need help in my network ip foscam Androida conncet my IE firefox account

How can I conncet my Androida network for my ip Foscam camera
F18904w.

I'm not sure what you're asking help with.

If you try to use some kind of video camera IP with Firefox, it may not work if the device requires Adobe Flash to provide the video signal.

Tags: Firefox App

Similar Questions

  • Need help setting up network home (Windows 7 Professional)

    I don't know why I have so much trouble with this.  I think that I never properly put in place a network before.  Usually, I just turn on my router with a password, and then the phone and other devices connect directly to the router.  I just got a new computer with Windows 7 Professional and it is prompting me to create a home network - and have apparently created a new password for the 'network' that is different from the password for the router.  I have a feeling that this will be easy, but I do not get set up correctly.

    First question, in the instructions to configure the network at a time given, was asked if all "clients" had a "wifi protected setup" button

    What is a 'client' on the network?  My router Linksys has one of these buttons (I pushed him, but he could not get connect/setting up with Windows 7).  Is a router from a client?  If so, a client what?  (I do not understand the use of the term client.)

    Here's what I would do.  I have internet entering a cable modem.  Ethernet to the modem router Linksys WRT54G.  (I don't remember the exact model.  It has a button "wifi protection setup.  Ethernet to the router to the desktop.  The router's Ethernet compatible HP printer wifi (which is currently on its own network).  The Windows account has two users (mine, of my wife).  The goal is to have a single network, with the office and the connected printer, and who I can connect with my iPhone.  And I want to be able to print wireless from my iPhone to the printer.

    Here's what I did.  There is a lot of information, but if all goes well it will prevent additional questions.

    I have reset the router and went to the 192.168.1.1. page.  In the Administration tab, I created a new password - which I thought was the password for the network.  I was not the case.  In the wifi tab, I looked for a place to put a password, but could not find one.

    I went on the computer, the network options in Control Panel to add a new network.  I was able to get a new network with the computer (LAN) connected to the router, but I couldn't get wifi to set up.  He told me to press the setting button of protection wifi on the router, but after a long delay, he said that he could not establish a connection.  Finally, I got a message (I don't know how) if I wanted to connect older devices to the network, I need to put a code - 12 letters/numbers with dashes.  I don't know what types of devices called it.  So, I found in managing network a "network key" tab  It was the same code - and it also seemed to work as wifi password.  But I can't change it to something that is possible to remember.

    And I can't do the printer on the same network as the computer.

    I guess I'm going something wrong.  Can someone point me in the right direction?

    It seems that if the printer is in 'ad hoc wireless' mode - it is just sitting there with his wi - fi enabled: indeed, 'here I am; connect to me if you want to print. »

    You need to connect the printer to the network wireless router.  It's pretty easy, but if you want a specific rather than general instructions, please provide the exact model of your HP printer.

    Generically, see--> http://www8.hp.com/us/en/campaigns/wireless-printing-center/printer-setup-help.html , you will probably end by using the option of 3rd or 4th.  In step 4 of the "HP Wireless Assistant', 'the WEP key or a WPA password' is the 'wifi password on the router" - which really, you must configure except if the House really is miles from any other civilization.

    "Referring to the first paragraph above, what I called the mode"ad hoc"seems to be what HP calls impression of"peer-to-peer"."  More specifically, in the FAQ at this link, your printer seems to currently be configured as described in "how to print wireless without a wireless router?

    Although he adds a little more complexity, I highly recommend that - after that you get things market - you read the FAQ section of HP on "a static IP will keep my computer against the loss of communication with my printer wireless."  In an environment with multiple wi - fi devices (for example, several iPhones), if the printer is turned off for a while, when you turn it back on it you will find that your computer will display is no longer her.  Print jobs will appear to work, but nothing will print.  If this situation arises, the solution is this FAQ section.

  • Need help setting up network RV180

    Hello

    We have an active service test/repair devices IP Center. A simple test of PC application communicates with devices via UDP packets. I need to configure my test intranet envirement exactly as production. My problem is that I can't solve my network addressing. Note: IP configuartion peripheral Test should not be changed, the test application must be able to ping 10.90.206.34

    * Host PC *.

    IP 192.168.60.86

    subnet 255.255.255.0

    * Test device * (cannot be changed)

    IP 10.90.206.34

    subnet 255.255.255.240

    Gateway 10.90.206.33

    Can anyone recommend how I can us a RV180 (or several) to solve my problem?

    See you soon

    Steve

    Steve,

    Excellent happy you guessed it work.

    First thing that strikes the second problem is that it is another subnet. Why don't you just create a new vlan on the router. You can have 4 VLANS on routers. You can have them both going at once then. You can also consider opening a new thread on the new problem.

    Thank you

    Tony

  • Need help to remove unsightly bar from the top of my Firefox. May need to change the userchrome

    So my Firefox used to look like this http://i.imgur.com/u7wWT.jpg (ignore the WaterFox bit, it's an old picture I switched to Firefox since then and had the same layout)

    It's about as effectively as possible in order to maximize the screen space, which, on my 1280 x 1024 screen, is very valuable. Then they took the addonbar. I found an add-on to bring it back, who worked little...

    http://i.imgur.com/BQw2n3X.jpg

    Except for two things. First, the pale blue bar at the top. A remnant from which the URL bar has been so stupidly front. Can't get rid of it in the Customize menu.
    Secondly, I can't get the back + next button on my addonbar more. I have a menu drop down it with the buttons on the inside, but it's a little less convenient. There is no other forward/backward buttons in the Customize menu.

    Any help would be greatly appreciated. Thank you for your time

    Have you checked the Options/preferences of the extension of the RTC, which has a parameter for mobile buttons previous and next among its settings?

  • Need help with network home using Airport extreme

    I need help with my home network.  I'm not very aware when it comes to all things network.  Here's how my network is currently set up.

    Cable modem to Airport Extreme for Gigabit Switch.  Cables come out of the switch to all areas of the House.  I have 2 other extreme airport connected in other rooms of the House directly on the wall that dates back to the switch.  I hope I am explaining that properly.

    My problem is that this seems to have caused some of my connections cable does not work.  When everything is configured, it has worked well.  All connections in the House worked.  Then we have disconnected one of the extreme airport and moved to another location in the House to have the best wifi coverage.  Since that time, a lot of the ethernet wall plugs are not working.  For example, when I plug in my Macbook Pro in making ethernet in my kitchen, it says connected but it has an assigned ip address and cannot connect to the internet.

    Any help you can provide would be great.

    I would like to get the return tech to help you to...

    But it is likely that something (or someone) has tampered with the settings.

    The layout is fine... but you can cause problems with the network by creating a loop.

    This can happen because the AE you moved is connected wrongly... somewhere in the network it is connected to the switch again.

    Or AE is set to expand wireless... It's FAKE... It will loop the network on the back main EI wireless.

    Unplug the two AE you have that function as extensions...

    Turning off everything else... then it works again...

    Do it in this order.

    Modem... Wait 2 min

    AE... Wait 2 min

    Switch.

    Now check that the network is working properly... power of customers in various locations and make sure everything is good.

    If so, then manually reset the two AE of factory and redo their installation.

  • Windows 7 - need help to install Microsoft Network Version 2.0 Framework 64-bit

    I need help, I had someone install Windows 7 Ultimate on my laptop.  I have the 64 bit version, I read some of the other forums and I Framework 3.5.1 installed, and I get a message each time I log on that says "Microsoft Network Version 2.0 Framework" is needed to continue. I tried to get it in the downloads of Microsoft, but I get SO many results that I don't know which one I need. I could not use my wireless, wireless printer, I have Windows 7.

    You may wish to review the previous discussions on this topic: Http://www.google.com/search?hl=en&safe=off&rls=com.microsoft: en - US & q = + site: social.answers.microsoft.com and .net framework 2.0 + required + continues & his = X & ei = qNouTI2hDsH_lgfV8cWSCg & ved = 0CBkQrQIwAA ~ Robear Dyer (PA Bear) ~ MS MVP(c'estàdire,messagerie, sécurité,Windows&UpdateServices) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • NEED HELP WITH SERVICE PACK 3. After downloading and the computer goes into rebooting mode I get the screen to restart with three options, network security safe mode and the other thing. ,

    NEED HELP WITH SERVICE PACK 3.  After downloading and the computer goes into rebooting mode I get the screen to restart with three options, network security safe mode and the other thing. , but it of although he gets, he keeps countdown to restart and reboots and restarts, over and over again, never reboots, same screen. my computer won't let me out this screen even after I turned off the computer and turn it back on, I get the same screen. the only way I can get out of this is to erase my computer everything and bring it back to factory, right out of the box, this big headaches. Thanks for anyone who can help me. PS. Keep the answers in simple terms please.

    Hi BSRC$, in stock

    1. You have security software installed on the computer?
    2. You receive an error message when you restart the computer?

    Reinstalling Windows XP to the factory setting would not be the first option.

    It is possible that some third-party programs or the services installed on the computer interfere with the installation of service pack 3.

    I suggest that you try to uninstall service pack 3 from the computer by using the recovery console and subsequently ask the article below for what to do before installing the service pack 3on the computer.

    How to remove Windows XP Service Pack 3 from your computer

    http://support.Microsoft.com/kb/950249

    Steps to take before you install Windows XP Service Pack 3

    http://support.Microsoft.com/kb/950717

  • Need help Kodak 5500 AiO printer over the network.

    I have a kodak 5500 AiO printer. I have vista on all my computers (1 bureau and 3 laptops). I downloaded the sp2 for vista on all computers, after I downloaded sp2 desktop mouse and keyboard froze, I had to uninstall sp2 to make it work. Now the printer on my home network to print or not be discovered by my laptop. I can see the printer on the network to my laptop but I can't connect to it. The printer is on the desktop via a usb cable. I deleted the printer drivers and reinstalled and downloaded the software and drivers for the latest printer.  I need help.

    Thank you

    Phil

    original title: using network printer

    Everyone,

    That's what I had to do to get my printer working once Vista it has messed up. You do the first two steps on the computer to which the printer is connected. The last step that you do for your laptop or you want to connect the printer to the main computer. I hope this helps.

    Hey all,.

    We had this same problem...

    We had to follow the procedure proposed by Drompa...

    > 1) share permissions
    >> 1. In explorer, select C:\windows\system32\spool\PRINTERS
    >> 2. Make a right click, properties
    >> 3. Tab sharing
    >> 4. Advanced sharing
    >> 5. Check "share this folder".
    >> 6. Permissions
    >> 7. Grant everyone full control
    >>
    (> NTFS permissions 2)
    >> 1. In explorer, select C:\windows\system32\spool\printers
    >> 2. Make a right click, properties
    >> 3. Security tab
    >> 4. Edit
    >> 5. Add
    >> 6. Advanced
    >> 7. Find now
    >> 8. Select 'NETWORK '.
    >> 9. Ok
    > 10. Total control of the NETWORK grant

    AND THEN we had to install local printers, using the port trick...

    1. go to 'printers '.
    2. click on "add a printer".
    3 Add a local printer.
    4. "create a new Port.
    5. use the "Local Port" option
    6. on "Enter a Port name" enter: "\\Computername\Printername".

    And if all goes well should do!

    Good luck!

    Credit to Drompa and otherdreams to help out me.

    Phil

  • I need help setting up my home network - windows vista.

    I need help to configure my network, I ave a laptop & hubby the computer w / dsl wireless rouuter. If I can get trhis to work, maybe we can work on the printer.

    Original title: help w / home network

    Hi Luvy,

    Thanks for posting your query in the Microsoft Community Forums!

    Looks like you need information to set up home networking on the windows vista computer.

    We're here to help and guide you in the right direction.

    -What is the number of brand and model of the computer?

    I suggest you to return the items online help and check if it helps.

    Setting up a network home

    http://Windows.Microsoft.com/en-in/Windows-Vista/setting-up-a-home-network

    Setting up a wireless network

    http://Windows.Microsoft.com/en-in/Windows-Vista/setting-up-a-wireless-network

    To install the printer on the network see Help below articles.

    Install a printer on a home network

    http://Windows.Microsoft.com/en-in/Windows-Vista/install-a-printer-on-a-home-network

     

    Share a printer

    http://Windows.Microsoft.com/en-in/Windows-Vista/share-a-printer

    It will be useful.

    Let us know if you encounter problems under windows in the future. We will be happy to help you.

  • Need help to install the network on laptop drivers

    I have a laptop of HP 2000-239WM and recently erased due to trying to sell. However, when I reinstalled everything back on the PC, no network drivers have been installed, so I have no access to the internet, wireless and wired. Should what programs I install via USB in order to solve this problem?

    The network adapter driver specifically requests the Ethernet, wifi and it...

    Hello McKinley,

    Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

    According to the description, I understand that you need help to install the network drivers into the laptop.

    Certainly, I understand your concern and will try my best to help you.

    In order to install the NIC drivers in the system, I suggest to visit the link below and check if that helps.

    http://support.HP.com/us-en/drivers/selfservice/HP-2000-200-notebook-PC-series/5091493/model/5119030

    Note: Make sure you have access to the internet to another computer and download the network drivers using the USB and install on your laptop.

    I hope this information is useful.

    Please let us know if you need more help, we will be happy to help you.

    Thank you.

  • RVS4000 private networking, establishment of local networks virtual need help!

    Hello

    I live in a two family dwelling house and we share a common Internet fiber connection. In the basement, we have a modem/router (zyxel) which is in mode "bridge."  Therefore, only not as DHCP.

    Behind this zyxel, we have a Cisco RVS4000 router. Ports 1 and 2 go to the family, and the Ports 3 and 4 go to the B family.

    Family A and B have separate routers which are both set to "access point mode. Family has a router ASUS RT-N66U, whereas family B has a dlink DIR-615. The asus has a point "access" mode, while the dlink must be configured manually to achieve this goal. The dlink must also have a static IP address. The asus can receive the ip address.

    I have tried without success to reach and beg currently to get help are separate networks for the two families can access Internet, but at the same time, it must be impossible to access VLAN1(Family A) from VLAN2(Family B) vice versa. Which means no communication between the two families through the local network.

    I tried different options but I don't know how to deal with the trunk, tag, no tagged etc etc etc. It seems every time that I managed to create two different networks there is accessability/communication between two VLANs, and whenever I managed to give different IP addresses for different ports, i.e. 192.168.10.xx and 192.168.2.xx it is always possible to communicate. What is also happening usually, it's that the Internet is interrupted at the same time.

    -What someone would be kind enough to help out me? Since I'm quite not seasoned networking, I need a detailed guide indicating all the actions that I take. If possible also with illustrations.

    Any help will be much appreciated.

    Hi Andreas, there is no need to configure any trunks or tag all traffic for what you are trying to reach.  Circuits and the marking would be only required if family a (VLAN 1) or B (VLan 2) of the family set up the additional VLANs on their access points.  Lets say VLan1 of family and the family then wants a Setup VLan 3 and 4 of VLANs on their AP, then you would need to set the line going to the family as trunk and label all traffic.  If A family uses only 1 VLan, then it is useless to set up as a trunk line.

    I want to suggest to configure all 4 ports of the router as "Untagged" and disable routing between Vlan1 and Vlan2 InterVLan.  This should do what you're trying to do.

  • Need help to understand the network of vSphere environment

    Hello

    I need your help in understanding the network environment in vSphere. Please see the diagram and the text below:

    vm.png

    NIC #1 - Management Port (access from client vsphere, vCenter server)

    NIC #2 - Port of VMkernal (for iSCSI, vMotion, etc.)

    NIC #3 -?

    #4 – CARTE NETWORK INTERFACE?

    Q1 how allow external users to access services over the ESX host? (for example, IIS, FTP, Exchange, NFS)

    Q2, what will be the role of the other two network cards? Is it connected to the physical switch?

    * Ask you all to please help me by sharing your knowledge / experience on the network portion, you have made in your environment as NIC how, what to do with that. *

    I really need to understand the networking of concepts in vSphere, hope that your help!


    Best regards: Yash

    With an additional NIC with 2 port a general configuration might look like this:

    vSwitch0 - vmnic0, vmnic1 (connected to different physical switches)

    Network VMkernel management

    VMotion VMkernel network (own IP network, own VLAN)

    Better if they is configured as active / standby.

    vSwitch1 - vmnic2, vmnic3 (connected to different physical switches)

    Trade VM

    vSwitch2 - vmnic4, vmnic5 (connected to different physical switches)

    VMkernel iSCSI (own IP network, own VLAN)

    Ideal if it is added to the component Multipath iSCSI, which is quite easy to vSphere 5.

  • Need help with the data storage store, local array and network connections

    Need help with my ESXi 4.1 installation

    My hardware:

    I built a server with an Asus P6T whitebox, i7 920, 12 Gig RAM, NIC, Intel Pro1000 PT Quad, 3ware 9650SE-12ML with 8 1.5 TB SATA green in a raid 6 array gives me about 8 + TB with a spare drive all housed within a NORCO RPC-4220 4U Rackmount Server chassis.  I also have a 500 GB SATA drive which will hold the ESXi and virtual machines.

    The network includes a firewall, Netgear Prosafe FVS336G, GS724Tv of Netgear ProSafe 24 port Gigabit Managed Switch on a dhcp cable modem internet service provider.

    I also have 2 old NetGear SC101T NAS disks (4to) I want to connect to the system how some - at a later date have... data on them and want to transfer to the new storage array. I always looking into the question of whether they will work with ESXi 4.1, or I might have to only access it through Windows XP.

    My Situation:

    I have already installed ESXi 4.1 and vsphere client with no problems and it is connected to a dhcp cable internet service.  I've set up host via a dynamic DNS service name give me a static hostname on the internet.  I installed three machines to virtual OS successfully at the moment and now want to first start by creating a multimedia storage server which will use some of this new 8 TB array, then separate data storage for use with a web server small overhead storage and a backup.  It is a domestic installation.

    Help with the data store and network:

    I was doing some reading, because I'm new to this, and it looks like I'll probably want to set up my table via ESXi as a nfs disk format.  Now, the data store is usually in another physical box from what I understand, but I put my readers and ESXi all in the same box.  I'm not sure that the best way to put in place with grouped network cards, but I want to make this work.

    I understand that in ESXi 4.1 using iSCSi LUN must be less than 2 TB, but nfs - I should be able to add a bigger partition then 2 TB (for my multimedia) in nfs, right? or should I still add it separately as a separate 2 TB drives and then extend them to get the biggest space.

    Any suggestions or direct resources showing examples on how to actually add some parts of the table as data warehouses separate nfs.  I know that to go to the configuration tab, and then select Add to storage, and then select nfs. I have not my picture, but it's here that I don't know what to do because ESXi 4.1 system already has an address, should I put the same thing to the new data store array also (will it work?), and what should I use for the name of the folder and the store of data... just do something to the top.  I thought to later install Openfiler (for a multimedia storage using this table server) as a virtual machine, use the table with esxi so that I can access the same storage space with widows and linux-based systems.

    I also know I have to find a way to better use my quad nic card... put in place of virtual switches, grouping, etc HELP?

    Any direction, assistance, similar facilities to sample, suggestions or resources that would help would be great. I did a lot of hunting, but still a little confused on how to best to put in place.

    You must think of VMDK files of large databases with records of random size guest go read some data (a DLL or an INI file), maybe write some data back, then go read other data. Some files are tiny, but certain DLLs are several megabytes. It's random i/o all and heavy on the search time. IO Opsys is small random operations that are often sequential (go read data, write data, go read other data,...) so that deadlines are critical to the overall performance. That's why people say OPS are / s of reference and forget the MBs flow. The only time where you bulk transfers are when you read media (ISO files).

    Well, now forget all this. Actually the disk activity will depend on the specific applications (database? mail server? machines compiler?), but the above is true for boots, and whenever applications are idle. You should see the profile to know.

    RAID 10 is faster (and often more reliable) than RAID 5 or RAID-6 except in certain specific cases. In General RAID 10 is ideal for many random writes, since the calculation of parity for RAID-5 and - 6 adds to the overall latency between command and response - latency is cumulative if a little slow here and a little slow it adds up to a lot of overall slow synchronous especially with e/s on a network. OTOH RAID-5 and -6 can produce faster readings due to the number of heads, so you can use it for virtual machines that transfer bulk. Test. You may find that you need several different types subdashboards for best results.

    You said 3ware, they have some good grades on their site, but don't believe it. With my 9650 that I found myself with only a couple of their recommendations-, I put the (simple) table for allocation size 256 k, nr_requests at 2 x the queue_depth and use the planner date limit. I had the habit for the Ext4 file system formatted with stride and stripe-width synced to the table and used the options large_files with fewer inodes (do not use the huge_files option unless you plan to have single VMDK files in the terabyte range). Use a cache of great reading in advance.

    Virtual machines use VMDK files in all cases except raw iSCSI LUN that they treat native disks. VMDK is easier to manage - you can make a backup by copying the file, you can move it to a PC and load it into another flavour of VMware, etc. There could be some features iSCSI to your San as a transparent migration but nothing for me. NFS has less chatter of Protocol if latency lower times to complete an operation. NFS is good to read and write a block of data, that's all it boils down to.

    UPS is good, but it won't help if something inside the machine explodes (UPS does nothing if the PC power supply goes down). If the RAID card has an option for a battery backup module, so it can contain some writings in memory and may end up the disk i/o after replacing the power supply. 3ware also limits the types of caching available if help is not installed, and you get just the right numbers with the module.

  • Need help networking Lab Manager

    Hello

    I'm having some problems with the implementation of a closed network and to be able to access the external environment of the fence.

    We have a production environment that I cloned for use for testing and development, so we have to our QA and Dev staff to be able to RDP to the virtual machine and to be able to run scripts from their PC in the environment of LM.

    The implementation of models and the creation of the configurations are made and the VM can all see each other on their internal network. All IP addresses are exactly the same, as they are in the production network (IP address of 192.168.11.xx).

    I created a network physical and fenced (192.168.208.xx IP address) by using the static method - Pool of IP and static manual Options, set the default gateway of 192.168.208.1 and linked to a virtual switch on the host computer that is connected to one of our basic physical switches. The port, we connect uplink to switch, is in it's own VLAN and has the IP address of 192.168.208.1 and allow us the IP to the DEV, QA VLAN but not the vlan production by using access lists.

    When I deploy the configuration, network fencing itself and I can see the virtual router using the VI client, however, I cannot ping the addresses or RDP at all on 192.168.208.xx LM Beach assigns to the configuration of the VM. The virtual machine inside the configuration, however, can ping those addresses natted (as well as internal addresses).

    I managed to connect to the virtual router and I noticed that the 2 interfaces are both on the 192.168.208.xx network. We shouldn't be on the internal range of configuration (192.168.11.xx) in order to make routing / natting correctly? What do we lack?

    When close you a physical network, the vRouter resumes the internal address of the physical network IP pool. When you connect a virtual network to a physical network, the vRouter returns to the internal address of the virtual network IP pool.

    It seems to me that your virtual machines were given to the 192.168.11.xx with manual option static, right? In this case, the router will again resume an internal address from the pool of the physical network (think about it, where else would he get all this?). Your needs, create a virtual network with a range of IP addresses in the 192.168.11.xx address space as there are enough IPs for all the virtual machines in your configuration and an additional IP for the internal NIC. of the vRouter use the option "Connection networks to physical virtual networks" while deploying.

    This might help:

    http://communities.VMware.com/thread/250657

  • hp2544 need help on the installation of the first.

    I just buy a 2544 I bought it because of the impression of ipdad capabilities.

    The thing is that I have also recommended my sister bought one and it does not have a laptop or PC. She lives 100 miles so sharing mine is not an option. She bought his first and he's now sitting in the waiting area for me to tell how to install it on its network. She has a hub of sky.

    I searched and can't find any instructions can anyone help please?

    Hi spanisheyes.

    Welcome to the HP Forums!

    I understand that you need help setting up your HP Deskjet 2544 to your iPad, and I'm happy to help with this problem!

    Please take a look through these two guides:

    Hope this helps, and hope to hear from you!

Maybe you are looking for

  • Since the upgrade to iOS 9.3 my iPhone 6 says no service.

    Since upgrading to iOS 9.3 I have no service. How can I fix it?

  • How to clean the cooling module? (Satellite SA60)

    Hello worldI have a big problem on my cmp.it is very hot in no time. I think that his condition is not good enough and during the COP/MOP purchased slow.i be hot all my work will this cmp 1 year ago and I did not own inside my cmp.is it necessary to

  • mmhk taken by mistake

    In recent days I constantly receive a 'Safari quit unexpectedly when you use the plug-in mmhk.»  Click to open the application.  This report will be sent to Apple. » What is the cause and how to fix it? Thank you

  • Pavilion E018TX: I forgot my BIOS password

    Hello I forget my BIOS password. Previously, BIOS Locked by asking the password and at that time, I used the default password as 47141111 and I entered the BIOS. I changed the Pwd right there and I forgot now. I also tried with BIOS default Pwd 47141

  • Impossible to uninstall cam Cyberlink U 5, error: 1158.

    Original title: uninstallation problem I have installed Cyberlink Cam 5 u. It s not working do not. I want to uninstall but it s is not possible. (The error message comes 1158) How to uninstall this software? It s creating a problem when using system