xcdt, small image after changing the resolution to 800 x 600

  Hello.
  After changing the resolution to 800 x 600 or less (while playing an older game BACK), the screen is reduced to the size of the postcard.
  Someone at - it an idea to solve this problem, (another driver display or s.th.)?

  Greetings, r.

  Hi Ralf,.

  In my view, there is a setting in the BIOS to force the screen image to stretch to fit the available space.

  Kind regards

• After changing the administrator password in windows server 2003, I can not connect the next day why?

  After changing the password in windows server 2003, when the new password take effect?

  Hello

  In dealing with the problem with Windows Server 2003, it would be preferable to send the same in the Technet community. http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  Hope the information is useful.

• Office Jet 6500 will not print after changing the ink cartridges

  Office Jet 6500 will not print after changing the ink cartridges

  Hello

  This doesn't seem to be a problem with the printer itself and not Windows. I also suggest to contact the manufacturer. In this case, HP.

  Please see here: http://www8.hp.com/us/en/support-drivers.html

• Photosmart 6520: 6520 Photosmart printer stopped printing black after changing the print cartridge

  There was a similar position two years ago. After changing the cartiridge (564XL) black printing, the printer will not copy documents. He behaves as if I placed a blank sheet of paper on the glass. I can scan the document and print the .jpeg, but not the document. The print quality of everything else is mediocre - very light on blacks, even though the colors are fine. I ran through all the diagnostic tests and he told me that the printer is fine, although the black box on the diagnostic page is empty. The difference between my printer and the one in the previous post, it's mine is 18 months and longer warranty. It has been little used. In the previous post, none of the solutions have been proposed, but apparently HP has replaced the printer. Any suggestions, or is this device intended for scrap?

  Try youtube videos here.

  https://www.YouTube.com/results?search_query=Photosmart+6520+print+head

  Looking to learn more.  If no joy, your printer is toast.

• HP laserjet p1006: does not print after changing the toner

  I just changed the toner. The green light is on, but when something I send to the printer to print, the orange error light. Before inserting the toner, I pulled the Strip in transparent plastic attached to an orange tongue and the black cloth. I tried to reinsert the toner and turn on/off the printer again. Help please if you can. Thank you!

  Hi @cindycb,

  Welcome to the Forums of HP Support! I read your post and to see that when you try to print after changing the toner, the Attention light. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Make sure all the orange, packaging material is to remove the toner.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Try and print a self-test on the printer hardware to see if it is a hardware or software problem.

  Open and close the cover five times quickly. It should print a page with black lines on it.

  You can find the flashing light distribution in this document and the right solutions for the reason that you are experiencing, lights blinking on HP LaserJet P1005, P1006, P1007, P1008 and P1009 Printer Series.

  You use Genuine HP Toner?

  Please let me know the result and if there is anything else I can help you. Thank you.

• HP2840 which has just started to squeek terribly after changing the drum.

  Can anyone help to maintain the HP2840 all in one color laserjet

  The squeeking started after changing the second image drum

  thketer,

  Self-satisfied, you got what it takes .

  Good luck!

• After changing the motherboard in my PC the device software windows 7 cann't be activated. I tried many times to speak with the service the customer but failed.

  After changing the motherboard in my PC the device software windows 7 cann't be activated. I tried many times to speak with customer service through automated phone system, but failed. Now what should I do.

  The OEM of Windows 7 versions are identical to the versions commercial full license with the following exception:

  -OEM versions don't offer any free direct support from Microsoft technical support Microsoft

  -OEM Licenses are tied to the computer first you install and activate it on

  -OEM versions allow all hardware upgrades except for an upgrade to a different model motherboard

  -OEM versions does not move directly from an older Windows operating system

  What is OEM software? :

  http://support.Microsoft.com/GP/oemsupport_1/en-GB

  Licensing FAQ:

  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_faq.aspx

  --------------------

  Windows 7 - version comparisons:

  http://Windows.Microsoft.com/en-us/Windows7/products/compare-editions

  MS Windows 7 store price:

  http://store.Microsoft.com/Microsoft/Windows-Windows-7/category/102

  --------------------------

• Internet connection is slow after changing the MAC address

  * Original title: win7... problems with internet after changing the WIRELESS card MAC address

  I have win7 home ed... .i tried to change my WIFI MAC address of the card (I had a reason to do so), SMAC program change but I could not, the address remained the same... I changed my mind... has decided to forget about this topic... but unfortunately, I had a big problem (very probably)... the internet connection is too slow or stop a few times pages load too slowly or especially do not charge. downloads are always stop in network on Chrome error... I tried a different browser to check, but the problem exists with all explorers, it's big terrible trouble please help me (Note: this problem is related to some how with internet traffic... late night speed is much better, but not 100%... but of course not as speed) ", I had before changing to MAC)... Thank you very much

  Hello

  1. what made you want to change the MAC address?

  2. what exactly happens while you are trying to connect to the internet?

  3. you receive an error code or error message? If Yes, what is the full error message?

  4 have you checked the issue in internet explore as well?

  Please follow the steps below and we update with the results.

  Method 1: Run the network troubleshooter, and check.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  Please try following the steps provided in the article and check out them.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  For more information, see the articles and check out them.

  10 tips to help improve your wireless network

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx#fBid=hq7zl63PiZ9

  Why is my Internet connection so slow?

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow

   

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps!

• Printer problem - after changing the cartridge, I get a message that the USB cable is not connected

  As above. I checked the USB port and it is connected.

  Original title: printer problem. After changing the cartridge, I get a message that the USB cable is not connected?

  Hello

  1. you receive an error message/code when you try to print?

  2. What is the serial number and model of the printer?
   
  Follow the steps.
   
  Method 1
  Run the hardware and devices Troubleshooter
  This utility checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Also run convenience store Print that would help us diagnose the problem better
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 2

  (a) check the physical connection of the printer and make sure that the USB cable is properly plugged.

  (b) connect the printer to a different USB port and check if it helps.

  (c) check the on another computer.

  Method 3

  Run the fix - it tool from the link.

  Diagnose and automatically fix problems printing and printer http://support.Microsoft.com/mats/printing_problems/

  Method 4
  If the previous step fails, follow the steps described in the following link:
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
   
   
  Let us know if it helps.

• After changing the port (1521 to 1525 in listener.ora and tnsnames.ora) OEM: the database is down

  Hello

  I'm installing Oracle Database 11 g 2 (11.2.0.4) on Oracle Linux 7.1.

  In short, what I'm trying to do now is changing the default port of 1521 to 1525.

  So I stopped the listener (lsnrctl stop) and then changed my listener.ora and tnsnames.ora:

  Listener.ora

  listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora

  # Generated by Oracle configuration tools.

  LISTENER =

  (DESCRIPTION_LIST =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))

  )

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1525))(HOST = localhost))

  )

  )

  ADR_BASE_LISTENER = / u01/app/oracle

  tnsnames.ora

  tnsnames.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/tnsnames.ora

  # Generated by Oracle configuration tools.

  BI =

  (DESCRIPTION =

  (ADDRESS_LIST =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1525))(HOST = localhost))

  )

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = bi)

  )

  )

  And then changed the local_listener:

  SQL > ALTER SYSTEM SET LOCAL_LISTENER = "(ADDRESS = (PROTOCOL = TCP)(HOST=localhost) (PORT = 1525))";

  SQL > ALTER the REGISTRY SYSTEM;

  Finally, I started the listener (lsnrctl start) again.

  Then I tried to connect using Oracle SQL Developer to the customer. The port of 1525 works perfectly well.

  The problem is, when I open the OEM (Oracle Enterprise Manager), it says: "the database is down. Please specify the credentials of the host to access the restart and database diagnostic tools," which is like this: http://imgur.com/oKLPW65

  So I logged on the account of the host, and it shows that the database instance, listener and the agent is all down like this: http://imgur.com/Bzr84bz

  It seems that the port used by the OEM is always 1521.

  What should I do? Can someone help me solve the problem?

  Thanks in advance.

  UPDATE:

  After changing the emoms.properties & the targets.xml (thanks to Elisabeth), you will need to reconfigure dbconsole using emca.

  So what I'm doing is decreasing the config:

  $ emca - deconfig dbcontrol db-rest drop

  and then create again:

  $ emca - create config dbcontrol db-rest

  Voila.

  Best regards

  Jerry Antonius

  Hello

  Try to change the port numbers in the following files

  Don't port no 1521 to 1525

  $ORACLE_HOME /_SID/sysman/config/emoms.properties

  oracle.sysman.eml.mntr.emdRepPort = 1525 (before 1521)

  $ORACLE_HOME /_SID/sysman/emd/targets.xml

  (Before 1521)

  (Before 1521)

• LiveCycle ES4. I am trying to move a picture online with a text box to create a header.  I had to create a subform that flows to generate multiple pages of text.  After changing the settings, it seems that I can't place images and text where

  LiveCycle ES4. I am trying to move a picture online with a text box to create a header.  I had to create a subform that flows to generate multiple pages of text.  After changing the settings, it seems that I can't place the images and the text I would like.  I tried moving them to the bottom, but does not work.  Is there a way to encapsulate the images so that they can be places as much as I want?

  Select your photo and text inside the subform flowed. Right-click and select wrap in subform do the positioned Subform subform. This will allow you to move objects in this subform positioned the way you like them.