Need advice on the best way to install win 7.

Similar Questions

• Need advice on the best way to set up a 6 nic Server

  I have a server with 6 cards.  Looking for some suggestions on the best way of provision.  We use the software iscsi client.

  Here's what I think to do:

  0/2 NIC (one onboard and a pci): VmNet

  1/3 network interface cards (one on board and a pci): vmkernel: vmotion/service console

  approx 4/5 (pci): vmkernel for software iscsi

  Is there a better way to do it?  It's just the way I'm used to doing.  It would be nice to maximize the number of ports used for iSCSI.

  Thank you!

  -shane

  Tough call...

  If you lose the management network, HA will cause a failover.

  If you lose the iSCSI, all virtual machines fail, but HA will not switch.

  If you lose VM network, all communications from the virtual computer fail, but HA does not tip over.

  If it was me, HA failover is a better option than full scall VM failure or net VM...

  But now, you will get twelve opinions on which is better.

  Dave Convery - VMware vExpert 2009

  ************************

  Accomplish the impossible only means that the boss will add it to your regular tasks.

  Doug Larson

• Need some advice on the best way to do specialized source distribution

  I need to give a customer a labview block, they can use our material in their own labview code that will read the (encrypted) data net senor off the coast and the flow of data in a form usable output.  I built a vi that can be used in a loop, a bit similar to the block of canned labview data acquisition that can be used to acquire data from products OR.

  There are many sophisticated (and secret) algorithms going on in the background which make sense data and translate them into a usable data table, but also configure the hardware itself. Accordingly the only final vi I prepared to distribute the client makes use of Subvi about 20. Almost none of these subvis could be ideally be reconverted in plain code in main vi, nor what I want to do this.

  The rules of the game is the following: I want to give him the block I created to use its own code, without him to see what's happening inside the vi.  I can deny him access to the block diagram/s, no problem, but I don't want to give him access to the subvis, to use, or even to know their names - preference they would be hidden or otherwise pre-compiled. Preferably I would just give him the main block only, perhaps with some support files that would be entirely opaque to him.

  Looking for advice on the best way to go. There is an elegant solution to this problem? For example, it would be better to compile the block as a .dll file, and then write a wrapper vi any?

  Have you thought of creating a packed library? You can also password protect your code. You can delete the distributed code block diagrams. You can use a combination of the above as well.

• What is the best way to install XP on Vista Equium A100-338

  I want to install XP on my Equium A100-338, who has already installed Vista. What is the best way to do it, I heard a lot of bad luck stories trying to do!
  I do it only as a new software, with that I need to work only works on XP.

  Any help appreciated

  Thank you

  Hello

  In my opinion, you must install the XP operating system on the second partition.
  In this case, you can use the two BONES; Vista and XP.

  Using these two s OS has many advantages. For example, you can always test the Vista and the new Microsoft features that are available in Vista and, in addition, you can use the XP if you need to run some programs and applications that are not fully compatible with Vista.

  Then first ask how o create a second partition in Vista.
  Well, this can be done in disk management. Right-click on the my computer drive management made right click on the disk to manage and modify the size of the partition.
  Then the free space on the HARD drive can be activated, and you can create the new partition.

  Then simply boot from Win XP and install it on the second free partition.
  The Toshiba drivers needed should be downloaded from the Toshiba page.

  Good luck

• What is the best way to install the new version--adobe always let things of the old version

  Hello

  I went through the installation of a new version, well... 8 times before. And I noticed that adobe has the bad habit of not properly uninstall previous versions...

  What is the best way to do it?

  Should I do an adobe install and regular confidence this time to remove completely the old version and its associated directories?

  Or should I uninstall the old version and install a new one? I was always afraid to go this route files bocause Organizer.

  Thanks for your comments.

  Because fortunately, most of the Adobe programs can coexist on the same computer, Adobe does NOT overwrite previous versions

  Now, if all uninstall completely from a previous installation, they would first use the uninstaller in Add/Remove programs. Then, a registry cleaner like CCleaner will take care of all that remains there. But wait, there is more!  For example, PrE, will NOT remove existing projects, which many people feel is a great thing. In addition, pre will not delete the preferences file, and this is why it is necessary to reset the preferences, if there are problems, even after repeated uninstalls / reinstalls. They can be removed manually. These two latter features security measures to protect users.

  Good luck

  Hunt

• Support for PIVOT query (or advice on the best way to do it)

  Hi gurus of SQL,.
  
  I'd appreciate any help you could provide on this request, I'm assuming that the best way to do this would be by using the PIVOT function. I read through some of the documents and books, and done some research here in the forums, but can't seem to find a way to make it work.
  
  I'm on Oracle 11.1.0.6.0 self.
  
  I have a table like this:
  

  ID     Product          Month_A_Amt Month_B_Amt Month_C_Amt     Month_D_Amt
  
  123     ProductA     3          5          7          9
  123     ProductB     2          4          6          8
  123     ProductC     10          11          12          13
  456     ProductA     1          2          3          4
  456     ProductB     3          4          5          6

  We get this data each month - Month_A is always the most recent month, and so it goes back for this game, Month_A is 09 November, Month_B is October 09, Month_C is Sept 09, etc. I'm OK with Hardcoding this value each month, so for the purposes of this exercise, just assume that Month_A is the 09 November, Month_B is Oct 09, Month_C is Sept 09 and Month_D is Aug 09.
  
  I need essentially "Pivot" in this table, so the end result looks like this:
  

  ID     Month          Product_A_Amt     Product_B_Amt     Product_C_Amt
  
  123     Nov 09          3          2          10
  123     Oct 09          5          4          11
  123     Sep 09          7          6          12
  123     Aug 09          9          8          13
  456     Nov 09          1          3          null
  456     Oct 09          2          4          null
  456     Sep 09          3          5          null
  456     Aug 09          4          6          null

  Here's the SQL code to create the database with test data table. Now that I've typed this explanation, it still seems easier that I had done it to be... but I'm still confused, so any help is greatly appreciated, thank you!
  
  create table test_base_table)
  Identification number,
  Product varchar2 (20).
  Number of Month_a_amt
  Number of Month_b_amt
  Number of Month_c_amt
  Number of Month_d_amt);
  
  insert into test_base_table values (123, "ProductA', 3, 5, 7, 9);
  insert into test_base_table values (123, "ProductB", 2, 4, 6, 8);
  insert into test_base_table values (123, "ProductC", 10, 11, 12, 13);
  insert into test_base_table values (456, 'ProductA", 1, 2, 3, 4);
  insert into test_base_table values (456, 'ProductB', 3, 4, 5, 6);
  
  Published by: TheBlakester on February 10, 2010 19:56

  Hello

  You don't want to make several clauses UNPIVOT and PIVOT; you want to do several sets of columns in a cluase PIVOT and UNPIVOT one clause.

  In the UNPIVOT clause, it's just a matter of replacing the unique "amt" column before the keyword FOR with a list in parentheses '(amt_1, amt_2)' and the replacement of each column in the list (for example, "month_a_amt") with a list of the same length ("(month_a_amt_1, month_a_amt_2)" ").
  In the PIVOT clause, it's just a matter of replacing the unique "SUM (amt)" aggregate function with a list of unparenthesized of functions, each with an alias ("the SUM (amt_1) AS amt_1, SUM (amt_2) AS amt_2'. The alias that will be added at the end of the givien for names output column in the IN clause.

  SELECT       id
  ,       TO_CHAR ( ADD_MONTHS ( TO_DATE ( 'Nov 2009'
                                          , 'Mon YYYY'
                            )
                        , month_num
                        )
              , 'Mon YYYY'
              )          AS month
  ,       product_a_amt_1
  ,       product_a_amt_2
  ,       product_b_amt_1
  ,       product_b_amt_2
  ,       product_c_amt_1
  ,       product_c_amt_2
  FROM       test_base_table
  UNPIVOT       ( (amt_1,         amt_2      )     FOR month_num IN (
           (month_a_amt_1, month_a_amt_2)     AS  0,
           (month_b_amt_1, month_b_amt_2)     AS -1,
           (month_c_amt_1, month_c_amt_2)     AS -3,
           (month_d_amt_1, month_d_amt_2)     AS -4              )
         )
  PIVOT       ( SUM (amt_1) AS amt_1
         , SUM (amt_2) AS amt_2 FOR product IN ( 'ProductA' AS product_a
                                                      , 'ProductB' AS product_b
                                     , 'ProductC' AS product_c
                                     )
         )
  ORDER BY  id
  ,            month_num     DESC
  ;
  

  Output:

  .              PRODUCT  PRODUCT  PRODUCT  PRODUCT  PRODUCT  PRODUCT
    ID MONTH    _A_AMT_1 _A_AMT_2 _B_AMT_1 _B_AMT_2 _C_AMT_1 _C_AMT_2
  ---- -------- -------- -------- -------- -------- -------- --------
   123 Nov 2009        3        9        2        9       10        9
   123 Oct 2009        5        9        4        9       11        9
   123 Aug 2009        7        9        6        9       12        9
   123 Jul 2009        9        9        8        9       13        9
   456 Nov 2009        1        9        3        9
   456 Oct 2009        2        9        4        9
   456 Aug 2009        3        9        5        9
   456 Jul 2009        4        9        6        9
  

  It looks like all the new values of amt2 are 9. Don't you think it's the best test? I think that different numbers, as you used for the examples of previous data, reduce the chances of getting good results purely by chance.

  If you want to experiment with queries like this, I suggest you use "SELECT *" (nothing added) in the SELECT clause. Start with just an UNPIVOT operation. Some examples in the documentation to do a TABLE CREATION AS... to save the results of an UNPIVOT operator and use this table as the base for a PIVOT table. I think it's a good idea to reduce confusion.

• NB550D - best way to install Win 7 64-bit and 64-bit drivers

  Hello

  I improved my NB550D to Windows7 Home Premium and installed 4 GB of RAM.
  This works much better, but want to go further and make a Windows7 Ultimate _64bit_ _clean install_ in order to take full advantage of theupgrade in RAM.

  My question is: what should I do about the Toshiba drivers for 64-bit? I guess I'm going to need some?

  What is the best way to go about the upgrade - any help will be appreciated! : D

  If you need to switch to Win 7 64 bit, then you need some Win 7 64 bit drivers.
  On the European driver Toshiba page, I could find some 64-bit drivers, but it seems that not all Toshiba for Win 7 64-bit tools are released.

  Drivers for WLan or BT stack can be found here:
  http://APS2.toshiba-tro.de/WLAN/
  http://APS2.toshiba-tro.de/Bluetooth/

  Other drivers or Toshiba tools such as value added package or Face Recognition, Eco utility and others could be used with other series of portable for example by Satellite C660D or others such as L750D, L755D or C670D
  Surely you must pay attention to the integrated graphics chip, the LAN or the chipset
  Use the drivers that are released for fleas in NB550D

• Best network design... Need advice on the best use of NIC

  I'm new to the concept of Distributed Switch so I need advice.

  Our current environment is the result of a vCenter 4.1 and ESXi 4.1 Enterprise Plus, but we are just using the standard vSwitch (1 for vMotion/Console and 1 for virtual machines).  When the distributed switch came out, we were warned that a vDSwitch could cause us problems if the server vCenter or database is down.  We could not connect directly to the host and make network changes because the vDSwitch is set in the database.  That's why we stayed with the Standard vSwitch only.

  Our farm is quite small, only 5 hosts but we run around 100 mV in this regard.

  We use currently servers HP DL385 G7, which have 4 cards integrated network, and we have a map of installed NETWORK 4 port card.

  I use the NETWORK 4 EtherChannel ports and trunk card to our virtual machines.

  I am currently using only 1 network card integrated for vMotion and 1 for the Service Console and they all have two of the other defined as secondary.

  This configuration has worked very well for us, but I realize that the latest version of ESXi has some new features that we could use.

  NEW CONFIGURATION

  I'll put up a new vCenter 5 and ESXi 5 environment and I am considering using the switch distributed instead of the usual vSwitch we use.  I'm also eager to take advantage of the multiple NIC vMotion.  All our cards are 10/100/1000 MB capable... No. 10 GigE.

  I think... use that map 4 NETWORK ports for my EtherChannel/trunk for just as our virtual machine before, but this would be set to vDSwitch1

  The mixture of my 4 other integrated ports, it's causing me grief.  Should they be on a standard vSwitch or vDSwitch?  Use 2 ports for vMotion and 2 for the Console?  I really thought to use 3 ports for vMotion and 1 Console port.  I could put the Console port to use one of the vMotion ports such as adapter of standby is... I'm so confused freaking!

  Any recommendations on how I should put up?

  Hello

  Given that you can't split your vmnic for each vSwitch I would recommend either keep configuration simular with the knoweldge if a whole nic fails, you will take a failure or as autumn has already been mentioned on 'Origin Port ID'. Lets do this out and give a little better example

  Current configuration

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  vSwitch1

  VMNIC4 - extension PCI NIC - Etherchannel trunk - PortGroup - VMNET

  Extension VMNIC5 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC6 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC7 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Now, to captured to eliminate any single point of failure that you could do is break your Etherchannel trunk and back this vSwitch from Port ID and Setup VMNIC2, VMNIC3, VMNIC4, VMNIC5 as vSwitch1 for your VMNET. Then the cable to multiple switches eliminate any single point of faiulre. If your standard configuration would look like this

  vSwitch0

  VMNIC0 - on - Board Service Console

  VMNIC1 - Board - Vmotion

  VMNIC6 - extension PCI NIC - Vmotion

  VMNIC7 - extension PCI NIC - Vmotion (standby Service Console)

  vSwitch1

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  So to finish any request for psyhical nics on this particular configuration the Port ID of origin essentially around robins. If during your first VM is online it will be use VMNIC2 and nic forever, until a failure, in which case he will grab the next nic online. When your second VM is online it will use VMNIC3 forever, until a failure and so on. This still will give you around the same way through to as far as networking is concerned. However if you are attached to the trunk, etherchannel 4 GB and can obsorb a failure in case of failure, the network card 4 ports can stay.

  Distributed switching Setup

  Allows you to see how you can switch to distributed switching

  Let's start first of all, you can have EVERYTHING in switches distributed even the service console port if you wish. The resason why some people do not like to do this with the service console port is because IF your database is broken you cannot make any changes to the distributed switch. However it will not prevent a feature to your distributed it switches simply means, you can change them. Also if just getting worse and your DB has been declining for some time and you REALLY need to make a change to the service console port you can go into the console and change back to a standard vSwitch if need be. This allows the said look at some standard configs, you can work

  vSwitch0 (Standard)

  VMNIC0 - Service Console Port (Port Original ID or standby)

  VMNIC4 - Service Console Port (Port Original ID or standby)

  vSwitch1 (Standard)

  VMNIC1 - Vmotion

  VMNIC5 - Vmotion

  Distributed switch

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Now this config using originating port ID and breaks your etherchannel if you want to keep your configuration with the etherchannel it can look like this

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  Distributed switch

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Other changes to the configuration may also put the vmotion in distributed witch the VMNET but you would to VLAN, or you could create a second Distributed switch and put it as long as there are 2 network cards. It can go either way. The main advantage of a distributed switch is that it brings all of your settings with you in any host. So trade ect all your VIRTUAL networks is really easy to reproduce if a new host is brought online, all you have to do is to add the new host network cards in the distributed switch and your config is done. With that in mind lets look at the service console. This console is always configured on EACH Setup program that out you of the box if not that you really need to have these parameters transported on several hosts that is another reason why most people just don't. VMotion is up to you, I have seen and configured two ways, it all depends on how simple you want to keep it or think of switching / vlaning / port of groups.

  If you have any questions please let me know, I hope this has helped

• What is the best way to install windows 7 on 3 computers at home, all Macs with no previous version installed?

  I intend to divide my drive hard while I have both a mac and pc side to get the best of both worlds, but I'm not sure what product would be best suited. As I said previously is for 3 computers that don't have currently no version of windows on them, so I guess the family upgrade would be of no use and I'm not sure whether a House package might be installed on all 3?

  The most cost-effective option in your case is to buy copies of Windows 7 Home Premium System Builder. You will always have to spend money, but against the full package of Windows 7 Home Premium retail, its more profitable:

  Price OEM new eggs:
  Windows 7 Home Premium 32-bit: http://www.newegg.com/Product/Product.aspx?Item=N82E16832116752
  Windows 7 Home Premium 64-bit: http://www.newegg.com/Product/Product.aspx?Item=N82E16832116754

  The OEM of Windows 7 versions are identical to the versions commercial full license with the following exception:

  -OEM versions don't offer any free direct support from Microsoft technical support Microsoft

  -OEM Licenses are tied to the computer first you install and activate it on

  -OEM versions allow all hardware upgrades except for an upgrade to a different model motherboard

  -OEM versions does not switch directly from a former Windows Andre Da Costa http://adacosta.spaces.live.com http://www.activewin.com operating system

• Give advice on the best way to create tables

  Hello

  I'm just after the best method to create a pdf document that got charts?

  I have an order form which must be converted to an editable pdf form that users can fill in electronically and email back. Currently, the document is in Excel, and while I can convert it to PDF, I prefer to create the whole thing using the PDF.

  Should what tools I use for this?

  Kind regards

  Peter

  PDF files should not be created from scratch and if you try to do you will soon discover that it is extremely difficult and heavy.

  Stick with the creation of the file in Excel (or any other similar application, such as Word, InDesign, etc.) and then convert to PDF and add form fields in Acrobat.

  Be sure to keep a copy of the Excel file, well, in case you need to make any changes to the layout of the file later.

  If you don't do this then you can order replace Pages use in Acrobat to insert new pages (static) on the 'old' in your PDF file, that will keep all the form fields and scripts of tact. You need to just adjust the locations or the size of the fields, where this is necessary.

• What is the best way to install photoshop on multiple devices?

  I am considering the classes of photoshop running for a small group of 10 people say, a month. Is it possible to install photoshop on ten machines for a single month, or what would be the best course of action in this scenario?

  You can call Adobe. They have only $10 a month for teaches and students face.  Maybe they have special offers for schools which do not have classes throughout the year.

• Advice on the best way to transfer information from the old laptop again.

  Please could you offer me advice, I bought a new laptop and want to transfer everything from to the old laptop, any advice would be grateful. Thank you James

  Please could you offer me advice, I bought a new laptop and want to transfer everything from to the old laptop, any advice would be grateful. Thank you James

  Transfer files and settings from another computer
  (This is a web link, click on it.  There is even a video.)

  PS - you install your applications (office suites, alternative web browsers, customers of messaging, plugins, games, etc) manually using the installation media and you SHOULD do before using the Windows Easy Transfer Wizard.

• The best way to install Windows 7, so I can run on my MBP el Capitan end 2011 calyx Point Software?

  How to install Windows 7 so I can run on my MBP el Capitan end 2011 calyx Point Software?

  Please start the Windows installation using Boot Camp - Apple Support .

  The following links should also be useful.

  Install Windows 7 and earlier Apple Support on your Mac using Boot Camp -

  https://help.Apple.com/Bootcamp/Assistant/6.0/

• The best way to INSTALL my downloaded purchase of Lightroom 5 standalone (NON-CreativeCloud) on my Macbook Pro OSX 10.9.5?

  So I just download my purchase of 5 of Photoshop Lightroom. I bought it via the Adobe.com site and this is the full desktop version, standalone version of the software.

  Important FYI:  Please note that I bought the not-CC Lr program to download.

  Question : How I INSTALL it after you download it on my Macbook Pro using OSX (latest version of Mavericks 10.9.5)?

  I cannot find the Setup instructions for Lr CC and mobile, but not for the full, non - CC licensed desktop version which is what I have!

  Perhaps the above, is that the same step by step installation process as my Lr said 5 but why Adobe doesn't' t say anywhere where I could find.

  Any help?

  T.I.A.!

  
  

  PS FWIW, I especially request because I'm just afraid to spoil something, or install it wrong or wrong place; I want to make sure I do it correctly so not to damage the plant or whatever, even though I'm pretty sure I know how. Double control system for my own confidences/mental health...

  Download the last lr and installation using your serial number,

  Downloads available:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
  • Acrobat: XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7
  • Lightroom: 5.6| 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5
  • Contribute: CS5 | CS4, CS3

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Need advice on the best distort tool to use.

  Hi people,

  I started working on a picture of the man-in-a light bulb as shown below. All OK so far except when I try to make the fingers look more as they are pressed against a curved surface.

  I used the spherize filter on the layer of human and general transform/warp, but still can't put the right hand.

  Here is image as it is so far.

  Any advice greatly received.

  See you soon,.

  Eugene.

  (PS - CS5 version 12.0.4 x 32)

  

  Have you tried puppet Warp (on a Smart Object, naturally) yet?

  Move the filter may be another option.