New Deskjet F4185 All in One or any other printer Deskjet F4185 software needed, Pls!

Similar Questions

• Incredible problems to get the new workgroup C8180 All-in-one

  I bought a C8180 All-in-one printer to the end of September. When I plugged in and installed the software, everything seemed to function OK (I didn't test printing from the computer at the time), but after a short period of time to print Microsoft Word and Wordpad failed, started working and then failing again every time I reinstalled the software to try to solve the problem. Then began a long series of emails with HP technical support. In the next two weeks I have uninstalled and reinstalled the software 6 or 7 times in several different ways, under the instruction of HP. But he never could get Word and Wordpad works correctly. Finally, once again, under order of HP, he worked with a fake installation of HP Deskjet 990c printer. Then I noticed that it was more possible to digitize documents and slides to the computer, except by using a chip memory such as an intermediate storage. Then I went on vacation after spending about 30-40 hours two weeks previous emailing and calling the HP technical support.

  Back from vacation in the third week of October, I took the issue once again with HP support. Yet once, I spent hours and hours writing emails and reinstalling the software but to no avail. HP finally proclaimed this a problem difficult and said that it would increase the level of support. A gentleman named Sylvester who sent someone would phone a day pre-arranged to see more advanced techniques could be applied to the problem. Needless to say that the phone call came not despite my cancelling several meetings to wait in it (I should have better that they had promised to phone back me several times before and has never done).

  Finally, I called customer service to the local office of HP. (At least you can get to them without having to listen to the music for half an hour for the price of 5 p / minute.) They said that they would ensure someone would contact me and would monitor the call to ensure that happened. A week later I ' d has received no call, and I went to the local customer service. Has been raised to the top level of management, and finally, after a few reminders more than me, they managed to get a senior technician, called Natheem, in their technical service Cap to call me.

  He has been very helpful (and actually phoned me several times), and finally he forced me to go through the complicated process of getting Microsoft in India (via a conference telephone with Cape Town and myself - apparently it would have cost me a lot in telephone charges, but I have not had the Bill) to give advice on how to spend my Windows XP with service pack 2 and my internet explore to IE6. I reinstalled the C8180 software once again. No difference, still the same problems, except that now, Microsoft Word would work with the HP C8180 printer driver.

  At this point, Natheem said that it must be a hardware fault and arranged for the device must be replaced.

  The new unit arrived last Thursday. I again carefully uninstalled and reinstalled the software, connected to the machine and got the same problems, but once again with Microsoft Word cannot print with the C8180 printer drivers.

  I tried to contact Natheem again once in Cape Town this afternoon. After half an hour of expensive music additional I have with a person named Waleed who said that Natheem is on a call but he would get to call. No call came.

  So on the forum, I would like advice on what to do with a new HP C8180 All-in-One printer which:

  1. not print Word documents (except by using a printer deskjet 990c driver)
  2. used to scanning documents or transparent to the computer
  3. will not print photos from the computer using HP photosmart essential, or other photo editing software

  I'm also rather fed up of the assistance provided by HP. When you get through them they always try to help, but pass through, especially for someone who knows your case is more frustrating (and costs). In an attempt to get the thing, I also had to downgrade my computer Windows XP service pack 2 OS and my internet explore to IE6. I spent probably 50-60 + hours of the last two months, trying to get the thing work.

  Any advice on what to do next would be welcome.

  BobA

  Hi David,

  Well, my story has a happy ending. I stopped trying to untangle the printer after a whole month of working hours, including a lot of phone calls to the SA and responidng to dozens of emails. But then I bought my wife a laptop Toshiba for Christmas - and it worked perfectly first time. In any case, my computer was in a bit of a mess especially when the messing around I had done on this to HP support, so I decided to reload my operating system (after reformatting hard disk), I just finished. And guess what the C8180 works perfectly (at least until now anyway)! I just updated my OS to SP2 (according to HP support the C8180 has problems with SP3), and I kept my Internet Explorer version 6 (higher versions - 7 I think - again can cause problems according to HP support). I somehow use Firefox. But now its work, its quite an impressive machine.

  I want to say individual personnel in support of HP thin is always very friendly and helpful. It's just a phone, it costs and often listen to music for a long time, its very difficult to get hold of the same person again, if you spend hours to repeat the details of your problem, and despite vehement promises they call you rarely back - probably because they are too busy. His support system which is very poor, not the support staff.

  In any case you have a different problem. If your printer does not work on computers with different operating systems. I would say that you have good arguments to either get a new printer or your money under the guarantee.

  Good luck

  BobA

• New Canon MS216 all-in-one works very well (test prints work.) But it does not print some documents I send to her.

  Support Menu Ex driver is not installed. Do I need? I am running Windows 7 and that you have installed a new MF216 Canon all-in-one. It keeps switching me to fax or scan, when I want to do is print my computer USB connected articles.

  Hi Irma,.

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the number of full model of your printer?

  This problem may occur if the settings or device drivers are corrupt.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the printer Troubleshooter and check.
  Refer to this article:
  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  He made sure that a printer is connected to your computer, and it checks for common issues such as whether the printer has enough paper and toner to complete printing your document.

  If this does not help, use method 2.

  Method 2:
  Please use the suggestions provided in this Microsoft support article and check.
  Reference:
  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• I can't install my Adobe Acrobat 9 Pro in my new HP Pavilion all-in-one computer desktop drive, because my new HP does not insert the disc in a disc drive.  What can I do to fix this problem?

  I can't install my Adobe Acrobat 9 Pro in my new HP Pavilion all-in-one computer desktop drive, because my new HP does not insert the disc in a disc drive.  What can I do to fix this problem?

  Hi edwards39572619 ,

  Please visit this link to download Acrobat 9 Pro:-download Acrobat 8 and Acrobat 9

  Let me know how it goes.

  Kind regards

  Christian

• Printer all in one HP PSC 2175v prints the page number and the title of the document

  Printer all in one HP PSC 2175v prints the page number and the title of the document.

  This is the default value?  Can I disable this?  I would prefer to print only the document, without page numbers and the title.

  I was printing of either Wordpad specifications, using Windows XP.

  Using the front panel of the printer, I loaded the defaults of the printer, and that fixed the problem.

  Thank you

• MY DVD - RW DVR-112D ATA DEVICE IS ONLY PLAYBACK DVD VIDEO (EX MOVIES). BUT NOT READ ANY OTHER TYPE (E.G. SOFTWARE).

  MY DVD - RW DVR-112D ATA DEVICE IS ONLY PLAYBACK DVD VIDEO (EX MOVIES). BUT NOT READ ANY OTHER TYPE (E.G. SOFTWARE). Everytime I put a dvd movie it plays automatically, but any other type of cd it will say insert disk. One has had this problem?

  Hello

  You have disk problem as the CD/DVD is actually 4 discs in 1 case (burn CD & DVD and CD and DVD read).
  Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Several good info here:
  http://Club.myce.com/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ----------------------------------------------------------------------

  Step 1: Please make all underneath the same if you've done it before as it's often the total of the process which
  solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
  that the troubleshooter does not, and those who "could" be the cause.

  Check with your system manufacturer Maker and device for possible firmware updates and the good
  Your player registry entries.

  Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
  other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
  a person with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• DeskJet 2050 all-in-One - J510: how to print without borders?

  I try to print my project on paper to A4 borderless, but it seems that no matter how to change settings, the results still had a border. Can someone give me some advice on how I could solve this problem?
  
  I print on Word, and my printer is HP Deskjet 2050 all-in-One - J510a.

  Hello.

  The deskjet 2050 printer does not support printing without margins, as you will find by notebook loads below:

  Without borders: No.

  http://h20195.www2.HP.com/v2/GetPDF.aspx/4AA1-1465EEE.PDF

  This material allows to print only to a certain margin.

  The lower border is 0.57 ", the top border is 0.06 'and the left and right borders are 0.125. any impression beyond these margins is cut off due to the limitations of harware.

• Cannot connect my new HP4620 wireless all-in-one printer on my local network

  The printer is aHP 4620 all-in-one wireless printer.  The network is a Linksys Wireless - G Broadband Router connect an old HP Pavilion zv6000. portable 32-bit laptop running Windows XP and my brand new Pavilion dv6-7010us 64-bit running Windows 7.

  First of all, I ran the installation disc for the printer on the Pavilion zv6000.  Wireless Setup went well without any problem the printer connected to the router and to enable printing of thezv6000...  Then, I loaded the printer installation disc in the new Pavilion dv6-7010 and started the installation.  Everything went well until what the installer told me to connect the USB cable between the printer and the computer, and shortly there after that I got an error message an unknown error and that the installation program has been stopped.

  Since then I ran, I think, all the trouble shooting programs recommended with different results, all unsatisfactory.  Right now the test of the last wireless network said that the wireless is on, the wireless works. The connected test did not run.  the major flaw is that the SSID was not found, but there were 5 other networks detected.   The current configuration is: SSID is not set, the Mac address is OK, No IP address is defined, mode of Communication is Infrastructure and Authentication Type is open system.

  Printer is no longer printing of thezv6000.  However the zv6000 both my IPAD become jobs printed via

  HP eprint.  It does not appear that there is something wrong with the printer mainly a configuration problem.   Any suggestion would be

  greatly appreciated.

  Hi Beelzebub2,

  Follow the steps outlined in the document below and let me know what you find?

  "Cannot find the printer" error message on the computer during a wireless network Installation

• DeskJet 2542 all-in-one: parse error message prints well

  I kept getting this error trying to scan a document for the first time.

  "An error occurred all in communicating with the device. Please check that the device is correctly connected and powered. »

  To make sure that the printer is connected I printed a pdf on file on the computer and managed.

  I installed from the given CD and I intalled software on the HP site that grew to my specific operating system OS X 10.9.  I checked my firewall and allowed him to be opened for printer sharing.  I restarted my modem wifi network, I restarted the computer, and I restarted the printer.  I have reset my printers and reselected this printer... which is the only printer that was available for selection.  The computer recognizes the printer completely, however it just keeps giving me the message quoted above for scanning.

  Help, please.

  Hello @Elochin and welcome to the Forums of HP!

  I understand that you are having problems of scanning.  I would like to help!

  You have problems, make a copy?

  I have a few steps, I recommend you:

  I suggest to remove the printer from your printing system, using this document: uninstalling the software of the printer.

  Once you have deleted, I suggest to check and repair disk permissions: function to fix the permissions of all utility disk drive.

  I also run your Apple updates: OS x: Mac App Store apps and OS X update

  After the updates, I recommend reinstalling the HP Deskjet 2540-All - in - One Printer full feature software and drivers series.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• Pavilion all-in-one Q214 23: factory restore on the new HP Pavilion all in one computer

  I have a week 6 old Pavilion Desktop all-in-one.  I wanted to do a factory install on it because I had a lot of extra things that I don't want anymore, I installed and I thought what a factory restore would be better.  I went to the HP Recovery Manager and no where in the choices he said 'factory restore '.  He used to have this option in the HP recovery environment.  I checked all the options and nothing on the factory restore.  I made a set of recovery discs, but I always remember that HP still had the opportunity to do a factory restore.  I have tried F11 and F8 and no luck.

  Answers or suggestions will be greatly appreciated.

  Hello

  Thanks for posting in the HP Support forum. Welcome!

  According to the model of the computer, it can not be called exactly the HP system recovery but if your computer is originally shipped with Windows preinstalled 10, recovery partition must be present.

  S ' Please, first manually copy your imporant most of the data on an external partition

  -Follow these instructions here to open the collection from inside Windows

  > > http://www.tenforums.com/tutorials/4130-reset-windows-10-a.html

  > > http://www.tenforums.com/tutorials/4130-reset-windows-10-a.html#option2

  'S called it Reset - Windows Reset with options to RESET the machine as long as the plant (remove all), with an option to "freshen up" Windows and keep personal files.

  Let me know how it goes and if it works for you.

• HP 7210 all in one - will not be printed on the fast project configuration

  For the last two weeks, my 7210 HP all-in-one has decided that he does not want to print on quick project more.  I have the default settings of the printer on quick project, and I even went and edited individual documents to ensure that they are on the quick project, but it still prints on quality.  I do a ton of printing on a daily basis, and that is to kill my ink, not to mention how long it takes.  My OS is Windows 7, 64-bit.

  Hey @kmh1883,

  Thanks for getting back to me on this subject "fast draft" with your HP Officejet 7210 all-in - One Printer. Even if printing HP and doctor Scan found no problem, it seems that you may have a driver conflict. I would like to try another driver at the moment to see if this clears up your printing problems.

  How to add another driver:

  1. Click on the Start menu
  2. Select the devices and printers
  3. In the devices and printers folder right click on your HP Officejet 7210 and left-click on properties of the printer
  4. Left click on the Advanced tab
  5. Left-click on new driver
  6. When the new driver window just press 'Next' until you see a list of manufacturers on the left and a list of Printers on the right.
  7. Select HP as the manufacturer on the left
  8. DeskJet 9800 select the printer on the right. If Deskjet 9800 is only select "Windows Update" at the bottom left and once the update has been completed, you will be able to select Deskjet 9800.
  9. After selecting Deskjet 9800 hit next complete the new driver Wizard
  10. Under the printer properties window, select 'Apply' but do not hit OK
  11. Select the general tab
  12. Rename your printer in HP Officejet 7210
  13. Click OK
  14. Finally, right click on your HP Officejet 7210 one more time and left-click on Printing Preferences
  15. Left click on the paper/quality tab
  16. Left click on the drop down menu 'Normal' for quality printing at the bottom right and change its project of Fast
  17. Press apply and OK

  Test print from the print driver Deskjet 9800 replacing to check if the setting "Fast Draft" remains.

  Please let me know if this solved your problem. Good luck!

• 2510 all-in-one: 2510 used color printing

  Hello

  My printer has recently decided not to print in color.

  It copies in color

  New HP color cartridge

  Doctor says no problem

  Print Preview in Powerpoint slides & White; shows black Word displays the preview before print in color, but print in B & W

  When I go to print preview options it show a printer B & W only

  Hi @Mandolin456,

  Welcome to the Forums of HP Support!

  I see you are having problems printing in color for the all-in-one printer HP Deskjet 2510.  I will definitely do my best to help you.

  I understand that you are in color copy, printing and a doctor Scan is no problem.  I suggest that we take a glance in the printing preferences in the print to the printer settings.

  I would like to try the steps in this guide, HP Deskjet, Officejet and Photosmart printers and all-each change of printing in Windows settings 8

  Change the settings for printing a single print job

• HP psc 2355 all-in-one: PSC 2355 all-in-one scan, but not print

  The printer was purchased at a garage sale may be a few years back. It scans perfectly fine, but it will not be printed. I tried searching the Web for drivers and uninstalling/reinstalling it, even the installation under another pilot as series 2300. The closest driver that appears is 2350 series. Windows Update crashes when I try to get to find the drivers more.

  Print a test page once, he hasn't done anything since then except to give me errors on the printer LCD. I have only a black cartridge in it because I don't need color, but I doubt that's the issue.

  From the looks of things, this is a common problem... I saw a post where someone has too, but nothing has worked.

  I am running a computer portable 64-bit windows 7, home premium and USB connection.

  Hey @TKStall,

  Thanks for getting back to me with the error messages.

  The value 0 x error messages you see on the screen of your PSC 2355 all-in-one indicate a hardware failure in your printer ink system. Because the errors seem to be intermittent at the moment it is you may chance using your printer for a little longer. However, there is a hardware failure occurring within the printer and for this reason, there is a chance that your printer may stop working at any time.

  Troubleshooting steps for error 0 x can be found here. But, as you can see one troubleshooting step is to perform a power reset on the machine. If the power reset does not clear the error state that a replacement of the entire unit would be necessary.

  Try to install your printer using the driver PSC 2350. However, if the error messages continue to appear on your printer, I would recommend reaching out to the Technical Support queue by phone about the options for replacement of material. Due to the age of your printer, you may have the option to update your PSC device for a newer model at a reduced price.

  HP Technical Support can be reached at the: 800-474-6836.

  If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  Worldwide contact HP

  It has been a pleasure to work with you. I wish you good luck going forward with this!

• All-in-one HP Envy 4500: printing a Web page

  The procedure to print a web page has changed all of a sudden.

  Until today, it's simple. I clicked on the print icon in the bookmarks bar. This launches the print dialog box. I then clicked on 'Préférences' to select the print quality and finally on 'print '.

  Today, I wanted to print confrmation of a command line. When I click on anything that is in the print dialog box, another window open.

  I managed to select my printer, but when I clicked 'Print' nothing happened. In addition, I could not any setting beyond the number of copies and if you want to print on one or both faces. What is going on?

  Hi @hbf1842,

  What is the new name of the printer now listed as default printer in devices and printers? (Like 4500 or class envy 4500)

  If the class driver is installed, it would be a preinstalled Windows driver and it should not the automatic option to duplex. You will need to remove and add the urge to 4500.

  If you still experience problems, uninstall and reinstall the printer software again.

  • Uninstalling the software of the printer (Windows).
  • HP ENVY 4500 e-all-in-One Printer series full feature software and drivers.

  The HPePrint driver is automatically installed with Windows 8. Just make sure that it is not selected as the default printer in the future.

  Thank you!

• OfficeJet Pro 8600 all-in-One connected as network printer loses connection

  In December 2011, I bought a HP Officejet Pro 8600 all-in-One to replace an Officejet 6500 as my network printer home. The 6500 worked very well on my cable, but his screen did not, I tried some of the features offered by the 8600 and I got a good price on a new warehouse of BJ. I have the 8600 connected via ethernet (not wireless), with a static IP address. All my computers on the network are running Windows XP Pro SP3 and are up-to-date with Microsoft updates. However, from one day to the next my 8600 will lose connectivity scan (Scan of the computer shows it as being disabled on all my computers at the same time, and I can't reconnect), and if I do not have anything he'll (as in a few hours) also lose connectivity impression. The only way to restore connectivity is to uninstall the HP Officejet Pro 8600 device software basis of all computers, and then reinstall the printer. I had a phone conversation and two debates with HP Technical Support; They suggested that the problem is in the firewall on the computers (but if that were the case I don't think that the loss of connectivity would occur on all computers at the same time), the IP address setting (doesn't make sense) and the printer driver is not not the latest version. I tried all the suggestions, and none of them have solved the problem. The last counselor "has raised the issue to the next level", which proved to be a Manager with no technical expertise and his only suggestion was that I have to return the printer to the merchant. I think the problem is the firmware in the printer (which, according to the 'update' on the printer option, is the latest version). Any other suggestions or experience?

  After a lot of research and find the settings that I did not know that Windows XP offered, I found that the following appear to have solved the problem I've known - at least the printer is now operational for more than 48 hours without losing printing or scan connection. Here are the steps I used:

  1. Start Control Panel  connections network and Internet

  2. Choose "network connections."

  3. Right click on "connect to the Local network.

  4. Choose "Properties".

  5. In the top window is the name of the Ethernet computer connection port, select "Configure" next to this window

  6. Select the tab labeled 'Power Management'

  7. Uncheck the box "allow the computer to turn off this device to save power".

  8. Select the "Advanced" tab

  9. Select the entry "power saving Mode".

  10. If this entry is set to change 'On' to 'Off '.

  11. Select 'OK', and then close the windows that were opened