NETGEAR Wireless Router WNR2000

Similar Questions

• I recently purchaced a Netgear wireless router. I can't get any Internet access every time I connect to the internet.

  I recently purchaced a Netgear wireless router, I can't get any Internet access every time I connect to internet

  Hello

  Your computer connects to other networks wireless?

  Check with the Netgear support, their online documentation, firmware and ask for their
  Communities and Forums.

  NetGear
  http://www.NETGEAR.com/

  NetGear - Support & community
  http://support.NETGEAR.com/app/

  NetGear - Forums
  http://forum1.NETGEAR.com/

  -----------------------------------

  Have you checked the updates or re-installed the driver of your WiFi? Check with the manufacturer of the system (motherboard
  Manufacturer of custom systems) If an edge device and/or the manufacturer of the device.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• orangle flashing light on netgear wireless router, but have internet via a modem... Please help

  I am connected to the internet via an ethernet cable via the modem I have, but the netgear wireless router that I have demonstrated a blinking orange Internet when I try to connect wirelessly, I tried to reset the router and the modem and had no luck, I also tried to penetrate in the maintenance of netgear online but who also won't allow me to enter. Finally I tried to release and renew my through the cmd ipconfig and shows an error message saying that the media is disconnected... Please help me

  Hello

  I suggest you to post the same question in the NetGear forums for support on the NetGear router and check if it helps.

  http://forum1.NETGEAR.com/

• You try to start a wireless router for my laptop. Can't define a wp5 Netgear wireless router should I can work only.

  Trying to set up a Netgear wireless network so I can use my laptop in the entire House.  I do not see the wireless on the screen.  Impossible to recognize that, if it is, is my wireless.

  Hello

  -Have you tried to update the network map?
  -You are aware of any changes made on the computer before this problem?
   
  Follow the steps described in the items listed below and check if it helps.
  
  Method 1: Uninstall the network adapter in Device Manager and reinstall the drivers for the network adapters on the manufacturer's Web site and check if the problem still persists. See the below link that can help you.
  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router
  
  Method 2: So I recommend that you follow the steps from the link below and check if that helps.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  Hope this information helps.

• I configured the netgear wireless router and works fine but when I turn the computer power off and back on I can't get connection

  Hi can anyone help, I am with AOL, I just switched to the Platinum service, I configured my router netgear DG834G wireless and that's all works fine, but if I turn the computer then turn it back I cannot get a connection and when I ask her to fiind wireless networks the computer tells me that windows does not support my wireless network and I must have another program running , but I didn't so I have to reload the settings again for windows to set it up. What happens whenever I turn off the computer. AOL are without help please someone has any ideas - I use windows xp service pack 3

  Hi Timstimpson,

  It is possible that the Automatic Configuration Windows wireless service is not configured to run at startup.
  Try the following:
  1. click on Start and run
  2. type in the box to run services.msc
  3 scroll down and look for the Automatic Wireless Configuration service
  4. double-click on the service and make sure that the Startup Type is set to Automatic
  
  
  Let me know if it works for you!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 09 Netgear wireless router

  NETGEAR requires a client to renew their contract to route every six months for $79?

  6 months ago, I got a call from someone claiming to be Netgear and I had to pay to renew my router service.

  I paid. I just got a call that I needed to renew once again for the same amount of money. This doesn't seem fair.

  Is it a scam?

  Elizabeth

  Hi @ooki we would like to tell you more about your report. One of our customer support team will contact you in this regard.

  Thank you!

• I have netgear wireless router for now I had I got a kindle and windows cannot locate it please help

  My kindle ask again me the password and I put in and says that it is bad while everywhere else it works.

  Hello

  I suggest you follow the given steps and later a update on the State of the question.

  a. Open advanced by clicking the Start button, then on sharing settings Control Panel. In the search box, type network, click network and sharing Center, and then in the left pane, click change advanced sharing settings.

  b. expand the home or work network profile.

  c. under the password protected sharing, click turn off password protected sharing, and then click save changes.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Links: http://KB.NETGEAR.com/app/answers/detail/A_ID/12744/~/how-to-view-or-change-your-wireless-network-password

  http://KB.NETGEAR.com/app/answers/detail/A_ID/1098

  More information: Wi - Fi and in Windows network connection issues:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• wireless router not working do not: told by iYogi technical support for wireless router Netgear that my registry is corrupt

  My Netgear wireless router (model: N300 wireless (WNR2000v3) router wireless) has stopped working properly without Internet access for my laptop (there was a triangle 'yellow' small 'i' (exclamation point) on the Wi - Fi signal strength indicator in the lower right corner of my computer screen.).  I bought only the router ago 3 months 25/08/2012.  Netgear technical assistance is really "iYogi technical support.  After more than 3 hours, Abdullah, Tech support person had me change what I think are 'DNS' settings for the router, and it now the next day, Thursday, November 15, 2012, works very well, "so far".

  My question is this.  The "iYogi tech support" person said, after took my computer during the process of fixing my problem, I had 9% of my corrupt computer registry files and I need to have a computer system 'optimize' made, then I wouldn't have the same problem with the router, and other problems with my computer, in the future.  The service would cost me $150 with 1 year tech support 24/7 from "iYogi" (support for Netgear tech. company) or $50 to do it once.  There was a LOT of pressure to pay then and not wait a day or more so I could think my 90 days of Netgear Tech. Free support ends on Thursday, November 22, 2012.  The person of 'iYogi technical support', Abdullah, said that because my Toshiba laptop has 4 GB of RAM and the Netgear wireless router has a very small RAM, then in a near future the problem could happen again and I have to pay a lot of money for the correction of a problem including my registry corrupted 9% of my Windows 7 (Home Premium (64-bit) with Service Pack 1).

  I had no problems with my computer that I've known since the purchase of this new about 2 years (a portable satellite youcef) ago.

  I have to have my system "optimized"?  My really register 9% damaged and if yes, is this normal or do I need to have it fixed?

  I was wondering if I had another brand of a router (for example the Linksys), I have the same problem?

  I would be grateful to anyone who helps to answer my questions and all the other advice on this subject.

  Thank you, or anyone in advance for all your help.

  Kind regards

  CCEntertain2M

  "Registry was damaged and needed optimization" - complete garbage, if the registry is damaged the PC does not start, the registry requires no optimization, third party that claims to optimize the registry software is snake oil and in the worst cases can make the system unusable.

  Usually if you have a router problem appear, of the first steps would be to reboot the router (unplug his pwr for a minute) and re start the PC. These steps are usually all that is necessary.

• Need help to connect the old Windows XP to new wireless router, please

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  The problem is probably that the Linksys E1200 is a wireless-N Router and your former Office no doubt has a wireless adapter that is only capable of wireless-G (or perhaps Wireless G and B).

  Are adapters wireless in your other computers wireless - n?  If so, it perhaps is the reason why they could not connect to your old G of Netgear wireless router.

  You can get a new wireless-N for the office adapter or configure the E1200 wireless g available.

• Problems to connect a wireless router to computer

  well, I have a windows vista desktop computer. I had remote access to my old House. I recently moved in with my sister and she has an acer laptop and a netgear wireless router. Ive been trying connect my computer to the wireless router, but it won't work. its plugged in the right place and everything and when I try to detect network hardware and settings, it keeps showing up as "windows doesn't detect any wireless network hardware" I do not understand why because its hip sister said she had a disc to install his wireless router but it no longer has the drive. do I need this disk to install the router or what? any help is appreciated, thank you.

  Hi keV ann,.

   
  The hardware you need for wireless technology includes the following:
  1. wireless network adapter. One for each computer on your network (laptops almost always have these built in).
  2. wireless access point or router (recommended).
   
  For more information, see setting up a wireless network
  NOTE: Laptops have a wireless button; Press the button to turn it on.
  We also recommend you to check the configuration of the wireless router. Please check the routers manual.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Can connect to the wireless router, but not to the Internet

  Because I could not find this post, I published in my problem to

  Windows 7, connecting Local only, no Internet

  I think I described the problem a bit better here.

  I had a Gateway DX4300-17 with Windows 7 Home Premium for about six weeks. I connect to the Internet via a Netgear wireless router. My Internet connection dropped often, but I've always been able to reconnect to the Saturday. Since the start-up my computer Sunday, when I try to connect to the Internet, the system tells me that I am connected to the router, but there is no connection between the router and the Internet. I did a system restore to Friday, but it did not help. I searched the Knowledge Base and tried several things I found there. Running "sfc/scannow" indicates that all is well. I disabled the '6' Protocol (I don't remember the letters that were with this, but you probably know what I mean). This made no difference either. I thought I would ask for help here in the hopes of not having to restart the computer to the "hospital". That's a very different problem here barely a week. I need help, please.

  Hello Bill6009,

  Have you tried to boot your computer in SafeMode w/network to see if the problem persists?

  If so, try to perform a clean boot to see if you encounter the same problem.

  Please post back your results if we can help get your problem solved J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• C4780 cannot find the wireless router

  I have a new iMac and old Toshiba that is running Windows XP and you use a Netgear wireless router.  When I got to the printer, it worked fine on the wireless network.  Bought a new router that I couldn't work with the Mac and the PC so I returned to my original router.  Now, the printer does not work as a wireless printer.  Summaries of diagnosis indicates that the printer cannot find the wireless router and fails under "Network Name (SSID) Found."  On the Network Setup page, my network is listed as a network discovered by the printer.  I guess there is a simple solution and hope to find the answers here.

  Thank you very much!

  Some printers C4780 left the factory with a default misconfiguration.  This could be the reason why you can not see the hpsetup network.  Here is an updated set of instructions for manually adding the C4780 to a Mac:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  Press the Scan button to get the wireless settings

  Select wireless Menu

  Select wireless settings

  Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks then ShowAll bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  The printer Web page, select the network tab, and then select Wireless (802.11).  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• Atheros 5007 won't stay connected to the Netgear WNR3500 router internal wireless

  I just bought a new laptop Compaq CQ60-420us (nw156ua) a week ago. Machine comes with Vista Home Premium and I installed Win7 rc1 64 on another partition.

  Initially I could not it remains connected to my router for more than 15 minutes approximately. I just press the wireless button to turn it off and turn it back on. Who would fix it for about 15 minutes.

  I called HP support, they tried many things including for me to do a factory restore.  They finally decide to send me a new wireless card. I received the new card yesterday, had it installed and it is essential to do the same thing. Last night, I dug an older linksys wireless router that I have used in the past. Hooked upward and the laptop stays connected to her very well. I had the wpa security enabled on the linksys routers both netgear.

  Then, I went to the netgear router and disabled security. It is very well connected. Not sure if wep security will allow him to work. I refuse to use just the wep security. It is easily hackable. And of course I will not let it be secure.

  So it seems to be a compatibility issue between my router netgear wrn3500 and the atheros 5007 wireless card security. The router has the latest version of the installed software package.

  I guess I'll call HP tonight and see if they can send me a different brand/model wireless card. All my other wireless devices work fine with this netgear router. I don't want to get rid of the cause of netgear, this is a gigabit & Wireless N router.

  Does anyone know of any other mini pci express card that works with my laptop? I would get a card N. I thought maybe the intel wifi link 5100 card. Not sure if those who are compatible with HP or not.

  Thank you!

  When I called HP back support, they were completely useless. Everything I tried to ask them is if they could just give me a list of wireless pci-express cards that would be compatible with my laptop. They did not understand my problem and could not give me a list. I wanted to the list because I read several times that HP has a 'white list' cards that will work with their motherboards. If you put a card that isn't on the list you will receive a message to remove the card from the bios when you turn on the machine. I checked this by testing the intel 5100 card on my laptop and it gave me this message.

  Oh btw, it's MUCH safer these days to update the bios of your computer, it was many years ago. I do all the time and have never had a 'brick' on me. Even safer on a laptop with a battery in good condition. In fact I recommend it as part of your troubleshooting process. That will not fix the problem tho atheros wireless.

  However, in the end, I was able to operate pretty well no thanks to HP!

  I had to buy another card Atheros tho. It was the 5009 Atheros. And it's a card N I so was able to get with my router N 300mbs speed!

  I found it on ebay for about $25 plus delivery charges. Oh and these cards are VERY easy to replace. There is a door on the bottom of the laptop with a captive screw - remove the door, then another screw which holds the card down. 2 drivers who commit on the 2 connectors on the map - the map out on the right.

  This card worked very well for me I highly recommend to solve the problem with shit card atheros 5007.

  Unfortunately, my laptop was stolen 2 weeks ago! (it was only 2 months old!) Some loser scumbag broke in with me so that I was at work and stole my laptop and my LCD 24 ''!

  I've had this laptop for $350 new Staples. I can't find a similar agreement now.

  Don't know if I'll go with HP\Compaq after what I went through just to make it work wireless...

• Vista will not connect to Netgear WPA/WPA2 wireless router

  HP Presario laptop with Vista Home Premium. Added Service packs 1 & 2 in a timely and all upgrades of MS Vista through 8/11. Laptop does not work on the wireless network using a new Netgear N300 router with WPA/WPA2-PSK security.  Roommate has Windows 7 on his laptop and connects very well. I thought that these Service packs were supposed to solve the problem of Vista-WPA? My laptop connects fine with the router if I use an Ethernet cable directly between the laptop and the router. NetGear argues that it is a matter of MS Vista. I missed a special fix?  Any suggestions?

  Hello

  I suggest you to follow the steps in troubleshooting section and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  You can also read these articles and check if it helps to resolve the issue.

  View and connect to available wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/view-and-connect-to-available-wireless-networks

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  I hope this helps.

• New S10 could not connect to the Netgear WGR641v8 wireless router

  All,

  Really frustrated with the nine s10 that I received this afternoon. All my other laptops are able to connect to the router Netgear wireless fine but this one. I could connect the s10 of unsecured networks of neighbors very well, so it doesn't seem to be a hardware problem. More compatibility issue with built in network card wireless Broadcom and Netgear chipset. I was able to connect to the local network with thin cable.

  Anyone have any better ideas? I updated latest firmware for the router. I think also got the latest version of the driver for the adapter. Where is the problem? I tried setting secured or unsecured (no password) for the router, no luck. I'm scratching my head right now.

  This is the first time ever, I have a new laptop failed on me. I contacted the customer service and the guy had no idea.

  Anyway, thanks in advance.

  The WGR641v8 has enabled ' Access List' (it limits the devices that can connect to only those network manually allow)?

  I have a Netgear DG834G or something like and a S12 (I think it was the same as the S10 (but not sure) WiFi adapter), once I'd added it is MAC to my list of access routers, I was able to connect without any problem (actually I use said WiFi connection right now).

  [edit] Also, check what encryption protocol you should use and what windows uses - he can't pick up the correct one to use and if the connection is a fail for this reason. [/ edit]