NETGEAR D7000 - Mode Access Point - connection problems with iOS Devices

Hello

Having a problem with my Netgear D7000 in mode access point.

My laptop (MacBook Pro) can successfully connect to WiFi and my PC connects fine cable using the D7000 as a switch.

iOS devices, however, hurt that is to get or maintain a connection - even if they connect to and then some time later they will fall the network. Go to settings shows the client attempts to connect, but seems to be stuck with an assigned random IP (not on the subnet of law), no gateway by default, etc..

iOS clients are an iPad 3, iPhone 5 & iPhone 5 c. All about the latest version of iOS.

Other access points by train (Belkin, billion) that's fine.

DHCP etc. everything is managed by my router which is a constant for all devices and access points - but I tried to change that, and he has not made a difference also.

D7000 is on the latest firmware (v28), I tried to reset it and setting up from scratch, but no joy.

Any ideas?

Change the channel seems to resolved this problem.

Tags: Netgear

Similar Questions

  • connection problems with wireless devices

    I have problems getting my network connected to my E1200. Office Wireless is connected, but if a device needs a password, it fails to connect.  I went into the zone administration and changed the password, but clocks site right after she says my settings have been saved, and devices do not recognize my new password.

    The administration area is for router functions.  Modify or use the password in the wifi section. It is to connect to your network.

  • computer automatically starts in safe mode without prompting, a problem with your computer might be preventing Windows from start normally__

    computer automatically starts in safe mode without prompting, a problem with your computer can prevent Windows to start normally

    Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

    If the system restore does not work, do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

    If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

    Good luck and I hope this helps. Lorien - a - MCSE/MCSA/network + / A +.

  • How to access a rv180w in mode "access point."

    Is there a way to manage the device when is in mode "access point"?

    Or at least access?

    Have Pietro Hi, you tried accessing it via its IP address? Perhaps search using MAC address in the DHCP of the router/gateway DHCP client table is connected to. The MAC is written on the label at the bottom of the unit.

  • I have connection problems with Skype video chat (Internet Explorer 8 - Windows XP pro). What I haveto do to fix this?

    I have connection problems with Skype video chat (IE 8 - XP pro.) What should I do to correct this?

    Hello

    go to skype.com and make sure you have the latest version of their software.

    Kind regards.

  • Connection problems with atheros ar9002wb-1ng

    I have 2 computers laptop toshiba satellite.  I just updated my router to Belkin ac1200 wireless router.  I'm having connection problems with my satellite l750, with atheros ar9002wb-1ng wireless network adapter - keeps disconnecting with a signal strength low however the other satellite I with a realtek rtl8188ce wireless lan has an excellent signal strength and works very well - how to fix this?   I'm not very techno so easy instructions please.  Thank you.

    Hi Jak,

    Welcome to Microsoft communities.

    I understand that the wireless connection is disconnected.

    1. don't you make recent changes that caused the problem?
    2. any message/error code?

    Try the steps in the following methods and check the status of the issue.

    Method 1:

    Using the troubleshooter from network in Windows 7
    http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

    Method 2:

    Configure the computer to clean start State to check software conflicts and check the status.
    http://support.Microsoft.com/kb/929135

    Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 of the article mentioned above.

    Method 3:

    Wi - Fi and in Windows network connection issues.
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Please report if you are still having the problem. I'll be happy to provide you with additional options available that you can use to get this problem is solved.

  • connection problem with screen

    I bought a compaq presario cq61-421sa about 18 months ago, so it is now out of warranty, and I have a connection problem with my screen. the entire right is taken up by different colored about vertical lines 1 pixel everywhere and therefore can not see half the screen.

    any idea how much it would cost to get HP support to do a repair on it? as I don't have the confidence to do it myself

    Hello

    Thre are 2 things that are likely

    the video card

    (b) the screen itself

    To check this, simply connect the laptop to an external monitor (from a friend, parent,...) If nothing wrong with the external monitor, which means that the screen of the laptop is faulty, if the video card is faulty. I don't know the cost but I charge $640 plus a party; Sometiomes my recommendation is to buy a new machine.

    Kind regards.

  • I have problems with ios 9.3.5

    my ipod says it's still Friday, September 23 when it is Monday 26 and is stuck in the 04:00 time when I change the time, the screen turns off a color at random, then restarts then both will and I have to change but rest later if it changes at all used to date will not change anything and it runs still works when it wants to and it doesn't stay connected to WiFi , I have the ipod 5th generation and am not elligible for ios 10 Please if you can solve this problem with ios 9.3.5 I would be very grateful as I use my ipod for almost everything. Thanks - René

    It is a community based on the user. You do not speak to Apple directly. You can contact the Apple Support here: http://www.apple.com/ca/contact/

  • Help: problem with playback device

    Hello

    My dell latitude e7240

    and my headset logitech g150

    does not connect it says: problem with playback device

    It calls for 1 second then ends

    and when my friends try to call the said

    contact can only receive instant messages

    Help, please

    and fast

    Thank you very much

    I did a diagnostic test and other results are here

    https://www.dropbox.com/s/ipvyg52xhfwjrly/Dxdiag.txt?DL=0

    and Skype is the last

    Thank you

    answer soon

    Morgan

    Topic/title edited for clarity.

    Still no trace of your helmet and Avnex Virtual Audio Device is always installed.

    The specified Audio Capture Source only is Avnex Virtual Audio Device

    audio Capture Sources :

    Microphone (Avnex Virtual Audio Device), 0 x 00200000, 0, 0, qcap.dll, 6.06.9600.16384

    Open the Windows Device Manager. Are there looking for this virtual audio capture device, then uninstall it.

  • Problem with recording devices and call issues

    Until recently I had a few problems with my microphone on Skype. Whenever I start my PC, everything will be fine, but every time I change the microphone source (from my webcam for stereo mix so I can play sounds in calls) and leave the call, I get weird questions. First if I still have the stereo mix as the source micro fine, but if I change it to my micro webcam when I click on answer call nothing happens and if I call someone it won't fail to connect and it will say: problem with the device registration, which is strange because it has nothing to do with the connection. Also if I change the source to microphone during a call, the call will be disconnected as if I turned on the internet and post something about the sound card errors. Can anyone help?

    I found the problem, clown fish was not working with Skype and it ceased to use the microphone and I thought since I had removed so I don't think that was the problem, but for some reason any, it is been installed, in any case I removed it and now Skype works fine.

  • Big problems with USB devices

    Since I upgraded to El Capitan I have several, serious problems with USB devices:

    1 USB hard drive: everything by watching a video from an external hard drive, the hard drive will be to disassemble all the minutes, the video will be of course hang and it takes 45-60 seconds until the drive reconnects. I also can not boot from any external hard drive more. Booting from a USB key works fine.

    2. I can't transfer my Sunny BT11 of beam data more. The Sunny Beam is a device that records the data of my photovoltaic plant. The overview of the system he sees when connected via USB, however he is not recognized and so I can't transfer data files. Also, it makes not a difference if it is connected via a USB hub or directly, the two versions do NOT work. In the Finder preferences, all devices are controlled to display on the desktop.

    The two scenarios always perfectly work with my Mac mini that has not been updated and uses Mac OS X 10.10.

    Hello Gulliver,

    It seems that if you live with loss of connection of your USB devices since the installation of Mac OS X 10.11 El Capitan, is that correct?

    I suggest that you are troubleshooting by following the steps in this article - OS X El Capitan: If a USB device does not work

    Thank you for using communities of Apple Support.

    Sincerely.

  • Unfortunately I can't move my watch to watch OS 2.2! Why! Is there a problem with IOS 9.3.1 really no advice did not work

    Unfortunately I can't move my watch to watch OS 2.2! Why! Is there a problem with IOS 9.3.1 really no advice did not work

    Hello

    If you have already installed a beta seed or a developer, first remove all beta profiles.

    Instructions are available here:

    Update the software on your Apple Watch - Apple Support

  • Problem with playback device?

    Video call in progress version 7.2.59.103 3 days ago made in New Zealand was in line for 40mins no problem what ever. as soon as I ended up call message problem with playback device. and as soon as I use either call or video call immediately, the page returns to the home page and does not appeal. checked devices audio all working correctly, no update of windows for the last 3 weeks. using Skype on my asus laptop 5 years on widows 7

    Hello, do not know what I did but trhe message has diasppeared, and the test call also works OK now.

  • I can't call anyone on Skype, he said only: "problem with recording device" help?

    Could someone help me? my lack of Skype let me call anyone, when I try to call or answer a call it comes a message saying "problem with recording device"-does anyone know how to fix this help please!

    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4158&LC=no&cc=no&DLC=no&sw_lang=&product=7264...

    You can install this "driver - Lyd" (Realtek High-definition-lyddriver (HD))

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-135685-1&CC=no&DLC=no&LC=No... =

  • Anyone having problems with iOS 9.2.1? Storage problems, apps not working?

    Anyone having problems with iOS 9.2.1? Storage problems, apps not working?

    No, not at all. Maybe if your were to describe the issues a little more in detail, someone might be able to help.

Maybe you are looking for

  • Pages M.I.A. problems: cannot read old docs Pages. Send heroes and advice.

    My beloved MacBook Pro (2011) crashed ugly, people from Apple (like you guys and girls) helped me to do a clean install, which cleaned up the seeds, but some important/sentimental data has been lost. Some of them can be recovered and some of them wil

  • How can I sort the selector non-unique values and make them unique in the structure of the case?

    I want to clarify 3 ranges as breeders of the case.  For example, I am able mV and I want 0.10, 10.20 and 20.30, but, when I enter them in this way, I get an error that says that the selection values are not unique. I want case to answer when the inp

  • Strange behavior with Scan function

    Hi, I see some weird behaviors with the scan function.  Here's a code (for Interactive execution) window which illustrates what I'm struggling with: #include static double value;// 1234567890123456static char buffer[20] = "- 24.612 g ?"; static int s

  • Windows is not valid

    The validation service is unable to determine whether this copy of Windows Vista is genuine. This is the message I get on the site he send me when I click on dlte

  • How to contact technical support?

    Hello. I'm totally lost on this web site. Question is simple: how to contact technical support? Phone number? E-mail? My questions concerns the RV220W, I can not find anywhere, any help on this, expect sound manual user guide. Kind regards.