Need help to configure the VLAN on a powerconnect 5448

Similar Questions

• Need help with configuration of VLAN SF300-24

  Hello

  Let me Preface this with the fact that networking is certainly not my point hard, so here, any help is greatly appreciated.

  I'm trying to segment on a virtual desktop on its own VIRTUAL local network infrastructure using a Cisco SF300-24 Layer 3 switch. I can get the switch to connect to the network with the assigned VLAN 1 an IP address on the subnet of the network (192.168.16.X), but I can't get anything this is set up VLAN 20 (192.168.20.X subnet) to connect past the VLAN 20 (192.168.20.254) gateway IP. The ports assigned to 20 VLAN are defined to access the mode if it matters.

  Here is a diagram to illustrate what it looks like, as there is another (L2) switch involved.

  

  So I'm not really sure what I am missing here since all settings seem simple enough.

  Hi Simon, I recommend you remove any server active directory and essentially remove all safety factors. This will give the idea of where to start.

  If you take a quite basic set, 2 Windows 7 workstations without a Firewall window activated, they both work as expected.

  It must be remembered that in firewalls, even if they are able to respond to ICMP if the request is from a different subnet, they will not be because he is recognized as a network abroad. You must know the network on these computers or make sure the computer does not care.

  You may be able to do this by simply adding additional subnets on the advanced configuration of the network card (if it does not take too much address space) as an example.

  Or well, as you have discovered that you can add routes, which is a bit heavy and inconvienent, but effective.

  -Tom
  Please mark replied messages useful

• How to configure the VLAN-access plan on Cisco 3650

  Hello

  I would like to configure the VLan-access plan to filter some of the traffic VLAN, but I am unable to run vlan-map command on the cisco L3 3650 v03.06.00E

  Hello ahmed,.

  According to the command search tool, 3650 v03.06.00E does not support the vlan-access plan.

  You will need to catalyst 3650, 3SE to configure "vlan access map.

  https://Tools.Cisco.com/support/CLILookup/cltSearchAction.do

  Show vlan-plan of access (catalyst 3650, 3SE)

  VLAN-access plan (catalyst 3650, 3SE)

  I hope this helps.

  Please evaluate the useful messages.

  Thank you.

• A bet with the network team - configure the VLANs on Teddy does not work against Cisco?

  Hello

  We have a great place of Esx and I have a bet with one of the network Admins.

  I configured a vSwitch to work with 1 bear. On this vSwitch I configured 1 vlan with a Vlan ID 100

  I told the guy from the network to set up the bear side here and he said he has set up 'Access' and not trunk as normally I ask because it's only 1 Vlan.

  I said ok and we tried and nothing works, when I configured the Vlan 0 in the Esx, it started working.

  Of course we cannot leave it like that and need to Config the Vlan on the Esx.

  I told them that once I configured the Vlan on my side there is nothing to do there, and they need to do the thing here.

  they say the same thing.

  Who is right? It is something they need to configure side here if she's 'access' and not 'trunk '?

  or is it something at my side?

  This mayble help your network http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004074 management team

  and

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1003806

  Please, do not forget the points of call of the "useful" or "correct" answers

  Mauro Bonder - moderator

• Hi need help I get the error message "Download error, Undefined" in the applications tab to install Apps. Can someone help?

  Hi, I need help, I get the error message "Download error, Undefined" in the applications tab to install Apps. Can someone help?

  Follow the procedure below and check:

  
  

  End Adobe partner all tasks in the Manager of tasks like creative cloud, CoreSync, AAMUpdater... etc.
  

  Uninstall Adobe Creative Cloud application.

  If you face any problem try CC Uninstaller:

  Using creative cloud | Uninstall the creative cloud desktop application

  After removing Adobe Creative Cloud applications, follow these steps:

  Step 1:

  Open the c: drive and navigate to C:\Program Files (x 86)------\Adobe " common files".

  Open the Adobe folder and delete folders named Adobe Application Manager and OOBE.

  Step 2:

  Navigate to C:\Program Files (x 86) \Adobe.

  Open Adobe file and if present the file to remove Adobe Creative Cloud . [* important]

  Impossible to remove?

  Rename it as Adobe Creative Cloud-old.

  Step 3:

  Press Windows button (located between Ctrl and Alt buttons) with the key R together at once, you will get a command window.

  Type below command and press the enter"" key.

  AppData

  Then go to the Local > Adobe.

  Open the Adobe folder and delete folders named AAMUpdater and OOBE.

  
  

  Step 4:

  Temporarily disable anti-virus and firewall.

  
  

  (1) open Control Panel and then click on the network and Internet"" option.

  2) click on Internet options, click on the tab "connections".

  (3) in the 'Connections' tab, select 'LAN' settings, you will be able to view the LAN settings box.

  (4) check the box-"automatically detect settings" and then "uncheck" all the other boxes as "configuration Script auto use", "Use a proxy server," proxy server ", then click on the ok button."

  5) click on the "Network settings" button once again, make sure that "Automatically detect settings" is the only option you select, the window of properties of LAN so clear.

  
  

  Step 5:

  Make sure that Adobe Creative Cloud is not listed in the control panel > programs and features. list.

  Then, download and install the Adobe Creative Cloud app and check.

  https://ccmdls.adobe.com/AdobeProducts/KCCC/1/Win32/CreativeCloudSet-up.exe

• Need help to diagnose the regular system analysis on iMac - processors maxed out

  I need help to identify the cause of a problem that occurs at least 2 - 3 times per day using my iMac (27-inch, mid 2010) running 10.11.5.

  I will use my iMac and then all at once things will start to really trolling. To the point of being completely unusable. Even if I'm able to move my cursor, then click to drag the windows around the screen nothing does really.

  I have iStat menus running so that can see graphics in my menu bar that all 4 cores are completely overfished. Occasionally, I was fast enough to launch the activity monitor to try to see what applications / services are responsible for, the use of % CPU column is completely empty of values, so I can't identify the culprits in a reliable way. I try to keep that column sorted by % CPU use in the hope that he could reveal something and normally it's the kernel_task who is up there.

  I use a Wacom Bamboo dated Tablet (MTE - 450 has) instead of a mouse, and at one point, I was convinced the pilot of PenTabletDrive it is based on was to blame. I contacted Wacom on this subject, and although there is no known issues they pointed out that although the latest drivers will allow me to use the tablet that they no longer support older devices. I was wondering if there was a problem of communication between the device and a driver that is no longer supported. I installed the latest driver supported for my tablet, but the problems persist.

  It may be interesting to note that, when my computer is in this semi-frozen state, I am able to launch the window enough force and quit all open applications leaving me with only the Finder. I guess that means that there are none of my apps running and it is probably one of the services. If I restart the Finder system grinds to a completely enclosed holt.

  I hope someone can let me know what I can find in the Console or elsewhere to help me finally zero in on what is to blame. I can share a log if that helps.

  Thank you in advance!

  Information that might be useful:

  Kept by I tend to be running: Adobe InDesign, Photoshop, Acrobat (all CC 2015), Mail, Safari with several tabs & Dropbox sync constantly.

  Download and run EtreCheck, created by one of his own assistants here in CSA. It is a diagnostic tool that is very useful for us to find problems. It will also give us additional specifications on your Mac. After his execution after the logfile here. It will never contain any personal information.

• Need help to remove the zeros on the right

  Hello.

  I need help to replace the zeros in the string.

  I have a string which is the output of the network packet. There are a few trailing zeros in the package.

  I don't see them in normal mode, but the size of the string tells me that it's bigger then it looks like.

  When I pass in hexadecimal mode, you can see zeros.

  I tried to use the find/replace function allows you to search for 0 and replace it with an empty string constant. But, for some reason any, that he took no zeros.

  I need to stop the string that follows * 69.

  

  Show your code.  You won't find and replace with all zeroes.  These 00 in hex mode they are null characters.  (not printable byte with a value of zero).  You need search and replace on that character.  (replace string should look like 00, when it is set to display the hexadecimal code.

  

• cq57: need help cq57 enter the password administrator or power on password... deisabled system 58555314

  need help cq57 enter the password administrator or power on password... deisabled system 58555314

  Thank you!!!

  @clatimer

  Enter 47433930

  REO

• Need help in using the ActiveX to retrieve a VARIANT

  Need help in using the ActiveX to retrieve a VARIANT.

  Variant is shown as var {VT_Ul1, 1} in debugging

  By using the following

  HR = CA_VariantGetShort (& var, &value);)

  I get 0 for my answer instead of 1.

  Answered my own question.

  VT_Ul1 is an unsigned char and not a short.

• I need help to Flash the bios. I have an Aspire 5810TZ. I start and it just says: "acer".

  I need help to Flash the bios. I have an Aspire 5810TZ. I start and he just says "acer" and goes no further. I went to the download page for BIOS on us.acer.com and it has a zip file with 5 files:
  JM4151135.exe
  IN FLORIDA...
  GPC_V135.bin
  Readme.txt
  FLASH. BAT
  What should I do? I tried to copy the files on a USB key and turn on/off with Fn + ESC key. After the release the power button and pressed Fn - Esc another screen appears after 30 seconds. I gave up and gave her 30 minutes but it does nothing. I read another person that should be flashing power button online. I have to rename one of the files. Help, please!

  Aspire 5810TZ menu of frozen startup.

  I finally understand it.

  I couldn't start a back b/c drive, it me did not start anything.

  I followed this chain of logic:

  -Downloaded the bios (2.35 is the one that worked for me)
  -Find the exe file in the winflash file.
  -Extract the files in archive exe using the 7-Zip program
  -Find the .fd file and rename it to JM41X64. FD (I read in a forum was unique in my laptop)
  -Copied JM41X64. FD and FLASH it is. EXE on a USB
  -A the battery and the hard drive out.
  -With its trendy diet I supported Fn + Esc and that you press the power button once while ensuring that the Fn + Esc has been always held down.
  -J' waited 6 seconds and release the Fn + Esc and seen the flashing flash player
  -After about 10 minutes, restarted the machine and the bios as like new.

  Later, I found that there was a hard drive problem.

  I want you guys should help more. All I needed was the name of the JM41X64 file. FD and you don't know how many hours I put into trying to find how simpy bios flash. It is not that difficult for someone with a b.s. in computer science to learn how. Couldn't we a m.s. back b/c the bios drive was messed up. F12 didn't work.

• Need help now for the live installation

  Need help now for the live installation

  Hello

  As described in the question, I understand that you need help. I will definitely help you however, I would be grateful if you could help me with more information to better understand the problem and resolving it.

  1. What is the problem you are experiencing during installation?

  2. That you install? Any software or operating system?

  3. How you try to install the software/Os/application?

  If you need live support from Microsoft then you can click on the link given below and check if it helps.

  https://support.Microsoft.com/en-us/contactus/

  Hope that this help, please write us back for any further assistance on this point, we will be happy to help you further.

• Need help to install the network on laptop drivers

  I have a laptop of HP 2000-239WM and recently erased due to trying to sell. However, when I reinstalled everything back on the PC, no network drivers have been installed, so I have no access to the internet, wireless and wired. Should what programs I install via USB in order to solve this problem?

  The network adapter driver specifically requests the Ethernet, wifi and it...

  Hello McKinley,

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that you need help to install the network drivers into the laptop.

  Certainly, I understand your concern and will try my best to help you.

  In order to install the NIC drivers in the system, I suggest to visit the link below and check if that helps.

  http://support.HP.com/us-en/drivers/selfservice/HP-2000-200-notebook-PC-series/5091493/model/5119030

  Note: Make sure you have access to the internet to another computer and download the network drivers using the USB and install on your laptop.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• Need help to uninstall the game Deadspace

  Original title: uninstall Deadspace

  need help to uninstall the game Deadspace

  What you're looking for?
  http://help.EA.com/en/article/manually-uninstalling-dead-space/
   
  Revo uninstaller can be faster.
   
  Revo Uninstaller
  http://download.CNET.com/Revo-Uninstaller/3000-2096_4-10687648.html

• Need help to retrieve the magnetic border

  As the title says, I need help to get the magnetic border thing (I don't know what his name). It helps a lot when I am rearraging my dekstop icon so that they are all neatly. Its the sticky feeling when you put an icon next to each other. I installed Stardock Fences before and which could lead to the missing or disabled?

  Hello

  • Right-click on an empty part of the desktop
  • Leave the mouse on the view
  • Click Align icons on the grid

  Tricky

• Need help to identify the type of object in the loop of pl/sql

  Hello

  I need help to identify the Type of object declared beneath a procedure as shown below:

  I need to pass the parameter to the procedure as a TYPE of OBJECT and also refer to variables of Type Object in a loop

  create or replace type TEST_VALIDATION_REC is RECORD (order_num varchar2 (30),)

  number of inventory_item_id

  reserved_YN varchar2 (1).

  error_flag varchar2 (1).

  Error_message varchar2 (2000)

  );

  CREATE OR REPLACE TYPE VALD_TBL AS VARRAY (10000) OF TEST_VALIDATION_REC;

  PROCEDURE ADD_TO_ORD)

  p_lot_number_list IN VALD_TBL,

  p_ord_number IN Varchar2,

  p_user_id in NUMBER: = fnd_profile.value ('USER_ID'),-change 1.10

  p_responsibility_id in NUMBERS: = fnd_profile.value ('RESP_ID'),-change 1.10

  p_application_id IN VARCHAR2: = 'PO',-change 1.10

  x_error_flag OUT Varchar2,

  x_error_msg OUT Varchar2

  )

  In the above procedure, I had the VALD_TBL. Is it OK?

  And how in the loop if the records if I use:

  FOR indx1 IN 1.p_lot_number_list. COUNTY

  LOOP

  BEGIN

  SELECT

  inventory_item_id

  IN

  ln_item_id

  Of

  dummy_lot_tab

  WHERE

  lot_number = p_lot_number_list (indx1); - > how direct the item here?

  EXCEPTION

  WHILE OTHERS THEN

  ln_item_id: = NULL;

  END;

  Records are PL/SQL objects.  They are not the SQL objects.  You can create a SQL TYPE (schema level) as a collection (variable-tables only, tables nested).

  So therefore your first statement is syntactically incorrect

  CREATE OR REPLACE TYPE TEST_VALIDATION_REC IS RECORD
  (order_num VARCHAR2(30),
  inventory_item_id NUMBER,
  reserved_YN VARCHAR2(1),
  error_flag VARCHAR2(1),
  Error_message VARCHAR2(2000)
  );
  

  You must put in an anonymous PL/SQL block or the stored procedure

  DECLARE
  
     TYPE test_validation_rec IS RECORD
     (
      order_num VARCHAR2(30),
      inventory_item_id NUMBER,
      reserved_YN VARCHAR2(1),
      error_flag VARCHAR2(1),
      error_message VARCHAR2(2000)
     );
  
     TYPE vald_tbl iS VARRAY(10000) OF test_validation_rec;
  
     lv_tbl vald_tbl;
  
  BEGIN
  
     lv_tbl := vald_tbl();
    -- insert your code here 
  
  END;