myDAQ new installation self-test fails 88705

Similar Questions

• Pavilion p6330f PC: SMART Test: SMART short Self Test FAILED

  I had so many problems with this computer. Whenever I have turn it off then go turn back will go to Recovery Manager. I did run the computer health check and did the basic test and Test drive both hard say Test INTELLIGENT: SMART short Self Test FAILED. What does that mean?!

  Hello

  It simply means: the HARD drive is about to die. Please save all your data if you could and be prepared to replace the HARD drive. Is your machine still under warranty? If so, please contact HP for replacement

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Kind regards.

• Hardware diagnostics: "SMART short Self Test - failed" and "targeted read Test Failed.

  Original title: "SMART short Self Test - failed" and "targeted read Test Failed", all the patches?

  When using PC checkup of Dell I get the following errors; during the analysis of the material. "SMART short self-test - failed" and "targeted read Test Failed", all the patches?

  Hello Duane,

  Teke section of the Web site that speaks of similar problem.

  http://forums.techguy.org/hardware/906455-smart-short-self-test-fail.html

  The problem is with the hardware and you can get in touch with Dell computers.

• XPS12 SMART short self-test fail WHD16 LY6

  "When you run the Dell ' Checkup" utility on the SSD drive, the drive will fail with:

  SMART short self-test fails WHD16 LY6

  The remaining tests are ignored. The suggestion is to update the firmware. However, my drive is:

  LITEONIT LMT-256M6M 256GB mSATA

  and I can only find firmware on the Dell site for both LITEONIT SSD 256 GB drives, or precisely what mine are. (Only LITEONIT LCS-256M6S 2.5 256 GB and LITEONIT LMT-256M3M MSATA 256Go are listed).

  I have the latest drivers for the disk (9Q23_Storage_Driver_X6KKJ_WN_11.5.0.1207_A01. (EXE)

  Are there available firmware, and if so where is it please? Otherwise, what is the next step?

  Thank you.

  Thanks, EJN - F12 diagnostics appear clean. I guess that I'm worried about this then.

• SMART short Self Test Failed - (error code: WHD16-8NR)

  Hi all

  I had my XPS L520X for 4 years and 2 months. I've never had a problem with its operation until last week. Randomly, it restarted and came with the PCI Realtek issue when it restarts.

  To cut a very long story short Fault find it which is going on, I reinstalled the entire operating system, including formatting of the hard drive.

  The problem of the laptop different freeze/crash and reboot with erros while doing normal tasks has not been resolved.

  I have run the Dell support center software and it shows the auto SMART test failed with the following code (error code: WHD16-8NR).

  Event log:

  Dell Support Center log file
  March 17, 2016 16:53:55
  Overall result: failed

  -------------------------------------------------------------------------------------------------------------------------------------------
  ST9750420AS [ATA:0:0\\?\ide#diskst9750420as___0005dem1#4&34e0611c&0&0.0.0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b]}
  -------------------------------------------------------------------------------------------------------------------------------------------

  Seller: Seagate
  Model number: ST9750420AS
  Serial number: 6WS100EG
  Firmware revision: 0005DEM1
  Size: 698,6 GB
  Rotation speed: 7200 RPM
  Cache size: 16 MB
  Temperature: 43 c
  Physical sector size: 4 KB
  Logical sector size: 512 B
  Count of logical sector: 1465149168
  Supported standards: ATA8-ACS, ATA/ATAPI-7, ATA/ATAPI-6, ATA/ATAPI-5
  Specification Version: Rev ATA8-ACS 4

  ----------------------------
  OS - C: [PARTITION:C\\.\C:\]
  ----------------------------

  File system: NTFS
  Volume serial number: 5087-8802
  Volume capacity: 679.00 GB
  Amount of free space: 568,63 GB
  Volume space used: 110,37 GB

  Test of the SMART State

  Test started - 17/03/2016 16:43:57
        
  Finished test:-17/03/2016 16:43:59
  Past

  Test of SMART thresholds

  Test started - 17/03/2016 16:43:59
        
  Finished test:-17/03/2016 16:44:01
  Past

  Targeted reading test

  Test started - 17/03/2016 16:44:01
        
  Finished test:-17/03/2016 16:44:05
  Past

  Try to search randomly

  Test started - 17/03/2016 16:44:05
        
  Finished test:-17/03/2016 16:44:54
  Past

  Funnel Seek Test

  Test started - 17/03/2016 16:44:54
        
  Finished test:-17/03/2016 16:46:14
  Past

  Short what SMART self-test

  Test started - 17/03/2016 16:46:14
        
  Error message:-17/03/2016 16:46:24
  The unit has reported the following State: the previous self-test completed having the read element of the test failed.
  Error message:-17/03/2016 16:46:25
  The first default LBA value is 121243744 and the failure occurred after that the device was working since 8792 hours under tension.
  Finished test:-17/03/2016 16:46:26
        Failed (error code: WHD16-8NR)

  Surface Scan Test

  Test started - 17/03/2016 16:46:26
        
  Finished test:-17/03/2016 16:47:25
  Past

  Surface Scan Test - 2

  Test started - 17/03/2016 16:47:25
        
  Finished test:-17/03/2016 16:48:58
  Past

  I also went in the BIOS BOOT MENU by pressing F12 at startup and ran diagnostics that seemed to have said everything going, however I saw a mistake, faliure in its process that was too fast for me to write the error.

  In a nutshell, my thought is that my hard drive has failed / is corrupted or is about to fail.

  My simple question is, do I need a new hard drive with the information I've provided?

  Thank you very much!

  To all those who read this topic:

  I rang Dell directly and they confirmed my hard drive needs to be replaced.

  8792 power over time, I think that its actually me good.

  Bravo and thanks for the reply ejn63

• Compaq presario v6000 v6409tu disk hard bios self-test fail

  Hello

  Windows xp no my pc compaq v6000 not starting and bluescreen showed a couple of times. I ran the BIOS (phoenix) disk hard diagnosis and the test failed. When I opened my HDD I noticed green rust as deposits into the connector on the hard drive. After cleaning with a brush, computer loaded XP successfully. But an hour later, while I was surfing in mozilla suddenly the mouse pointer started late and showed computer blue screen saying that windows has been closed down to prevent damage.

  I would be grateful if someone can tell me if it's a software problem or hard drive error. If I need to replace my hard drive, what are my options, for example. rpm, capacity, provider? Thank you.

  The only way you could have rusted copper into the connector on the hard drive is if liquid got in there so I am reluctant to try to speculate how much damage has been done. I remove the hard drive and connect it to the outside to another computer and run chkdsk on it to see if the drive itself is bad. As long as there is a problem on the part of connector and the interface with the motherboard cannot really trust the onboard hard drive Diagnostics. You could also get an own another new hard drive adapter.

  http://www.eBay.com/ITM/new-Compaq-Presario-C700-F500-F700-V6000-SATA-laptop-hard-drive-connector-/161297513053?PT=US_Drive_Bay_Caddies & Hash = item258e14ba5d

  If it does not turn on the hard drive is bad, you can replace it with any laptop SATA drive no more than 9.5 mm thick.

  http://www.Newegg.com/product/product.aspx?item=N82E16822145587

  Above is a good thing. It is slim (7mm) but it will still go into the caddy and connect to the motherboard with the connecting piece. If the hard drive itself is always good, and you replace the connector piece but he always bluescreens, so I would not spend money on a new hard drive. I would say that there was damage to the motherboard.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Targeted Test read and Smart short self-test failed!

  Help, please! Is there something to fix the underside of chess? Product: XPS 435 t/9000.  Western Digital: WDC WD5000AKS-75V0A0. The crash occurred after that my Tripp-lite didn't work properly in a power failure. Targeted reading test
  Test started		17/09/2013-09:22:13
  Error message:	Error reading sector 27214298.	17/09/2013-09:22:34
  Error message:	The test found errors in sector 1.	17/09/2013-09:22:34
  Completion test:	Failed (error code: WHD20-B3A)

  Short what SMART self-test
  Test started		17/09/2013-09:25:03
  Error message:	The unit has reported the following State: the previous self-test completed having the read element of the test failed.	17/09/2013-09:26:15
  Error message:	The first default LBA value is 27214298 and the failure occurred after that the device was working since 13979 hours under tension.	17/09/2013-09:26:15
  Completion test:	Failed (error code: WHD16-3DY)

  Jan

  It is likely that you will need to replace the hard drive.  To confirm, press F12 at startup, enter the Dell diagnostics.  Run an extended hard drive test.

  If the system is under warranty, logs the error and contact Dell for a replacement drive.

  If the system is out of warranty, any standard 3.5 "SATA drive will work as a replacement.

• HDD self-test - Fail #1-04

  Hello
  I have Pavilion dv9000 series (dv9040eu), all of a sudden, I get the BSOD with impossible to mount the volume message, so I run disk hard test, which returned: # Fail 1-04

  What does this error mean?

  is there a place where I can read the explanations of the error associated with the HARD drive self test?

  I tried running chkdsk/r, but it keep saying "an unspecified error has occurred", also, I managed to get the most important files, with "BartPe" and "GetDataBack".

  Starting recovery console also causes the BSOD with message unmountable_boot_image...

  Any suggestions?

  Many thanks in advance...

  Message edited by sourpuss on 05/01/2009 08:39

  No, a car will be empty, but if you their Envoy the laptop and then they put the reader, they may then be able to do that, but I expect it to be cheaper to just order the recovery DVDs too and DIY.  Because the discs cost a lot of HP, I recommend only the recovery DVD from them and purchase the disc elsewhere.

• PCI-6132 self-test failed

  My card PCI-6132 at some point began to generate error (code error-50400) during the race. It does not pass to the MAX OR self-test with the same error code. As I see that one of the chips, I think it's a shame. We bought a long time ago, so the warranty has expired. So my question is what it can be caused by? And how can I avoid this in the future? Can it be fixed or I just replaced this card?

  I apologize for my previous post, which indicates that this type of behaviour can be expected.  I want to clarify that we certainly do not expect these damage with our products during operation in the specifications.

  I encourage you to contact OR by phone to set up an RMA for the Board so that it can be repaired and futher diagnostic.

• SMART extended self test failed

  Is this what can I do to repair my disk hard when diagnostics the system returns this error message?

  The read element of the test failed (error code: HD521-3W)

  Is there available utilities to diagnose the problems of internet connection on HP?

  Thanks for any help anyone can give me.

  Michele

  Unfortunately, the result of this test tells you that the hard drive has failed, you will need to replace the hard drive.  You can save your data by installing the drive on another PC using one of the spare hard drive SATA connections, if it is a SATA or IDE secondary connector if the drive is IDE and try to read the disc in windows, but it depends on how much the failure of hard drive is. The reader may not even be readable.

• Hard drive failure: targeted read Test failed, SMART short self test FAILED

  Suddenly, I get this popup to My Dell saying that my computer has failed two important tests and the hard disk failure is imminent. It scared me so much I almost fell of my computer Chair, so I came here to help... my computer is a Dell Inspiron 15R 2012 5520 and error codes are:

  

  I saw the other topics on this, but just in case, I wanted to do this one. I'm really afraid that all my files will be lost, because I don't have anywhere to store up to. I tried the cloud, but my connection is not good enough and it is really slow and sometimes just will not work. Also, sometimes when I press my ear to the laptop, I hear a soft grinding, which I guess was the failed hard drive. I don't think I've heard that noise before, but he could have been there since I bought the laptop.  Any help would be greatly appreciated.

  UPDATE: I ran CHKDSK and it only took a few seconds for him to know that my hard drive is fine, although my Dell seems to think otherwise. What should I trust?

  4590 X

  You will need to replace the hard drive failed, followed by reinstalling windows.

  If there is a warranty from Dell, contact Dell technical support for replacement drive, no guarantee, you will need to purchase a laptop SATA, 9.5 MM x 2.5 "hard drive.

  With regard to the recovery of the data files and folders, you can try attaching the failed hard drive to another system that works using a similar to THIS USB adapter and see if you can transfer files and folders.

  Applications and programs need to be reinstalled from their records, or downloaded from the website of the Publisher.

  Bev.

• Smart short self-test failed. HP Pavilion p6232p Desktop PC with nothing installed again.

  1

  Hello:

  This message usually means that the hard drive has failed and needs to be replaced.

• DAQmx for DAQcard6042E fails the self-test. Inherited data acquisition is OK.

  The computer I'm working on was provided by my client with LabVIEW 7.1 and the 6024E installed.  They had obviously written a program or two with this configuration, using Legacy DAQ screw.  (Of course) I would use DAQmx instead, but I'm having no luck.  Self test fails for inscription on the list of Council DAQmx (error-88705) MAX, but that's OK under traditional DAQ.

  Versions: LabVIEW 7.1

  (run 7.0, 7.1, 8.0, 8.2)

  MAX 4.1.0.3001

  NOR-DAQmx 8.3.0f0

  7.2.of1 OR-DAQ trad

  Any ideas?  Thanks if you can help!

  Hi Spencer60!

  This error message is generally returned when the Windows Service OR charger device (or "nidevldu") does not work.  Take a look at the following KB and let me know if you have any other questions.

  Device charger OR (nidevldu) and NI Configuration Manager service does not start

• The hardware diagnostic tool advises that the SMART short self-test has failed.

  The hardware diagnostic tool advises that the SMART short self-test has failed.

  Is this a problem? What can I do about it?

  Atelier42 wrote: the hardware diagnostic tool advises that SMART short self test failed.

  Is this a problem? What can I do about it?

  Hello Atelier42, this usually indicates that you have a hard disk failure.

  I would like to back up my data as soon as possible, just in case the hard drive breaks down actually.

  You must also make sure that you have the HP Recovery restore set for your system recovery disc in case you do not want to replace the hard drive.

  With this restore HP Recovery disk set, you could replace a defective hard drive and use this disk set to your HP system back as it was when shipped. Then, you could put your data saved on your system.

• PCI-5922 self-test error-223431

  I try to reset PCI-5922 OR MAX and get the error code 80040383:

  "There was a problem of resetting the device."

  Then I try the automatic test of NOR-MAX and get the State Code:-223431

  "The self test failed.

  State code:-223431

  Internal software error has occurred in the extended software. Please contact National Instruments. »

  I have tried following th:

  1. reboot the computer

  2. Uninstall and reinstall OR-Scope 15.1.1

  3. change of PCI slot

  After a few tries it turns out that the problem was in the computer. When it is installed in a different computer, the PCI-5922 worked properly.

  Now, it seems obvious: when troubleshooting

  1.) install the Board in another computer

  2.) install another identical sign (if you have one) in computer suspiciuous

  Yonathan