NAS200 disc?

I have the NAS200 with one disc.  I would like to delete the NAS200 unit hard drive and use it to access the same files on a removable USB adapter.

If I simply remove the drive and plug it into the usb, the computer box can see the drive, but can not read one of the info on the drive...

Anything I can do to make this work?

The NAS200 uses ext2 for non journaled partitions and XFS for logged partitions. You should be able to read it with a machine Linux that supports these file systems. Under Windows, there is a program called ext2ifs who works with ext2, but I'm not aware of all the Windows XFS solutions at this time.

= Jac

Tags: Linksys Products

Similar Questions

  • NAS 200 change disc journaled format = > not logged

    Hello

    I read in the forum that change journaled disk format to non logged can accelerate access to the drive, but is less secure.

    I use 2 disk in my nas200 2 years.

    What is the level of appreciation of the speed I could expect?

    How can I change the disc format?

    What kind of titles cannot compensate for the change of format of disc about the integrity of the data?

    Thank you very much

    Will improve the speed by about 50%.

    Worth of security, is that if you have a power failure while writing to a file, this file may be lost. The risk of loss of data because of power failure is much lower in logged mode.

    You can change that by reformatting the drive, which will erase all your files. If you need to back up your files before you do and restore them later. Of course, this will take a very long time (perhaps several days, depending on the size of your discs).

    You can save time by using SystemRescueCD on a PC with the NAS200 disk connected to your PC to copy the data to another drive before we do the reformat. Then you can put the disc into the NAS and reformat. Then put the disc on the PC and use SystemRescueCD to copy files back. Do not use SystemRescueCD to reformat; the NAS will have to do.

    = Jac

  • NAS200 after power supply current

    Hi all

    could you please confirm this behavior after a power failure:

    -the Sin starts normally and for a few seconds I can access via the web. But if I try to force the closure, he answers me back is not possible due to the scandisk is underway

    -After 2 minutes, where the green light turned on I see the two light of the two bays which lie on. The problem is that the I only have one disc inserted into the SIN!

    -the system is not accessible. I read the manual it is normal when the sin is the scandisk. But it is not clear to me it does, because flashing power/ebaydisk1 noither.

    Any suggestion?

    When the NAS200 sees that the disks were not closed properly, he made a blink of LEDs from disk at startup for you know that it is the cleaning of discs; they stop flashing when the cleaning operation is complete. If I understand correctly, this is not what you see: you see two disk lights on.

    Normally you should never see both lights of disc on if only one drive is installed. Try unplugging the power supply and then restarting him. Maybe it was just a small problem and it runs very well this time.

    If it's the same thing when restart you with the installed drive, try running it without disc and see if the lights are still to come. Both hard drive lights should turn off if no drive is installed. If they remain, you may have a hardware problem that causes the software hang (or perhaps to trigger a kernel panic).

    If it starts fine without the disc, but both lights keep coming with a disc, there may be a problem that can be fixed by connecting the drive to a PC and booting with a CD of SystemRescueCD. You may need to ask someone who knows Linux to help you with that.

    = Jac

  • NAS200 JBOD/LVM scandisk fails

    Hello

    as I set up my new NAS200, using disks 2x1To as a disc in JBOD mode, scandisk fails every time. Newspaper accessible via the administrative Web interface, a scandisk boot process leads to the entrance of the newspaper " LVM: ' (i.e. no results are saved!)" or "": scandisk failed '. " I use the latest firmware version 3.4R79.

    To try to solve this problem, I tried the following two:

    * I changed the firmware JAC4, connected via SSH and descended from xfs_repair, with the result of the SIN all suspended after xfs_repair for maybe 15 minutes running, but before he finished (after agno2).

    * I have detached the two discs of the NAS, attached to a PC, started using Knoppix 6.2 and made xfs_repair on the logical volume with no problems (in 40 seconds). I have attached the two drives on the NAS again, but still no scandisk initiated through the administration Web interface!

    What - what, there is a problem with the firmware?

    Are there other balls to distinguish who said to me why scandisk fails?

    Will I go back to JAC4 and run scandisk via SSH using different commands?

    I would like to regain my confidence to the NAS200...

    Welcome,

    Martin

    mbern wrote:

    However, when I try to test on the NAS via SSH and xfs_repair, the process fails. So far, I thought that the process crashes, but now when I try again, it seems that, indeed, the xfs_process is killed by the operating system:

    The program can be killed by oom_killer the kernel if it allocates too much memory too quickly. If you had a serial port on the console, you would be able to see. Another way to see if this happens is to start /etc/rc.syslog (she normally doesn't start) and enter the command "tail-f var &" so that syslog messages are dumped to your ssh session where they occur. Don't forget to disable syslog again by entering "killall syslogd, klogd" and remove var because they eat RAM too!

    The time-out that I referred to has a possible timeout the web GUI can be used when it is waiting for the xfs_repair program. Of course, if you start the command line xfs_repair this applies to you.

    mbern wrote: too bad that they tested it with 750Go only, I wan't able to find a good official statement (on the Web page, in the manual). But I remember my dealer claimed the support of 1 TB, otherwise I would not have bought the NAS with two 1 TB drives. I also used the NAS in Raid 1 with drives of 1 TB without worries as above.

    The manual and the site doesn't mention that they have tested with 750 GB drives, they just mention (mentioned?) that drives up to 750 GB are supported. I guess they have tested with larger disks as possible...

    I use a drive 1 TB and never had no problem, theoretically there could be a problem if you install a disk that is longer than 2 TB (tera-byte binary) because this corresponds to the maximum value that can be managed by access 48-bit LBA. Most likely, the readers with a capacity of 2.5 (decimal) to claim are the first readers who won't be able to use 2 (binary) TB because of this problem. I have not seen all reports of anyone using the latter on a NAS200 yet.

    = Jac

  • NAS200, UN-configure the public default drive

    Hello

    I have a NAS200 with 2 drive public, configured by default.

    I now want to configure more users and limit the use. But it seems that the Public record are always public and cannot configure the authorization it. I also have the latest firmware.

    My question is if I can rename the/public folder to something else and then re - share with the same share call 'Public disc 1?

    Current configuration:

    Disk1/public is shared as 'Public disk 1 '.

    I want to share Disk1 as 'Temp', then rename the public folder and then delete the share and create a new one.

    Is - is this posible? I lose data?

    Thank you very much

    Oliver

    It is not possible to rename, delete the "DISK 1" and "PUBLIC DISK 1" actions (or the "DISK 2" and "PUBLIC 2" DISK sharing if you have two disks ").» You also you can not move the sites referring to these actions.

    However, you can hide these actions of all users and create new actions that relate to any location on your disk (s). For example, you can create a user 'jac' and a 'jac' share and modify access rights so that the "jac" user doesn't have access to "DISK 1" or "DISK PUBLIC 1" but only in the directory "jac". "". " Whenever the "jac" user on the NAS, he sees only the directory "jac".

    IMPORTANT!

    If your problem is that you're setting up of actions and not see them properly to your PC, it probably means that you are connected as a guest. Disable the "convert failed connections connections comments' (or completely disable comments connections) on the System Options page.

    = Jac

  • NAS200 Raid1 - disk 2 has failed, cannot rebuild

    When the failed drive, the green light for the first disc was there but not for disc 2.

    By going to the web server the States said that disk 2 was not inserted (and this is obviously false).

    There was a lot of information on the problem when I Googled it but nothing seems to work.

    Configuration:

    • NAS200 in Raid1
    • 2 identical drives: Western Digital 500 GB (WD5000AAKS)

    I tried:

    • Do a manual backup using linux and mdadm function to mount the drive. Result: Cannot ride because he can't find the superblock.
    • Using the command mdadm - review. Result: «State: clean "," devices Failed: 0 ", etc (nothing seems bad).»
    • Buying a new drive, threading instead of fail and let the NAS200 reconstruction. Result: It's been 2 days now and the NAS reboots always rebuild... the best I can see is "1% complete" and it restarts again.

    There are very important information on the disk. My first priority is to recover this information. Once it is I'm not reformatting of records care and reset the NAS200.

    I hope someone can help me, thank you very much.

    -Jonathan

    I don't think that can be recovered... However, try this link.

  • NAS200 records

    Hello! I have a NAS200 (2 x 1 TB HDD) set up by the other guy in stripping Raid (raid 0)

    It's the folder structure (with read/write access

    )

    public folders size disc is the same with the size of public folders

    I don't know if one of these folders (public, public record) is a backup or a link.

    I want to raid 1 for better file integrity NAS200 and now I have to do a backup, but I don't know whatis with these files

    To perform a backup, you'll need is the DISK folder. Other public records are references to the same data: If you put a file in (say) DRIVE PUBLIC it will be also displayed in DISK\public and if you remove the DISK PUBLIC files it will also disappear from DISK. DRIVE represents the root directory of the drive, you can consider other file shares as shortcuts to the subdirectories under the DISC. The only reason to have multiple shares that have the same data is to define different access on different actions. For example, you can ensure that only the administrator has rights on the DISK, catsuzana has access to poze, jac poze access and sharing DISK PUBLIC etc.

    Also when you perform a backup, you can also make a backup of the configuration via the web GUI (at the bottom of the Firmware Update page).

    = Jac

  • NAS200 drive failure

    I have a couple of configuration NAS200 do RAID1 on the internal disks. On a single unit, I was checking the status on the WEB Interface and it shows "Disk 2 - Failed" on the status screen. However if I check the drive using SMART Disk utility screen it says it's OK, and when I run Scandisk on the RAID logs show "RAID 1: Scandisk finishes, no error found.". The lights of disc at the front of the case also indicate that everything is OK. Is OK disc 2? If so how can I get rid of the message failed in the status?

    Hello

    If you are convinced that there is no problem with your 2nd drive then you can try to do these steps.

    1. turn off the NAS.

    2. unplug the readers on during seconds then reconnect.

    3 rotate on the NAS and watch the lights on the device until it stabilize

    4. try to access the user interface of the NAS200 again and check the status of the two drives.

    Let us know what happens then.

  • NAS200 telnet? fsck? Lost + found? Help me please.

    Hello world.

    I NEED to access the NAS200 drives.

    Somehow my file system was broken.

    Yesterday I was copying some files on the device (attached to a dedicated UPS, so no power failure when writing) during the copy (it was long) I tried to delete some files in a different folder.

    The player responded: removal of the files had a life (even if the copy is complete) it took about 40 seconds to delete each file...

    So I decided to cancel the operation and restart the device.

    I pressed the power button, I heard the stop sound and turns off after a while.

    I turned on it once, it happened as usually: leds (power - activity - disk1 and disk2), beeps...

    Then I tried to access my files, but vista gave me a network share could not be found.

    First of all, I ping the device, he was there.

    Then I have connected to the web management, made a successful logon, checked state.

    All right: two recognized discs. Chip Disk1: OK, chip Disk2logical disk K 0 (raid 0): ok.

    Total space 1, 5 to, free space 200 GB.

    I tried with the web service "access to my files"... and then, I throw a shout!

    I got an error, something like 'Path of ACCESS not FOUND' (previously I had two /DISK and /PUBLIC_DISK actions)

    Then I tried again with FTP (same error)

    Then I launched "Scandisk" (still within the management interface) in the newspaper I see "scandisk has failed."

    I tried to launch it again and after one hour, the unit was not responding.

    Is there a way to access the ext3 FS without the web interface?

    How can I make fschk?

    I need to recover the data

    I have lots of photos & videos of my babies when they are born, working documents, working source code

    Any tips?

    What can I do?

    (Material) discs seem to be ok.

    The raid goes to the top.

    The file system appears to be damaged but not bad (or I don't know disk space / free)...

    If the disk file system are not accessible through NAS200 can I connect the disks in a PC with linux and a raid controller? Or is the only raid array works with the controller in NAS200?

    Please help me.

    Thank you in advance.

    The RAID is a software RAID using mdadm. If you have a Linux system, it should be easy to mount hard drives SATA or eSATA or (at most) a USB to SATA converter. If you define for the journaled file system, the NAS200 uses XFS. It uses ext2 for not journaled.

    If you connect the disks on a Linux machine, you will find 3 partitions on each disk: (1) the data partition, (2) a configuration partition, and (3) a swap partition. I do not recommend making any changes to the configuration partition unless you know what you're doing.

    Connect the drive on a Linux system is going to allow you to recover things MUCH faster that to do with the NAS200 (who is actually a PC 133 headless of 486 MHz which feels like it is clocked at 100 MHz).

    If you insist to leave readers in the NAS and you wish to SSH or Telnet access, you can install my firmware . It will not affect your configuration or your hard drives, it will always be like the Linksys firmware (I only added additional features and didn't touch any of the Linksys stuff) and you can easily put the original firmware if you don't like it or don't need more.

    There is no telnet or SSH access in the default firmware.

    = Jac

  • Linksys NAS200 2Bay SATA 2Port Network Attached Storage is not compatible with Windows 7

    Searching for answers, I found this: http://www.microsoft.com/windows/compatibility/Windows-7/en-us/Details.aspx?type=Hardware&p=Linksys%20NAS200%202Bay%20SATA%202Port%20Network%20Attached%20Storage&v=Linksys&uid=NAS200&l=en-US&pf=0&pi=5&c=Networking&sc=Network%20Attached%20Storage&os=32-bit

    Aparently this device is not compatible with Windows 7.

    I have one of those NASs with 2 SATA hard drives of 500 GB searched... I have all my music, movies, photos, and all of our backups of document on this device.  Because I have set up as a RAID array, I don't think I can remove the discs and put them in something to get my "stuff".  We used to use Win XP but recently upgraded both our machines to Win 7.

    If someone has been able to find a way to get to their stuff on one of those Linksys NAS200 devices without finding another WinXP machine somewhere?

    Hi Ken Mizell,

    If the device is not supported in Windows 7, you need to use a computer that is running Windows XP to move the data to a new storage device.

  • I have a disc in my Mac and can not understand about where to go read the content?

    I have a disc in my desktop iMac computer and can't figure out how to break through the buttons right or my computer to read the content of the program?

    Double-click the icon of the disk on the desktop. I hope that you have installed an application that can read the content for you.

    If you don't see the icon of the disk on the desktop, open the Finder, then go to the Finder menu bar and click Finder > Preferences, and then select the general tab and then make sure: CD, DVD and iPods is selected.

  • My MBP is showing a "Remote Disc" in the list of devices. It's not a hard drive.

    My MBP is showing a "Remote Disc" in the list of devices. It's not a hard drive. So where did it come from? I 'get info' on this subject, but it doesn't tell me a thing.  He sees the disk drives elsewhere in my house? It's to see my iPhone as a remote disc? The photo with him is a DVD or CD gold. It drives me crazy.  I am running OSX Sierra.

    This has been on the Mac for a while now... Here is a link that can better describe it.

    Use the CD or DVD drive from another computer with your Mac - Apple Support

  • Disc is stuck in drive iMac

    Eject and command-E do not cause the disc to eject from the drive.

    First option: reboot the Mac and hold down the mouse button while it starts. This should trigger the disc eject mechanism.

    If this fails, restart now Option button to get the start menu, and then press the keyboard's eject button.

  • How to use a blank disc DVD-R as a USB flash drive?

    Hi all! I'm running Mac OS X 10.9.5 on my MacBook Pro and I was wondering how I could use a blank DVD-R disc as a form of rewriting for documents, music, spreadsheets, etc. ? My mac Let's burn me to the disc, but I can't rewrite to it after that. Help, please!

    They don't work that way. Rewritable means simply you can erase the disc and use it again. You can't write it during normal use of the disk. This, to a USB flash drive.

    To be same rewritable, you can use a DVD - RW, DVD - r not it is not rewritable. You can look for third-party software that allow you to use the drive as a flash drive, but I am not sure that these programs exist. Not much need for it.

  • DVD Studio Pro DVD "supported disc not available".

    Hello Forum,

    I am trying to burn a DVD again an already existing DVD Studio, already registered and created the file pro with all the menus related to the video file.  Another company created the DVD Studio pro menu and queue in front of me, I replace the newly edited video and try to burn a DVD with the new video and audio files.

    I compressed the file Compressor 3.5 using the button create DVD in the compressor, I created a file DVD SD Mpeg2, audio and video.  Imported in the pro Studio already created DVD file, I have the burned DVD, but appears to "Support disc not available" when I try to play the DVD on my Imac drive (also not tried in a standard DVD player no chance)... I tried this twice now, the first time that I realized I had created a HD DVD, I also created a separate folder on the external drive as well.  When I click on the DVD that was burned it shows as: HVDVD_TS and no audio file.

    Can you please help me, I watched the video of youtube after another, but I'm not create from scratch, I know not at all unfortunately the program, but I use a DVD already created Studio, file with many menus already linked to the video and don't want to not recreate from scratch... I think this should not be so difficult, and definitely miss me something.

    Thank you very much for your help!

    -Tony

    Open the preferences of DVD Studio Pro and set it up to create the SD DVD.

    -DH

Maybe you are looking for

  • Cannot play video with 9.3.2

    I upgraded to OS 9.3.2 on my iPad mini and now I can't play video on Safari. What can I do?

  • Skype outgoing call is busy

    For the last 2 hours, whenever I'm trying to call my boyfriend he automatically says he is busy and the call ends, even if its status is online and he was not in a call to someone else. We all have two version 6.22.81.105 and prior to that with the v

  • TFncKy.exe repeatedly crashing in Windows XP

    Hi all I had a problem with the program TFncKy.exe since I bought my new Satellite M100 approximately a month or two ago. When I log on Windows, this program crashes before I press a key, and without worrying about know if I chose "Send report" or "d

  • Satellite A215 boots to BIOS password screen.

    I have a Satellite A215-7425 with a problem, I thought I'd pass along the forum. Thank God the three Toshiba laptops that we use, it's the only one who has this problem, so far. Spontaneously, this laptop starts with the screen of the BIOS at startup

  • ComBox MODBUS - difficult to write in the registers of the S.R.I.W.

    Hey guys,. I'm talking to a UPS (ComBox XW +) via MODBUS TCP. I can read the values of read only registers very well, and they line up exactly what I see on the interface of the web page they have. However, when I try to write a particular register r