NETGEAR D1500

Similar Questions

• D1500 Antenna Essentials

  I am trying to compare the values of Netgear D1500 antenna with other brands.

  There is no reference to it in any documentation I can find it; Anyone know if the antenna is 2, 3 or 5 DBI?

  Hello camdave

  The antenna gain is 2dbi.

  DarrenM

• Cannot connect BT Hub 6 to Netgear booster

  I upgraded my BT home Hub of a 5 to 6. The BT Hub 5 connected before my booster of Netgear (EX6100).

  I tried to delete the old network Netgear since my IPAD - BTHub5-PMP3_2GEXT, however, the tab "network don't forget" does not exist.

  The BT Hub is connected to a desktop via Ethernet cable

  I tried to put the booster of Netgear next to the hub and connection using the WPS button, it does not connect.

  Any suggestions please.

  Steve

  The booster can be to remember the old network. Is it possible to reset (clear) so he starts again?

  You will perhaps connect to the EX6100 using your iPad and configure it manually, as explained in the manual.

• Time capsules can extend a Netgear network

  A time Capsule can be used to expand a network of Wi - Fi Nighthawk Netgear router X 6 AC3200 Tri - Band (R8000)?

  The best answer we could provide... as you do not specify if you intend to "extend" the Netgear using Ethernet or Wi - Fi connection... would be Yes and no.

  Yes, if you connect the Capsule on the Netgear router using a wired Ethernet cable connection, permanently.

  No, if you think you have the time Capsule only connect to the Netgear wireless network.

• 1 St gen AX and connect to the new network Netgear M/R...

  Updated my cable modem/router to a Netgear C7000 and can't get my 1 St gen airport to reconnect to my network - Express use only in client mode to stream iTunes to amplified speakers. Have you tried all the typical solutions, but wonder if the problem may be with the security settings. The 1st gen AX supports WPA2-PSK security?

  Yes, he does.

  However, users often get confused about what could be a 1st Gen AirPort Express.  Please check to locate the model number of the Express... it's on the side of the unit... hard to see... so you need good lighting and reading glasses.  The model number starts with an 'A' follow-up of four digits.

  A 1st Gen AirPort Express is A1264 model number.  The 1st Gen means that it was the first Express to use 802.11 "n" wireless.

  If you see A1084 or A1088, it is wireless a lot more old "b/g" which has been sold long before that Apple has started using the generation of naming when 802.11n model was introduced in 2008.

  If that's what you have, then you will probably need to use WPA - PSK - TKIP security settings.

• Can I watch movies from my Netgear Stora on the new Apple TV

  Hi, I have a Netgear Stora as a server for movies, if this is related to my router as it is now, and a new Apple TV if I can watch my movies?
  Thank you.

  Yes, there are a few apps that allow you to do this. In my view, Plex and merger are those that many use.

• Airport Express used as a range extender with a Virgin / superhub of Netgear does not work

  I use Wifi around the House on three floors and in the back kitchen.  in the kitchen, reception is poor, probably because of masonry between the modem and the kitchen walls.

  I bought an Airport Express 802.11n in January 2016 hub to extend the WiFi in the kitchen and I hope that the patio beyond.  The distances are not great - 10 to 15 m.  We have the Virgin as a provider with a Netgear Virgin Super Hub (490 VMDG).

  Express to the airport moved and this is confirmed when to check on my Mac with Airport utility, the MONKEY shows and itself a steady green light.

  Problem is that in using wifi designs in the kitchen the signal is poor to non-existent and when I turn off the EPA the signal isn't as well, which implies that the received signal is that of hub Super rather than the EPA.

  I guess I can't realized overall upward to extend an existing network?

  Any suggestions?

  The Airport Express is not designed to extend the signal of a 3rd party router, so if you try to have the Express connect wireless wireless and to extend the signal, he can not do with your Virgin Super Hub.

  The Express is designed to extend the signal from another wireless only router from Apple.

  The Express 'joined' your wireless network, it could be used to connect a compatible USB printer or for use with AirPlay.

  If you want to Express to extend the signal of the Super station, the Express needs to connect to the hub using wired Ethernet wired, permanent.

  Alternatively, another option would be to add another Express, install it near the hub and plug it into the hub with an Ethernet cable. Then, a 'distance' AirPort Express would be able to extend wireless signal of the Express 'main '.

• Can I use Intel Wireless Display - Netgear PTV1000 on Satellite U400-157

  I want to use the NETGEAR PTV 1000 wireless display device. The hammer on the Net says I should be able to use it if I change the operating system to Windows 7. I see that I need http://www.intel.com/support/wireless/wtech/iwd/sb/CS-031059.htm Intel Wireless Display to use.

  The Intel Wireless WifI Link 5100 wireless on the Satellite U400-157 is. Seems that it is not one that is required to run the PTV 1000? So an operating system for Win 7 can not allow me to use the PTV 1000?

  Found a similar thread about the use of the Intel Wireless Display
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=64770

• NETGEAR Push2TV with Satellite Z10T on Windows 8

  Hello.

  Try to get a Netgear Push2tv (PTV3000) with my new Z10t (PT132A-00F00T). The Netgear support pag2 says I need driver Wifi Intel wireless display, V3.5.41.0, V15.5.7. Been go7ng around and in circles trying to download these versions, but without success. Can someone please tell me where I can download these for my Toshiba?

  Thank you... David

  Hi David
  All drivers supported by Toshiba, you can find on http://www.toshiba.eu/innovation/download_drivers_bios.jsp
  Support page drivers usually in the original manufacturers. Have you checked s Intel support page?

• Can I use Satellite R630 with Netgear and Intel wireless display technology

  Dear all,

  I am a user of a Satellite R630-105 (processor i3 M350). I would use this laptop with Wi - Fi on my plasma on the wall display. Recently, I heard about Intel wireless display technology connected to the Netgear adapter as a possibility for wireless connection to the screen.

  Can I use my computer with this technology? If so, what is the process? If not, is there an alternative, using cable is very inconvenient. I'm at the beginner level.

  Thank you very much, to come.

  Peter

  > I would like to use this laptop with Wi - Fi on my plasma on the wall display.
  Can you please me for what purpose you need this connection?
  I mean what kind of data you want to transfer?
  With other words you do exactly?

• Satellite L300 not connect to Netgear router

  Hi, I wonder if someone can help me.

  I recently installed a Netgear wireless home router. Although the Mac laptops and iPod in the House have all connected without any problems my Satellite L300 (PSLB8A-0VK004) is not.
  Curiously however Island L300 connects to a public network wireless outside my house without any problem.

  I have contacted Netgear, and they tried many things with me by phone. One of the operators of Netgear said it was a well-known problem of them and that he had a problem with Vista. They said I had to download Service Pack 2 for Microsoft (which I did) and the last 'Wireless drivers from the Web from Toshiba site'.

  I went to the Toshiba Download Center, but the drop-down list, it provides does not my laptop from its selection model. Also if I manually scan through the list of available downloads, I see those who are "Netgear Wireless Drivers".

  Can someone tell me where I can find these drivers?

  THX

  I think you Australian mobile phone model.
  Have you checked Toshiba Australia support and download page?

  Here is the link - http://www.mytoshiba.com.au/

• My R200 cannot detect Netgear DG834G

  I have an access point and wireless Netgear DG834G ADSL modem that works well with my other computers. However, my R200 does not seem to be able to detect it. The R200 does not appear to be network detection problem my neighbour's wireless, so it doesn't seem to be a problem with the adapter wireless in the R200.

  I checked the support area for the latest driver for the Atheros card in the R200 and it is already installed. I have WEP enabled on the DG834G. I also tried an another R200 with the Agency, and which also has the same problem. The DG834G with a cable connection is fine. Is anyone aware of any problem of incompatibility with the Atheros wireless card in the R200 and the Netgear DG834G?

  Hello

  Filing of a title, you wrote that your unit doesn't detect access point, but I have to ask you once again: what is your unit a problem to detect or connect to the Netgear?

  If you have written that the WLAN basket features are not the problem it is really not easy to give you concrete advice.

• problem w / Airport Extreme base station and modem Netgear broadband

  I just changed to ATT Uverse to Time Warner - internet only.  With Uverse, I was using my Airport Extreme base station to create a wireless network, and it has worked well in this capacity.  When you switch to TWC, the tech got the modem (TWC allows you to buy your own modem, so I bought a Netgear CM600 a recommended model) enabled and works very well, but could not get the Airport base station to talk about her (yellow light blink on the base station).  So, he opted for a TWC wireless modem/router.  Interestingly, I found that I could plug the Airport base station in the TWC modem (without any reconfiguration, just plugged into the WAN port base station to the modem ethernet port, as I had had with Uverse equipment) and voila!  It worked immediately.

  So, I called TWC to retry my Netgear modem.  I have the base station power off, plugged on the ethenet port Netgear, put back under tension and just got the blinking light.  I know that the modem does not work, because my iMac's network to the internet through the base station, for the Netgear, and go outside and I can fine surf in this way.  So it is something in the wireless configuration that must be different between the TWC modem and the Netgear modem.

  Obviously, I'm not an expert at this, basic troubleshooting tips would be appreciated.  The base station functions as a router (I can connect through a port ethernet through it), it is simply not generate a WiFi network for me...

  Thanks for the tips

  Steve

  Carlsbad, CA

  So, he opted for a TWC wireless modem/router.  Interestingly, I found that I could plug the Airport base station in the TWC modem (without any reconfiguration, just plugged into the WAN port base station to the modem ethernet port, as I had had with Uverse equipment) and voila!  It worked immediately.

  If your AirPort Extreme has been in its original configuration, it would act as a wireless Internet router. If you connect another router upstream to the extreme, there is work, but you'll have a condition known as: Double NAT. This isn't necessarily bad, but should be avoided if possible. To do this is simply to reconfigure the downstream router (in this case, the extreme) under a bridge. This disable its functions of routing and remove the error condition.

  However, if your extreme base station has been reconfigured as a bridge, if connect you directly to a simple modem, like the Netgear CM600, then this configuration will not work because no device will provide the necessary routing functions.

  It's always a good idea to perform a full power recycle your network hardware during change of equipment. Maybe that's the only thing your missed when you design your own? If you haven't done so already, please give it a try with the CM600 & Extreme combo. After return your results.

• NETGEAR WG511T PC Card works fine on Satellite Pro A10

  A Netgear WG511T 108 Mbps Wireless PC Card works perfectly on this laptop?
  Thank you

  I n t have this card but theoretically it should work. Please read carefully the instructions to facilities and install it correctly. If you don t have the maximum speed of WLAN is not because of the laptop.

  Please inform us of the results. It will be very interesting to read your report how it works.

  Good luck!

• Satellite Pro C50 "unable to connect" when linking to Netgear WiFi

  WiFi error - could not connect to this network WNAP210 Netgear router.

  Hello

  I have a problem with my computer laptop connection with my router Wifi Netgear router WNAP210 model, when I type the password it says that it is unable to connect or sometimes that the password is incorrect!

  I contacted Netgear, and they suggested changing the name of the router to remove any trait symbols "_" underscore, I made it today but always this annoying message on the cell phone. It does the same thing on my Nokia Lumia 1320!

  I tried deleting found connections and starting from scratch and also changed the name of the router (which displays correctly when you scan for Wifi on the C50).

  Now it starts to get really wound up... Please please help?

  Thank you
  Adam.

  Hello

  You should check the configuration of the WLan router.
  First, you will need to use the same standard WLan (802.11 A/B/G/N) for the wireless network, as well as for the Wlan router.
  In the device-> Waln Manager map properties-> Advanced tab, you can choose the standard Wlan to Wlan card.
  You should also check the settings (WPA/WPA2 AES, TKIP) encryption. Not all standards are supported by each Wlan adapter! So please pay attention to this fact.

  Last but not least, you should also check if these connection problems using various channels (1-11)