N40l

Similar Questions

• N40l Microserver does not illuminate. Switch will not do anything.

  Team,

  I have a micro N40L server that I use a home theater media server. It has been sitting in my living room for a few years, quite happy.

  This week, possibly after a power failure, the server couldn't start. I noticed he was sitting there with the power button showing amber in color and the HP logo on the front panel was not lit.

  I tried to hold down the power button but the yellow light remained on and the server did nothing.

  If I removed the power cable there is a click as I plug it back, the light orange light. The only light is the light of network activity that flashes from time to time, as it was still plugged into the network.

  No fans run, no disc no boot, no output to the screen through the graphics card Radeon HDMI. Even the bios page will appear.

  I am assuming that the power supply may have failed. Can what tests I do to find the flaw?

  Would it be a defective switch?

  The operating system running a Windows Server 2008.

  He had two drives, 250 GB system drive and a single drive of 500 GB data. No RAID has been configured.

  The only addition is a Radeon graphics card.

  Any ideas what to try?

  Thank you

  AJ

  You are right, the problem was caused by the power switch blocked.

  After some insistence, it is still blocked, but with the help of the post.

  Improvement of Hugh until I can get it replaced.

  Thanks for your help...

  DM

• Installation of Windows Home Server 2010 on Proliant N40L

  Does anyone know if Windows Home Server 2010 will install on a Proliant N40L without having to install additional device (for configuring SATA RAID) drivers.

  I can't install again, that my DVD drive is IDE not SATA, I'm waiting for a new. Once this drive shows up, I'll be able to find out for me.

  Well, the answer was that the installation went very well. I didn't do anything to Windows Server 2011 to recognize the RAID adapter.

• Find the optical drive data cable (Proliant N40L)

  Proliant N40L is provided with a data cable to the DVD player that I need to install my system? As far as I know, mine is not.  I consulted the slot in DVD player and found the power wire, but no cable (IDE motherboard) data.

  If I buy one, where is a good place to find a?

  Hello

  Proliant N40L does not use the EIDE interface.

  

  It uses the standard SATA. When you buy a SATA DVD to install, buy a SATA cable at the same time. They are inexpensive.

  Best regards

  ERICO

• Installation of Windows Server 2011 on drives mirrored in N40L

  First POST:

   

  Happy (and successful) New Year to you!

   

  I just got my N40L Proliant, and I intend to mirror the boot drive before you start the installation of the OS. Will it take the RAID driver on "floppy" in order to install Windows Server 2011?

  Literature talks about the creation of a floppy disk, but before that I have to create a floppy drive!

  I'm working my way through the documentation, but it was not written for people with symptoms of dementia of old age... so I decided to ask here, in the hope that someone else has tried this recently and can give me a straightforward answer.

  I think that just, I freaked out when I saw the word "floppy". Probably if I need to install RAID drivers during the operating system installation phase, then they would have to come from a USB key, as seems natural replacement of disks (I have a bunch of those covered in 20 years with a value of dust...)

  Hello:

  And a very happy new year to you too!

  Welcome to the HP consumer support forum.

  I recommend that you also post your question in the HP business - Netservers section support forum where you can get more help.

  http://h30499.www3.HP.com/T5/ProLiant-servers-Netservers/BD-p/BSC-431

  Best regards

  Paul

• Insuficient memory on HP N40L

  I checked the specifications min for esxi 5 running on this server, and it says 2 GB. I don't want to increase the ram soon but the atm, he has only 2 GB in there. However, trying to install esxi, it stops and reports that it requires that at least 1.97 GB of ram and the maching have only 1.87 GB? Has anyone else had this incorrect scan of Ram to try to install it on a servers HP? Any solution please?

  its probably of RAM allocated to video memory.

• AMD raidxpert

  Hello!

  Question about HP Microserver N40L

  I am tryin to find any cli for raidxpert utils. On the web is not enough for me - would like to output simple txt mode like hpcucli or hrconf

  TNX!

  He fixed selfmade: python + selenium + firefox = had .py script. It returns 0 or 2 exitcode - this is for nagios - ok or critical

  some Cyrillic inside - don't panic, use EN or another status line in your case. A commented some for internal use.

  #! / usr/bin/env python
  #-*-coding: utf - 8-* -.
  Selenium import webdriver
  from selenium.common.exceptions import NoSuchElementException
  from selenium.webdriver.common.keys import keys
  time of import
  import re
  import sys
  
  browser = webdriver. Firefox() # Get local session of Firefox
  Browser.get ("https://127.0.0.1:8443/amd/login.jsp") page Load #")
  say 'AMD RAIDXpert Вход' full name browser.title #, with the current language of firefox - en-... Opening of session
  elem = browser.find_element_by_name ("login") # find the query box connection
  elem. Send_Keys ("admin")
  elem = browser.find_element_by_name ("password") # find the password query box
  elem. Send_Keys (("***") + Keys.RETURN)
  Time.Sleep (0.2) # allow the loading of the page, will be added to the API
  Browser.get ("https://127.0.0.1:8443/amd/objMod.jsp?object=daSet_0_100942741_0") # raid unique for each server - status page!
  HTML = browser.page_source
  #uncomment if needed after the html page.
  #replaceAll(html,"utf-8","cp1251")
  #f = open ("pagedump2.html", "wt")
  #html = re.sub ("#ffffff", "#000000", html) white #stuppid police on white page
  #f.write (re.sub("utf-8","cp1251",html)) #and for Cyrillic fix
  #f.close)
  If 'Функциональный' in html: # in EN Firefox - 'functional '.
  #print ("Функциональный")
  sys.stdout.Write ('0' + '\n')
  Another thing:
  # print ('gradient')
  sys.stdout.Write ('2' + '\n')
  Browser.Close)

• ESXi 5.5 only 4 TB usable for the data store

  Hi all

  Although in vSphere Client 5,46 TB of capacity is visible, I can only use 3.64 TB to a data store.

  Configuration:

  -HP Proliant Microserver N40L

  -HP Smart Array P410/512 MB BBWC, FW 3.66 Controller

  -4 x 2 TB as a Raid5

  HP-ESXi - 5.5.0 - iso - 5.72 A

  I read a lot of articles on > limits of 2 TB of older versions of ESXi or controllers, limitation of 4 TB of c# vSphere Client, old firmware and esxi driver problems, etc.

  But I could not understand the problem.

  The P410 controller shows 5.5 TB:

  ~ # esxcli hpssacli cmd - q "controller connector = 1 see the config.

  Smart Array P410 in slot 1 (sn: PACCRID110510NR)

  Array A (SATA, used space: 0 MB)

  logicaldrive 1 (5.5 TB, RAID 5, OK)

  then 2I:0:5 (port 2I:box 0:bay 5, SATA, 2 TB, OK)

  then 2I:0:6 (port 2I:box 0:bay 6, SATA, 2 TB, OK)

  then 2I:0:7 (port 2I:box 0:bay 7, SATA, 2 TB, OK)

  then 2I:0:8 (port 2I:box 0:bay 8, SATA, 2 TB, OK)

  MS (Vendor ID PMCSIERA, model SRC 8x6G) 250 (WWID: 5001438013D9F37F)

  ESXi obviously knows the same size:

  ~ # Esxcli storage core devices list

  NAA.600508b1001ca5e68adc0bc4bc508d6e

  Full name: Serial Attached SCSI disk HP (naa.600508b1001ca5e68adc0bc4bc508d6e)

  Definable display name: true

     Size: 5723091

  Device type: Direct access

  Multichannel plugin: NMP

  Devfs Path: /vmfs/devices/disks/naa.600508b1001ca5e68adc0bc4bc508d6e

  Vendor: HP

  Model: VOLUME LOGIC

  Review: 3.66

  SCSI level: 5

  (etc.)

  But does that 4 TB:

  ~ # df h

  Size of filesystem used available use % mounted on

  VMFS-5 T 3.6 2.1 T 1. 5 t 58% / vmfs/volumes/mainstorage

  vfat 249.7 M 177.2 M 72.6 M 71% / vmfs/volumes/aeda2aeb-c934ad60-46ce-cb77abdfabaa

  vfat 249.7 M 175.9 M 73.9 M 70% / vmfs/volumes/c8ace7e9-a96a5914-16 d 4-a697ad4634d9

  vfat 285.8 M 191.4 M 94.4 M 67% / vmfs/volumes/55d7af6e-a25f7c97-c3ec-6805ca0de93c

  I tried to increase the size of the data store, last used area was 11720890367 and last sector was 11720890510 which doesn't really seem to translate into an increase of 1.8 to.

  Thanks for your help.

  DC

  Your output, it shows that there are two partitions vmfs

  3 10229760 3907029134 AA31E02A400F11DB9590000C2911D1B8 vmfs 0

  4 3907031040 11720890367 AA31E02A400F11DB9590000C2911D1B8 vmfs 0

  A partition with 1.8 to and another with 3.8 to.   That's the reason why you see only 3.8 to

  I don't know why the 1.8 to vmfs volume is not list anywhere (which does not appear in the list of file system of storage of esxcli also). Do you have any before partition created manually. If you think that if there is no data in this 1.8 to vmfs partition you can remove it by using the partedutil command and then use this free space to extend the existing 3.8 to. But do not forget before you delete the partitiaon

• ESXi host has no persistent storage / fsUUID is null

  Hello

  The issue I'm having involves a HP N40L Microserver w / local storage on a HP SmartArray P410 controller.  6 hard drives configured in a RAID10 array and the multitude of ESXi what OS runs on local USB.

  A recent issue w / the matrix raid caused a crash of the VMS resident and now "host ESXi has no persistent storage" message.

  I solved the problems of disk HARD w / table (replaced a disk), and the table is presented in the peripheral topic under "HP Serial Attached SCSIDisk.  ID is naa.600508b1001c8d82bf5f4a33f0e2bc04

  However, the data store does not appear in the tab of data warehouses.  I refreshed and restarted several times w / no success.

  This data store was run on an installation 5.1 ESXi (ISO custom HP) for a few years without problem.

  To try to solve the problem, I installed ESXi 6.0 U1 on a new USB stick which fortunately is now running in the Microserver but presenting the same behavior for the data store.

  Output of list of file system of storage of esxcli-

  Mount point

  Name of volume UUID

  Type of mounting

  Size

  Free

  -------------------------------------------------  -----------  -----------------------------------  -------  ----  ---------  ---------

  / vmfs/volumes/56b8f1c5-732f51cf-68ec-a0b3cce4eb3a	56b8f1c5-732f51cf-68ec-a0b3cce4eb3a	299712512 88342528 true VFAT
  / vmfs/volumes/bd8588e2 - 04362b 85 - E425 - db3beeb1519c	bd8588e2 - 04362b 85 - e425 - db3beeb1519c	261853184 261844992 true VFAT
  / vmfs/volumes/fd2695e7 - 253111b 8 - b8f2 - 4a0b47e4542e	fd2695e7 - 253111b 8 - b8f2 - 4a0b47e4542e	261853184 69287936 true VFAT

  Esxcfg-scsidevs output - c-

  UID device	Type of device	The console device	Size	Multipathing PluginDisplay name
  MPX.vmhba32:C0:t0:l0	Direct access	/VMFS/devices/disks/MPX.vmhba32:C0:t0:l0 Mo 15484 NMP	USB Direct-access local (mpx.vmhba32:C0:T0:L0)
  NAA.600508b1001c8d82bf5f4a33f0e2bc04 Direct access	11446225MBNMP	Serial Attached SCSI disk HP (naa.600508b1001c8d82bf5f4a33f0e2bc04)

  I'm trying to go back through the list of commands, I tried to get more information and at some point received a response from "fsUUID is null" when you try to search the naa identifier.

  All the input welcome, thank you.

  Please tell me what FreeNas has to do with this?
  I'd say we look closer together. If you want to - call me through Skype
  Ulli

• Laboratory at home - will this work?

  I'm not familiar with ESXi capabilities or it is that I've never experimented with a bare metal hypervisor. I would like to know if what I have in mind will work before investing my time and money into this project

  Objectives - build a ZFS NAS bases / syslog server under a card for my lab at home

  Material

  N40L - Dual-core 1.3 GHz AMD Athlon Microserver HP 2 - NC107i PCI - e Gigabit NIC. I'll add one extra gigabit NIC as well.

  I'll put the max 8GB DDR3 ECC RAM

  For storage, I have to make a minor mod so I can get 5 x HD machine comes with 4 drive bays, so I'll put disks SATA 4 x 2 TB to use as storage RAID-Z. I want to add a shopping cart to drive for 5.25 inch optical drive to install an additional SSD used for these two VMS operating systems. Here is a link for someone who has done the mod - http://paulroberts69.wordpress.com/2012/01/22/installing-a-hdd-in-the-optical-drive-bay-on-an-hp-microserver-n40l/

  Configuration

  In the end, I want to have 2 virtual machines running on this computer.

  VM1 - FreeNas 8

  VM2 - FreeBSD or Linux used as mainly a syslog / web server

  Questions and concerns. Will it be possible?

  I want to start ESXi on internal USB port of motherboards.

  I'll be able to install the operating system of these two virtual machines if I partition the SSD added that I installed in the optical drive Bay?

  The FreeNas VM will be able to configure the RAID-Z among the 4 SATA physical disks?

  Each virtual computer will be assigned it's own physical NIC because they will run on 2 separate behind my pfSense firewall network segments. I don't have any image it will really be a problem if I used it in network bridge.

  If this is not possible, I'll probably install FreeBSD on its own and try to get my setup above to work. I'm not familiar with FreeBSD and I want the nice interface of the FreeNAS GUI to manage my storage and Samba shares, so that is why I want to virtualize.

  Advice or advice is greatly appreciated.

  dafunkphenom wrote:

  I think I'll have to sacrifice the RAM. It looks like buy sticks of 2 x 4 GB RAM ECC would cost me about $450. The box already comes with a 2 GB module, so if I buy another 2 GB directly from HP module I can get it for $70. I doubt I need 8GB to my config anyway.

  Try to search in Kingston or other compatible memory instead of HP original.

  I was looking here (Europe, Switzerland) locally and them found for about $ 40. Kingston is the list this memory as KTH-PL313E / 4G

  $600 tax Inc. for the Microserver.

  $400 for 2 x 3,5 "SATA 2 TB + 1 x 120 GB SSD (I have already 2 x 2 TB drives kicking around and I have a PCI-e Gigabit NIC to an old box)

  $70 for 2 GB ECC memory module

  So probably all said and done between $1000-$1100 taxes. I'm from good old (Ontario) Canada.

  Ah, got a few distant relatives in and around London (Ontario).

  Greetings from nightly from Bern, Switzerland