network interface card double deployment for Expressway EI

Similar Questions

• Unity and double network interface cards

  The unit works well with 2 network cards? Tips or tricks if you use 2 network cards? They are one of the subnets differnet 2. My voicemail ports are registered in CallManager, but on a different subnet from the CallManager is on. And this isn't the MAC for the NETWORK card that my license file is for.

  Two NETWORK adapters is supported only in a configuration Active / Passive with the unit. Both NICs must share the same IP address. 2 cards using NETWORK in an active scenario can cause audio one-way and MWI problems. Please see the links below for confirmation.

  Configuration and troubleshooting of network interface cards double for Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_tech_note09186a00801d1c56.shtml

  Troubleshooting Cisco Unity

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/prod_troubleshooting_guide_chapter09186a008015082b.html

  I hope this helps. If so, please indicate the position.

  Brandon

• HP Pavilion a6330f desktop PC: is it possible to update my Network Interface Card?

  Is it possible to replace and modernize the Network Interface Card that I have (10/100 Base-T Network Interface)?  If Yes, do you have a recommendation indicating what replacement card should I buy?  The network interface that I have now I cannot take advantage of very high speed that my internet provider (150mmps).  Thanks for your help with this... Mike

  You are welcome.  Thank you for the additional information.

  Here is a card that should work for you:

  http://www.Amazon.com/TP-link-TG-3468-1000Mbps-Gigabit-express/DP/B003CFATNI/ref=sr_1_1?ie=UTF8 & qid = 1420761130 & SR = 8-1 & Keywords = PCIe-x 1 + Network + Card

  Read the reviews to see what users say about it.  You should disable the network adapter before you install it.  There is a PCI slot and the PCI Express x 1 slot is faster.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• How many switches must be configured and min no network interface cards?

  Hello

  We will implement the ESXi5.0.

  We would like to know if we use different ports for network management and vMotion groups?  It seems that two of them use the same (different from ESX 4) IP address.

  In addition, my supervisor would like to know what is the minimum number of network interface cards to use (because the server has no slot PCIe)?

  Your opinion is requested.

  Thank you

  TonyJK wrote:

  Since we implement VLANS on our site and based on the documentation, ESXi 5 gets only 1 battery IP, wonder what is the best way to cope.

  It is true that ESXi has that one battery IP, which is very good compared to the other two in ESX (Linux in the Service Console and the Vmkernel). However, we have only an IP stack means that it is the same driver tcp/ip, but does not mean that we cannot have multiple IP addresses.

  For example, you can create a Vmkernel how many interfaces you want and assign different IP addresses, which could be on the same network or on different.

  Even if you don't have a VLAN in your environment I would still recommend using another IP network for vMotion for your management. This will make the two a little more 'best practice', easier to different and you would be good too preperred if you implement VLANs in the future.

• Load balancing across the NETWORK interface card

  Hello

  Our ESX Server's NIC six, two for SAN, one to the dedicated Service Console and three for the virtual computer LAN traffic. I noticed one thing look in the performance tab in VC, is that all LAN traffic seems to go on one of the three the NIC and the other two are practically inactive.

  If I look at the network configuration for the vSwitch those with three cards network, grouping of NETWORK cards is set for 'road based on the original virtual port code '.

  Can anyone advise how to get a more 'democratic' usage of the three NETWORK adapter?

  
  
  As seen on http://www.eqlforums.com !

  How many virtual machines you host? With the load balancing algorithm you have selected (default), traffic is balanced to the vNIC level (i.e. all traffic from a given vNIC always through the same bear). This is the case for all, but the IP hash algorithm, which requires you to 802.3ad static port aggregation on your pSwitch. In most cases, there is no need to worry about the use of bear - if it's a GbE NETWORK card, you're probably not close to push the limits.

  Ken Cline

  Technical Director, virtualization

  Wells Landers

  TVAR Solutions, a company of the Wells Landers group

  VMware communities user moderator

• Best design for the use of 8 physical network interface cards on a 5.1 ESXi host

  I have 8 physical network cards to work with on and 5.1 ESXi host using Enterprise Plus license.  I need to repair the following traffic:

  Management traffic

  vMotion traffic

  Virtual machine traffic (probably 2 natachasery will suffice for this)

  NFS traffic

  Won't fault tolerance.  Natachasery-how much should I dedicate to NFS, vMotion, and traffic management?  What failover policy I should use (active / active) (active / standby) for each?

  It is business more licensing and vSphere distributed switches are used.

  Thank you

  Yes, I would put the backup in the switch as well as management traffic and vMotion is they use vSS or vDS. The other option would be to reduce your vDS for NFS traffic of 4 natachasery 2 natachasery and then or to add to the existing vDS that contains management and vMotion VM traffic to add it extra bandwidth or create a new vDS with these 2 natachasery. But at the point of my original thought around creating a vDS is based on all of my bandwidth throwing together and then cut it but I want it and do not have to trade around natachasery after the fact. But there are so many different ways to achieve that is the fun part.

• How to use 4 x 1 GB for software iSCSI NETWORK interface card.

  Hello. I have a HP P2000 G3, with iSCSI connections 4 x 1 GB. I have 4 free 1 GB NIC on my 5.5 esxi server. IM wondering how I could put things upwards, so it would use iSCSI 4x1Go at the same time, so I would get a 4 Gbps to my SAN connection. Is this possible? I read something about iSCSI multi-trip and Port binding, but is all a bit confusing. It seems to me which is used for failover? I tried to put in place using a multipathing guide and got to the top and his display I 8 paths to my SAN, but it seems that a NETWORK adapter is used when considering my switch activity.

  Any help would be appreciated.

  Take a look at this blog post: http://www.virtualtothecore.com/en/howto-configure-a-small-redundant-iscsi-infrastructure-for-vmware/

• Best Design with 8 (4 x1GB + 4 10GB) physical network interface cards

  I'm about to deploy a new vSphere 5.1 (Enterprise license) environment and would appreciate a lot a little comments to some best practices and real-world experiences. For our cluster HA, we will use Dell R720 with Broadcom 5720 girls cards four ports 1 and 2 Intel X 520 DA connection to a Dell EqualLogic SAN PS6110XV (using the Extension Module from Dell for MPIO Multipathing).

  (Note: the iSCSI network will use two switches Dell PC8024F and the 'public' network will have two switches Juniper EX3300).

  I need to design best perf for HA, iSCSI, vMotion, and I would like to know tips for this design. Pls help me!

  Nice piece of Kendrick on this same track.

  Really a lot of ways to skin the cat

  http://www.kendrickcoleman.com/index.php/tech-blog/VMware-vSphere-5-host-NIC-network-design-layout-and-vswitch-configuration-major-update.htm

• MAC addresses of our network interface cards physical on the ESX host

  I asked a very interesting question.   What is the MAC address for each physical network cards within our ESX host.   Our host ESX3.5Update4 has 6 of them.

  I am able to ESXCfg allows to identify the vNIC but assimilates to the physical network adapters?   or, how can I find the MAC address of the physical network adapters?

  No, I mean there are additional MAC addresses that the switch can 'see '.  The service console interface have a MAC, and address that will be displayed if you run 'ifconfig', but vmkernel will not be displayed in this way, use "esxcfg-vmknic - l" to display this MAC address.  The virtual machine each have their own of the MAC you can get that from their configuration files, or the vi client.

  -KjB

  VMware vExpert

• A physical server with 2 NETWORK interface card using a virtual machine as IPS (transparent VM) and everything should work normally?

  Hello guys.

  Is there a diagram that I made, using for my self this question.

  

  As you can see, I have a physical server with 2 NIC I don't want to use a VM (with Snort) as IPS / IDS system for inbound traffic on the management of VLANS. Is it possible to use this VM in this way (as an IPS/IDS, VM with two NIC without any routing work?)? Maybe you have a suggestion, how can I achieve this, as easy as possible? Maybe you have an opinion, what OS unix system do I use?

  Thank you for your time and your answers. Any useful information is much appreciated.

  Yes, it should work. You need to look out for, it's that the 'outgoing' NIC is not connected to the same physical switch as the entrant and that there is no link between these two physical switches, because this would create a loop of layer 2 on the network.

  I haven't worked much with Linux, but I don't see that you would have a problem to find some Linux/Unix with the possibility to bridge two network cards and use some software IPS to inspect the traffic.

• Satellite L350 - Issus with built-in Network Interface Card?

  I am unable to connect by Satellite L350 laptop computer to the Internet or using wireless or wifi.

  laptop is unale to recognize any network. I tried to connect using my mobile broadband. Even this does not work.

  I had downloaded various deivers and upgraded. But Windows does not recognize the network.

  Any suggestions please?

  Thank you
  Rudra

  Hello

  WiFi or LAN connection works?
  Well you are sure that your modem or router WLan is configured correctly?
  You should check this first!

  If you are 101% sure that this router works and has been configured correctly, then you should check the configuration of the firewall on your laptop.
  Check to see if any other software that is installed on your laptop does not have the laptop to connect to the router.

  Then the card Wlan and lan card REGULARITY in Device Manager.
  Reinstall the driver Wlan and LAN driver if the two cards are not recognized correctly

• Graphics card double output for the motorway A58

  Hi guys,.

  Work just gave me a Lenovo A58 SFF and while I don't have the serial number, I don't know what follows-

  Lenovo ThinkCentre A58
  Small form factor
  Intel CORE 2 QUAD Q8400
  4 GB OF RAM
  Hard drive 320 GB

  The machine is used only for work (spreadsheet, processing and internet) and I would like to run two monitors (both with VGA, PCI and HDMI inputs), but Lenovo A58 LTS offers only one VGA output.

  I did a quick search for graphics in this forum, but suggestions seem to be a little out of date as the machine is a bit long in the tooth now.

  As I work for a small business, we do not have a 'IT Department', so it is left up to me to sort.

  If you could please provide me with some options, it would be much appreciated.

  Thank you

  Chris.

  (1) the onboard graphics on the A58 can support 2 monitors. The card is in fact the second connector for the integrated graphics card.

  (2) limitation is that to do with graphics performance, you can not play on it. But Office apps will work fine. normal movies will work as well.

  (3) it's a true second monitor, you can expand the view to make both monitors independently managed.

• Creation of Win8pro, 32-bit NETWORK interface card

  My host is Windows 7 Pro 64-bit workstation running 9.

  I have a virtual of Win8 Pro, 64-bit, with NIC but my VM Win8 Pro work, 32-bit machine, does not see any network adapter. Any help to work around this problem would be greatly appreciated.

  Welcome to the community,

  Thanks for posting (attach) the VM Windows 8 .vmx file or check if it contains

  ethernet0.virtualDev = "e1000e.

  If not, add this line, while the tab or VMware Workstation virtual machine is closed.

  André

• Transition network card, multiple network interface cards?

  Hello

  Just a quick question, does anyone know how I can fill more then 10 individual vm NIC to 10 Physics/loop back adapters? The reason why I ask, is that in the network editor it provides only 10 slots and no option to add more.

  I had a search around but unfortunately came up with nothing.

  Thanks for any info or pointers.

  The host Windows don't support 10 VMnets but a Linux host supports up to 255 VMnets.

  BTW, it's in the user manual.