Need traffic Analyzer - Capture packets from CISCO
I use a cisco router, I've created interfaces sup, I use public IPs - now I need to check the traffic flow...
I need the same information below.
1. IP source address
2. source port
3 destination IP
4 destination Port
5. date and time of access
I want to capture the details above from the cisco router.
What is the solution for this, cisco can help me in this.
According to your hardware/ios, what you will need to check what features you have available and what it supports
Most routers are limited that they cannot support SPAN but 3845 s can or you could focus on the use of the RITE feature
Some routers also supported the monuitor capture buffer
http://Tools.Cisco.com/ITDIT/CFN/JSP/index.jsp
https://supportforums.Cisco.com/document/29616/utilizing-new-packet-capture-feature
http://www.Cisco.com/c/en/us/support/docs/switches/Catalyst-6500-Series-switches/10570-41.html
http://www.Cisco.com/c/en/us/TD/docs/iOS/12_4t/12_4t11/ht_rawip.html
Tags: Cisco Support
Similar Questions
-
How to activate IP accounting or capture packets in Cisco ASA 5510 (8.2)
Hi all
Please help me for activation
IP accounting packets or capture in Cisco ASA 5510 (8.2).
Thank you
Solene
Hi Eric,.
Create a list of access with the source destination ip address and/or tcp/udp ports
can use it
CAP_NAME access-list ACL_NAME buffer 12345bytes INT_NAME capture interface
You can check capture
See the capture?
Name Capture PASSWORD
| Output modifiers
Take care
PaulC
-
I need manage the bandwidth used, PowerConnect 6224 traffic collision and packet traffic. I downloaded the MIB from the Dell support site and I saw thar there are about 105 MIB in the downloaded file. My question is: in what Mib, I can find the OID which allow me to monitor the above?
Thanks in advance
Rogerio
Unfortunately, there is not a complete list of the different OID in different MIB. In order to find this info to simply browse through the different MIB seeking the OID, you need. We did some looking through the MIB and found these OIDs that can help you. Another thing to keep in mind is that the MIB downloaded are in general of a group of switches. So there are situations where a /OID MIB listed will work for a certain model of switch with certain level of firmware.
RMON-MIB
FastPath-cos-qos-mib
Another method, some people have had success, done using a SNMP walk.
http://www.snmpsoft.com/freetools/snmpwalk.html
I hope this information helps. The method of importation for these MIBs can change based on the management/tracking software that you use.
Thank you
-
Help to capture packets on a system MXP running F9.3.3
Someone at - it a good set of instructions on how to make a capture of complete package on an MXP endpoint.
I'd like to do something that I can open it directly in Wireshark.
We seek to verify that the DSCP marking are sent and received on UDP traffic that is sent and received since a MXP.
I have all the DSCP settings in the configured MXP, but I want to check that the markings survive at the end.
Require Root access?
I see that in a log rather than a full packet capture file?
We use capturing packets in the regular TC7.1 of the bases and is working very well... wish they would add to the web interface MXP
Thank you
There is no way to handle this grimly on an MXP endpoint.
So you have a switch that supports a monitor mode (okay we need to
Trust the switch to show what you want to see) or some other capture
a device that you can inject into the path.
Good success.
If this post was helpful please rate this post with the stars below!
-
ESXi 5.5: Enhanced Capture packets at the host level
Can someone explain how to use this new feature?
Capture packets of improved host-level
Network troubleshooting requires various sets of tools. In the environment vSphere VDS
offers standard of monitoring and troubleshooting tools, including NetFlow, Analyzer SPAN (Switched Port).
Remote Switched Port Analyzer (RSPAN) and encapsulated remote Switched Port Analyzer (ERSPAN). In the present
release, an improved host-level packet capture tool is introduced. Packet capture tool is equivalent to the
tcpdump command line tool available on the Linux platform.
Here are some of the key features of the packet capture tool:
• Available as part of the vSphere platform and can be accessed through the vSphere host command prompt
• Can capture traffic on VSS and VDS
• Captures packets at the following levels
-Uplink
-Virtual switch port
-- vNIC
• Can capture packets ignored
• Can follow the path of a packet with details of time stamp
Cannot find documentation for this tool and tcpdump-uw is exactly the same as in 5.1.
The new command is run on the host computer and is called pktcap-uw, I just finished writing a blog post about it here
-
FCPX - captured live from a remote camera?
Experience scientific, a little dangerous. I have a Sony FS700 camera trained on experience. I want to be able to run a USB cable from the camera to a control booth closed about 20 feet. I want to be able to control the camera from a Macbook Pro. I also wonder if there is a way to capture data that is ensuites directly into the computer (on an external hard drive) using the may output HDMI Cable? ... I remember that old Final Cut get live data from a camera.
FCPX do something like that?
Or maybe someone has a suggestion how it could be done?
All ears,
Ben
FCP X cannot capture alive from a camera via USB. In fact, USB does not have the live video from the camera anyway, so no software can't.
You can take the output of the camera, but you would need a HDMI input device. The HDMI on the MBP is for * output *, do not input.
If you get a device like BlackMagic UltraStudio MiniRecorder, then you can use the BlackMagic software save and then import the resulting in FCP X film.
PS: Really you run 10.6.8? What model is your MBP?
-
OpenManage Network Manager 5.3 does not display the data traffic Analyzer
Hi I have OMNM installed on a virtual machine and a PC Dell-6248 okay discovered and that responded to the questionnaire. However the flow of traffic or Traffic Analyzer features do not work. I recorded the switch (click right switch\Traffic Analyzer\Register) and activated sflow on swtich (port 6343) and implementation of the polling and sampling on a few ports in order to generate traffic data. The data appear to be sent from the switch ok because I tried to install the application SFlow trend on the same machine as OMNM and that contains traffic data, no problem.
Java 7, ActivePerl, Adobe Flash and reader are all installed and firewall disabled. The only other thing a bit strange is that the network display feature works on Google Chrome, it doesn't work on FireFox or IE and Performance indicator Gagues (CPU usage, memory usage, temperature) do not work either. I'm not sure if they are related to the Traffic Analyzer problem...
Windows Server 2008 R2 64 on a VMWare virtual machine. PC-6248 switch sfotware version is 3.2.0.7
Any help would be appreciated.
Thank you
Andrew
Eventually found the problem here. The absence of traffic Analyzer data was caused by the presence of an interface VLAN IP address on our switch. I had recorded the physical switch ok in OMNM, but the sflow data do not seem to come from the IP Address of the switch when I ran a trace of Wireshark on sflow traffic. Instead sflow traffic came from a different IP address that turned out be a VLAN IP interface. As the what IP interface was not mandatory on the VLAN special (he was there for outside access mamgement band only), I managed to remove (only the period of INQUIRY, not the VIRTUAL local area network) and now sflow traffic appears to come from physics going on own IP address. I then started to get traffic Analyzer data in OMNM.
Thanks for your suggestion on the use of Wireshark to plot the data on this guy as he lead me to the solution.
Andrew
-
Internet works is not in LAN behind a router from Cisco 881
My internet does not work in local network that is behind the router from Cisco 881. Here is the configuration of the router.
Help, please...
Current configuration: 1478 bytes
!
! Last modification of the configuration at 08:16:12 UTC Wednesday, February 6, 2036
!
version 15.1
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname R1
!
boot-start-marker
boot-end-marker
!
enable secret 5 CATz $1$ $ VqnIsAQvFHHnV9E/Q6RMV0
!
No aaa new-model
iomem 10 memory size
!
!
IP source-route
!
!
DHCP excluded-address IP 192.168.1.1
!
IP dhcp pool dhcppool1
import all
network 192.168.1.0 255.255.255.0
default router 192.168.1.1
DNS-server 202.56.230.2 202.56.230.7
!
!
IP cef
name of the IP-server 202.56.230.2
name of the IP-server 202.56.230.7
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FGL1539254Q
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
IP 182.73.122.54 255.255.255.252
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
!
interface Vlan1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly
!
router RIP
version 2
network 192.168.1.0
!
IP forward-Protocol ND
IP http server
no ip http secure server
!
overload of IP nat inside source list 101 interface FastEthernet4
IP route 0.0.0.0 0.0.0.0 182.73.122.53
!
access-list 101 permit ip 0.0.0.0 255.255.255.0 any
!
!
!
!
!
control plan
!
!
Line con 0
exec-timeout 5 30
password vinayak123
opening of session
no activation of the modem
line to 0
line vty 0 4
password vinayak123
opening of session
transport of entry all
!
endHello @[email protected] / * /;
Thank you for your message. I had a glance on the configuration for you. You used a network as opposed to a wild card mask in your access control list for your NAT statement. This changed the field from the source to 0.0.0.0 automatically, which is going to be does not match your interior traffic and NAT'ing outside.
To fix this, please run the following commands and test once more.
no access-list 101access-list 101 permit ip 192.168.1.0 0.0.0.255 any
Thank you
Luke
Please evaluate the useful messages and mark the correct answers.
-
SSL VPN may be configured on the router from Cisco 881/K9?
I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9.
Please someone advise me.
If Yes, for only 5 users, what I need to buy the license or license is supplied with the router?
Thank you.
Yes, and you need a license:
FL-WEBVPN-10-K9
License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions
FL-SSLVPN10-K9
License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions
-
I can't get CS6 to recognize my Sony DCR-TRV340 camera to capture video from this camera. The CS6 capture Tin can, set up a message that a capture device is offline. Camera Sony DCR-TRV340 is not listed in the CS6 device Type list in the CS6-DV/HDV cameras Sony device control settings box. I downloaded what I believe are the right drivers for the TRV340 and when I connect the camera to the computer, the computer shows it is in the box devices and printers, but CS6 do not recognize. Do I need to install these drivers in a specific CS6 program folder? If Yes, where can I find these drivers in the Professional operating system of windows 7, and in which folder CS6 would copy their?
Thanks John,
The controller IEEE 1394 of switching for the Legacy driver did the trick. CS6 now recognizes my camera. Thank YOU MUCH for the help!
Chuck
-
I need to get the bookmarks from a backup hard drive that the system failed on. were can I find the file/folder of bookmarks?
User Agent
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729 .NET CLR 3.0.30729; NET4.0C; Media Center PC 6.0)
Bookmarks are stored in a file called places.sqlite in the profile folder.
To find out where the profile folder, see http://kb.mozillazine.org/Profile_folder_-_Firefox -
Need to move bookmarks FF from old computer to new computer. Where are they located on a Mac OS 10? I still have access to the old backup hard drive.
See http://kb.mozillazine.org/Backing_up_and_restoring_bookmarks_-_Firefox
-
capture audio from an old tape recorder.
Dear Sir.
I wear it in front of you I have connected an old tape recorder with me to my PC to capture audio from the recorder. I did not understand how to capture the audio later.Kindly advise me appropriately if possible through a video in order to understand how to connect the tape recorder and capture the audio of my old tape recorder. There is that mic symbol available to connect to the computer.Thanking you,YourRambeauThe free Audacity software might be worth a try:
Audacity
http://Audacity.sourceforge.NET/Features of Audacity
http://Audacity.sourceforge.NET/about/featuresAudacity tutorials
http://Audacity.sourceforge.net/manual-1.2/tutorials.htmlHow to scan discs vinyls, audio tapes and minidiscs?
http://Audacity.sourceforge.NET/Help/FAQ?s=recording&i=records-tapesHow to record tapes to PC/computer
http://www.online-tech-tips.com/computer-tips/transfer-audio-cassette-to-computer/How to copy tapes to hard drive
http://www.WikiHow.com/copy-cassettes-to-computer-hard-driveTransferring tapes and records to computer or CD
http://wiki.audacityteam.org/index.php?title=Transferring_tapes_and_records_to_computer_or_CDHow to save my recording on an audio CD?
http://Audacity.sourceforge.NET/Help/FAQ?s=files&i=burn-CDAudacity can record RealAudio or other audio streams?
http://Audacity.sourceforge.NET/Help/FAQ?s=recording&i=streamingRecording with Audacity
http://Audacity.sourceforge.net/manual-1.2/tutorial_basics_4.html -
I put in a new windows xp en my cable internet is not werking why is that what I need to down load drivers from dell for this
Your Internet drivers are not part of XP. If you bought the device from Dell, you have other records besides that reinstall drive? I had 3 machines from Dell and they all came with the CD of drivers among others.
-
Hi, I bought an IBM Thinkpad with XP Home Edition pre-loaded in 2005 (the XP key sticker is on the bottom of the laptop), but did not receive an XP installation CD - I understand, it is a common practice. I want to improve the internal hard drive (for a bigger) then you will need to re - install XP from CD. They tell me that there is a way to create the XP (on the CD burner) installation installation CD but have no idea how. I can't imagine I'm the only person to have had this problem. Can you tell me where I can find the instructions how to do this please? Any help is welcome. Thank you very much.
There are many cloning utilities, but I recommend Acronis True Image. You can clone your hard drive, then use TI to the image of your system and to make incremental backups. MS - MVP - Elephant Boy computers - don't panic!
Maybe you are looking for
-
New software download Iphone4s
I have an iPhone 4 s and tried to download the new software, asked to attach the phone to iTunes, this is not possible as long as no access to do it, I can get around this at all? Phobell joint
-
Number transfer Skype new account
I wonder if this is possible. I have 2 Skype accounts and want to transfer the number to one account to the other account.
-
Sharing of Variable error-1950679023 in LabVIEW 8.6.1
Hello Is anyone else having problems with this error after installing LabVIEW 8.6.1? Programs using variables shared that I wrote (and worked), just in older versions don't seem to work. Kind regards Sarah
-
Forgive me if this has already been discussed. I just joined this forum. I have a Rebel XT using a card CF. I have reflected on the upgrade to a new camera, but do not need to get a new one. I use mine only for family and travel pictures. I would lik
-
HP OfficeJet 5610xi all-in-one: windows 10
After you have installed Windows 10, I get the following error message when you try to print from applications: We could not reach this printer. Make sure that the printer is turned on and that you are connected to the network printer, or try a diffe