New local VIRTUAL, guest network cannot Ping GW

Similar Questions

• Cannot ping between virtual servers on the same host

  I have a 5 ESXi host with 3 virtual copies of Windows Server 2008R2 running on them. The ESXi host is connected to my switch, which has the Windows 2008 R2 DC to my test network and my laptop management with VSphere branch above as well. I can ping host, mobile and ad server of each of the individual virtual servers and can ping and RDP for all 3 from other devices not on that host, but I cannot communicate between the three. I have Windows Firewall disabled on all three. I have no firewall, and all machines have an IP address in the 10.0.0.X range I deleted then recreated the only virtual switch on the host on which appear all 3. I've been VERY frustrated for the last 3 days on it. Why my virtual machine cannot talk to each other?

  When you have registered virtual machines in ESX you selected moved VM or Coiped VM? Go to editing parameters and watch the MAC addresses. My guess is that if you copied power (including the vmx files) then the MAC address is the same for all virtual machines. You can stop the machine and change for a MAC address mac address. You can also remove the network adapters, one of each, and then add the new network cards. Remember to reconfigure the IP addresses on the box and remove the ghost network maps after doing this.

  Check this KB to change the mac address.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=507

  Also, can you connect to the switch and look at the ARP table and see if the system VMs register here.

• Cannot ping a virtual machine, except on the host computer.

  I have a host of SuSE, built on a chassis of IBM. It has a link for the failover interface. It has an IP of 10.10.138.196. SM 255.255.255.128. DG 10.10.138.129. I can ping this machine without problem. On that note, I have a virtual machine of SuSE. It has the same mask and gateway with an IP address of 10.10.138.197. It can ping the host (196) and the host can it ping. However, he cannot ping to the gateway by defaut.129. He receives a message Impossible to its own virtual interface. I have installation bridged networking early with no luck.

  I tried to change the DG on the guest a.196. I have installation routes by default, and specific directions to 10.10.138.129 on the host and the guest without success. I talked to a few colleagues and they are not of course either. I need this available, so it can be used for a variety of applications.

  You will not see a virtual NETWORK adapter for bridged interface, only for NAT and the host-only networking. There will be a device/dev/vmnet0, but that is not actually used to fill itself.

  Your problem is that your bridged interface is bound to the wrong card on the host: it must be related to "bond0" not "eth0". You will need to re - run /usr/bin/vmware-config.pl to address which forces all running VMs to be stopped.

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Cannot get SW1 to the second network of ping and can't get the HQ router to ping SW1.

  Hello the forum community.  I am new to Cisco Configuration and cannot understand why, in the attached packet tracer file, I can't have my SW! switch to ping to the gi0/1 interface of the branch office router and beyond.  I also can't understand why I can ping to the gi0/0 interface on the router in the branch office router HQ, but cannot ping the switch SW1 and beyond.

  Ideally, I'm trying to configure the network so that PC1 can ping 172.16.1.100, which is a loopback on router HQ.  I ping the closure of the branch office router, but not the switch SW1.  I cannot ping the gi0/1 interface on the router of the branch of the SW1 switch and do not understand why.  I can also ping the gi0/0 interface on the router in the branch office router HQ, but cannot ping the switch SW1 of the HQ router.

  PC1 - 10.1.1.100 255.255.255.0

  SW1 - VLAN 1 - 10.1.1.11

  Branch gi0/0 - 10.1.1.1 255.255.255.0, gi0/1 - dhcp assigned as 209.165.201.1 255.255.255.224, dynamic NAT activated with access-list 1 (permit 10.1.1.0 0.0.0.255), the pool name is NAT_POOL with the address range of 209.165.201.5 - 10 255.255.255.224 as NAT address range.  I can see it working with debug ip nat active when I ping the router address 10.1.1.1 HQ, although I have test the ping without NAT and it is always successful.  Gi0/0 inside the nat, g0/1 outside the NAT.

  HQ gi0/0 - 209.165.201.2 255.255.255.224, dhcp server enabled to provide an address for the router in branch gi0/1.  I had to add a static ip route 10.1.1.0 0.0.0.255 209.165.201.1 in order to be able to get the ping to the router HQ to branch router gi0/0 to work.  Don't know if there is a better way to do it, but it's the only way I could make it work so far.

  You will need to rename the .txt file, attached to. pkt.

  Thanks for any help!

  Hello

  The switch has ip routing enabled, if so disable it and give it a default gateway instead

  no ip Routing
  IP default-gateway x.x.x.x

  RES

  Paul

• ASA VPN cannot ping ip local pool

  Hello

  We have ASA 5510 a device be deployed for a period of time. Everything works fine except customers local VPN cannot ping local customer VPN which get their IP address to the local swimming pool. They can ping anywhere on the local network of company, but not each other. I don't know there's a logical explantion for this because of an ACL but all appreciated the advice...

  Thanks in advance

  Keith

  Hi Keith,

  I think that, in order to allow a customer VPN reach another VPN client, the SAA should turn the VPN traffic (because it will receive the traffic of a VPN tunnel and re - again to send another tunnel.)

  Can you add "same-security-traffic intra-interface permits" and try again?

  Federico.

• Cannot ping virtual machine Windows 7 vm Server 2012 [Server R2 2012]

  Hi all

  I'm not sure that this is a vmware workstation or server 2012 r2 problem, but I would still ask thought.

  I have a 2012 r2 vm server and win 7 vm in a ' host-only: a private network, shared with the host country "network connection.

  I can ping the server vm win7, but cannot ping the ""Server the VM win7 ". "

  But when I point the win7 dns on the server 2012R2 (that has AD and DNS configured) I can join the virtual machine Windows 7 announcement.

  Its totally weird

  Whenever I try to win7 from the ping server, it says "Request Timed Out".

  Does anyone know how can I fix?

  I'm using VMWare Workstation 11

  Thank you

  Post edited by: Michael Hilburt

  Is there a way to get pings without demeaning the whole firewall?

  https://TechNet.Microsoft.com/en-us/library/cc972926%28V=WS.10%29.aspx?f=255&MSPPError=-2147217396

• Cannot ping new addresses IP vmkernel

  I created a few exchanges of vmkernel iSCSI in new bond for our 10G storage on a new vSwitch but I can't ping the IP addresses assigned to them (10.1.45.187 and 188). I have the same setup on a different host and it works very well. I swapped the connections on the 10G switch with those of the host of work as well as cables, so I know it isn't a switch port, the switch config issue or the cable. I even swapped the IP with the work those just to make sure.

  But if I SSH to another host on the same network I can ping those IP vmkernal addresses I can't from my desktop. I can also ping vmkernel IP addresses on the host of my office work that is on the same subnet as the host of non-working. I cannot ping the vmkernel IPs of a host on a different subnet, but can ping ports vmkernel work of host to a host on another subnet.

  I don't know that it's just something simple that I'm missing... I hope!

  Don't ask me why I have not found this before, but here's the answer to my question. I can give me points?

  VMware KB: Ping ICMP in 5.1 and 5.5 ESXi ESXi response behavior change

• Cannot ping the Virtual Machine by host

  Hi all,

  Please help, I use VMWare Workstation 6.5 and I have a physical operating system which is Windows XP SP2, I have a network card, but not connected to a physical switch, the IP address is 192.168.0.1. I installed a Virtual Machine using Microsoft Windows 2003 server as the operating system, promote as domain controller, install the DHCP, DNS service and assign an IP 192.168.0.2, no default gateway.

  My VMnet1 on physical operating system has an IP 192.168.204.1 and VMNet8 has an IP 192.168.126.1.

  The host, I cannot ping the 192.168.0.2 which is the IP address of the Virtual Machine. Even in the Virtual Machine, I can not ping 192.168.0.1 is the IP address of the host. From what I read, the physical and the virtual machine were connected with a virtual switch. Am I wrong?

  Any advice?

  Thanks in advance.

  They SEEM to be in different networks, you need search routing between them,... since they differnet networks...

  on the other

  they do host and the virtual machine on the same subnet / network for EXAMPLE: class C class network 192.168.200.0/24

  granting of points if my answer was helpful... Thank you > > > > > > > >

  concerning

  Joe

• Router and Switch cannot ping each other

  Hello

  I just build a lab at home.

  In my current lab, I have 2 SW and 3 the router.

  I have a problem, I do not know what Miss me in my config. My router cannot ping my SW.

  and I also want to change my LAN from VLAN 1 interface connection at 30 of VLAN... but when I configure the VLAN 30 he show me line is in PLACE but the Protocol is DOWN.

  Another question, if I want to create a VLAN with a different address, what should I do?

  for example

  VLAN 10 > 10.10.10.1

  VLAN 20 > 20.20.20.1
  etc...

  interface Vlan1 description LAN ip address 10.10.10.1 255.255.255.0 secondary ip address 30.30.30.1 255.255.255.0 secondary ip address 40.40.40.1 255.255.255.0 secondary ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!

  Here's the conf for my RT. ROUTER > 877SW > 2950 24 WS

  CISCO_877#sh runBuilding configuration...
  
  Current configuration : 3468 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname CISCO_877!boot-start-markerboot-end-marker!enable secret 5 $1$.ISW$71jzJ0Or0nenXZd/8D8.x/!no aaa new-model!!dot11 syslogip cefno ip dhcp use vrf connectedip dhcp excluded-address 20.20.20.0 20.20.20.30!ip dhcp pool LAN network 20.20.20.0 255.255.255.0 domain-name SYS.local default-router 20.20.20.1  dns-server 202.123.2.6 202.123.2.11  lease 0 4!!!!!username admin privilege 15 secret 5 $1$A1V4$GR9sPtPVXDRoOiDKRtC1M1! ! archive log config hidekeys!!!!!interface ATM0 description (OUTSIDE)ADSL_WAN no ip address no ip redirects no ip unreachables no ip proxy-arp no atm ilmi-keepalive pvc 8/35  encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto !interface FastEthernet0!interface FastEthernet1 dot1q tunneling ethertype 0x9100!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description LAN ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!interface Vlan30 description LAN no ip address no ip redirects no ip unreachables no ip proxy-arp shutdown hold-queue 100 out!interface Dialer0 description WAN_OUTSIDE ip address negotiated ip mtu 1498 ip nat outside ip virtual-reassembly max-reassemblies 1024 encapsulation ppp ip tcp adjust-mss 1400 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname [email protected]/*  */ ppp chap password 7 071C385F5C001D0403 ppp pap sent-username [email protected]/*  */ password 7 120A1C04000208053E ppp ipcp mask request ppp ipcp route default ppp ipcp address accept!ip default-gateway 20.20.20.1ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0ip route 10.10.10.0 255.255.255.0 Vlan1!no ip http serverno ip http secure-serverip nat inside source list 110 interface Dialer0 overload!access-list 110 permit ip 20.20.20.0 0.0.0.255 anyaccess-list 110 permit ip 10.10.10.0 0.0.0.255 anyaccess-list 110 permit ip 30.30.30.0 0.0.0.255 anyaccess-list 110 permit ip 40.40.40.0 0.0.0.255 anyaccess-list 110 permit ip 50.50.50.0 0.0.0.255 anyaccess-list 110 permit ip 60.60.60.0 0.0.0.255 any!!!control-plane!banner motd ^C
  
  :'######::'##::::'##:'########::'######::'##::::'##:'##... ##: ##:::: ##: ##.....::'##... ##: ##:::: ##: ##:::..:: ##:::: ##: ##::::::: ##:::..:: ##:::: ##:. ######:: #########: ######:::. ######:: #########::..... ##: ##.... ##: ##...:::::..... ##: ##.... ##:'##::: ##: ##:::: ##: ##:::::::'##::: ##: ##:::: ##:. ######:: ##:::: ##: ########:. ######:: ##:::: ##::......:::..:::::..::........:::......:::..:::::..::
  
  ^C!line con 0 no modem enableline aux 0line vty 0 4 password 7 xxxx login!scheduler max-task-time 5000end
  
  CISCO_877#

  And this is for my SW

  CATALYST_2960_01#sh runBuilding configuration...
  
  Current configuration : 5166 bytes!version 12.1no service padservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname CATALYST_2960_01!enable secret 5 $1$MGrN$PtHgL3KfH0vy7Mr1Fo0hF.!ip subnet-zero!ip ssh time-out 120ip ssh authentication-retries 3vtp mode transparent!!spanning-tree mode rapid-pvstno spanning-tree optimize bpdu transmissionspanning-tree extend system-idspanning-tree vlan 1-4093 priority 16384!!!!vlan 10 name ADSL!vlan 20 name GUEST!vlan 30 name MANAGEMENT!interface Port-channel1 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate spanning-tree cost 1!interface FastEthernet0/1 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/2 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/3 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/4 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/5 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/6 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/7 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/8 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/9 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/10 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/11 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/12 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/13 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/14 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/15 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/16 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/17 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/18 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/19 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/20 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/21 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/22 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/23 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface Vlan1 ip address 20.20.20.2 255.255.255.0 no ip route-cache!interface Vlan10 no ip address no ip route-cache shutdown!interface Vlan30 no ip address no ip route-cache shutdown!ip default-gateway 20.20.20.1ip http server!line con 0line vty 0 4 password 7 xxxx loginline vty 5 15 login!!end
  
  

  Thanks in advance.

  Eliane,

  Please remove the etherchannel port f0/24 of the switch configuration and store it in the trunk.

  interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active  <<< Remove this 

  Configure f0 on the router as trunk I think has 877, a switchport which fe interfaces are a part of. To display the corresponding Lass on the router, that you need to configure the VLANS corresponding on the router, then only the Lass will be in a State of going / up otherwise it will be in a down state. See if that helps. Thank you, hyacinth

• VPN - cannot ping the next hop

  Then some advice... I have configured a server VPN - pptp on my router, create a vpn for the customer at the site. For the moment, the client computer can connect and a connection to the router. I can ping from client to the router (192.168.5.1) but cannot ping 192.168.5.2 (switch) or 192.168.10.X (workstations)

  What I try to achieve is to access the internal network (192.168.10.X), which is the end of the layer 3 switch. Any help/extra eyes would be good.

  Here is my design of the network and the config below:

  Client computer---> Internet---> (1.1.1.1) Cisco router (192.168.5.1) 881---> switch Dell Powerconnect 6248 (192.168.5.2)--> Workstation (192.168.10.x)

  Router Cisco 881

  AAA new-model

  !

  AAA of authentication ppp default local

  !

  VPDN enable

  !

  !

  VPDN-group VPDN PPTP

  !

  accept-dialin

  Pptp Protocol

  virtual-model 1

  !

  interface FastEthernet0

  Description link to switch

  switchport access vlan 5

  !

  interface FastEthernet1

  no ip address

  !

  interface FastEthernet2

  no ip address

  !

  interface FastEthernet3

  switchport access vlan 70

  no ip address

  !

  interface FastEthernet4

  Description INTERNET WAN PORT

  IP [IP EXTERNAL address]

  NAT outside IP

  IP virtual-reassembly in

  full duplex

  Speed 100

  card crypto VPN1

  !

  interface Vlan1

  no ip address

  !

  interface Vlan5

  Description $ES_LAN$

  IP 192.168.5.1 255.255.255.248

  no ip redirection

  no ip unreachable

  IP nat inside

  IP virtual-reassembly in

  !

  interface Vlan70

  IP [IP EXTERNAL address]

  IP virtual-reassembly in

  IP tcp adjust-mss 1452

  !

  !

  !

  interface virtual-Template1

  IP unnumbered FastEthernet4

  encapsulation ppp

  peer default ip address pool defaultpool

  Ms-chap PPP chap authentication protocol

  !

  IP local pool defaultpool 192.168.10.200 192.168.10.210

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy inactive 600 life 86400 request 10000

  !

  overload of IP nat inside source list no. - NAT interface FastEthernet4

  IP route 0.0.0.0 0.0.0.0 [address IP EXTERNAL]

  Route IP 192.168.0.0 255.255.0.0 192.168.5.2

  !

  No. - NAT extended IP access list

  deny ip 192.168.0.0 0.0.255.255 10.1.0.0 0.0.255.255

  IP 192.168.0.0 allow 0.0.255.255 everything

  VLAN70 extended IP access list

  ip [IP EXTERNAL] 0.0.0.15 permit 192.168.10.0 0.0.1.255

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq smtp

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq www

  permit any eq 443 tcp [IP EXTERNAL] 0.0.0.15

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq field

  permits any udp [IP EXTERNAL] 0.0.0.15 eq field

  list of IP - VPN access scope

  IP 192.168.10.0 allow 0.0.1.255 10.1.0.0 0.0.1.255

  Licensing ip [IP EXTERNAL] 0.0.0.15 10.1.0.0 0.0.1.255

  WAN extended IP access list

  !

  Layer 3 switch - Dell Powerconnect 6224

  !

  IP routing

  IP route 0.0.0.0 0.0.0.0 192.168.5.1

  interface vlan 5

  name "to connect to the Cisco router.

  Routing

  IP 192.168.5.2 255.255.255.248

  output

  !

  interface vlan 10

  "internal network" name

  Routing

  IP 192.168.10.1 255.255.255.0

  output

  !

  interface ethernet 1/g12

  switchport mode acesss vlan 5

  output

  !

  interface ethernet 1/g29

  switchport mode access vlan 10

  output

  !

  Hi Samuel,.

  I went through your configuration and picked up a few problematic lines...

  First of all, you can't have your vpn-pool to be in the range of 192.168.10.x/24, because you already have this subnet used behind the switch (this would be possible if you had 192.168.10.x range connected directly to the router). In addition, you may not link your virtual model to the WAN ip address, it must be bound to an interface with a subnet that includes your IP vpn-pool range.

  The cleaner for this is,

  Create a new interface of back of loop with a new subnet

  !

  loopback interface 0
  

  192.168.99.1 IP address 255.255.255.0

  !

  New vpn set up, pool

  !

  IP local pool defaultpool 192.168.99.200 192.168.99.210

  !

  Change your template to point the new loopback interface,

  !

  interface virtual-Template1

  IP unnumbered loopback0

  encapsulation ppp

  peer default ip address pool defaultpool

  Ms-chap PPP chap authentication protocol

  !

  All vpn clients will get an IP address of 192.168.99.200 192.168.99.210 range. And they will be able to get the router and up to the desired range 192.168.10.x/24 behind the router. Packages get the switch, then to the host. Host will respond through the gateway (switch)-> router-> Client.

  PS: Sooner, even if your packages arrive at the host, the host will never try to send the response back through the gateway (switch) packets because STI (hosts) point of view, the package came from the same local network, so the host will simply try to "arp" for shippers MAC and eventually will expire)

  I hope this helps.

  Please don't forget to rate/brand of useful messages
  

  Shamal

• Problem: Local with OpenVPN network Mode

  Hello everyone.

  I have a problem on the Local Mode with OpenVPN network.

  My VM is a domain system based that needs a connection to the domain and redirects to files.

  This virtual machine works very well in online mode. It's good for the execution of this virtual machine in local mode in my company.

  One day, I get out of my company and use OpenVPN to connect back. I find that I have a problem.

  After that I started my VM, I realized that the VM network is link to my REAL, not the one OpenVPN network. It cannot connect to the DC of my company. The IP address of this virtual machine is DHCP on my network REAL, not the VPN server.

  Is it possible to fix it?

  Thank you.

  What is interesting.

  Default local mode works in NAT mode, so if the host machine is connected to a virtual private network, the guest running in client Mode Local should also see this network.

  Couple of clarifying questions then we can dig deeper:

  1. Any chance, the system has been reconfigured in mode bridged force instead?  (there are registry/GPO settings for this)
  2. Where is made the VPN connection?  Before or after that the VM Mode is turned on?
  3. The VM really not accessing the VPN network or is it just failing to get DNS information, (for example if you have the full IP address of a machine that is accessible through the VPN, can you ping that even if you cannot resolve the name?
  4. If the VPN connection is made after the virtual machine is running, have you tried the experience of first manufacturing of the VPN connection, and then start the virtual machine?

  I ask #2, #3 and #4 because the NAT daemon can sometimes be a little less sensitive to the host networking changes you want - especially regarding the DNS lookups.  You can also experiment with restarting the VMware NAT service on the host once the VPN connection is made to determine whether giving it the kick it needs.

• No guest network connectivity

  Hello

  I'm definitely a newbie so please bear with me.

  I have just completed a new installation of ESXi 4. The host server has 1 NETWORK card that I have assigned a static ip address: 10.10.10.101 (255.255.255.0 subnet mask)

  I installed 2 virtual machines. A Windows 2008 with a static ip address: 10.10.10.102 (subnet mask 255.255.255.0) and a windows 2003 server with a static ip address: 10.10.10.103 (subnet mask 255.255.255.0)

  The server ESXi NETWORK card is connected to a switch which I also connected an other PC running windows XP (255.255.255.0 subnet mask ip address 10.10.10.2) on this machine, I run my VSphere client.

  OK, here's my problem:

  My XP machine I can ping the host ESXi NIC but I get no response from network adapters on the virtual machines. When I connect to each of the virtual machines I only ping the NIC ESXi host I can't ping the machine XP or the other guest. So bacically everything can ping the physical card on the ESXi host, but that's all. Virtual machines cannot ping each other and neither can they ping all machines on the physical network.

  My installation is completely standard, accepting all the defaults. A single virtual switch, a 'network of the VM' containing my two virtual machines, a "network Manangment" and a "physical map".

  Any help or advice would be much appreciated. If you need more let me know.

  Magic,

  First of all start by loggin on virtual machines and other machine to see if either may ping virtual.  I know you said that anything can ping the ESXi host adapter, but two virtual machines on the same virtual switch must be able to communicate with each other first.

  If they cannot ping each other, but they can ping on the ESXi host, I suspect that you have the Windows Firewall on.  You can disable this control panel or by accessing services and slaughter the Windows Firewall Service.

  Once, you can get the ESXi host and virtual machines to ping each other, then you can test the network outside the ESXi host connectivity.  Once again the XP machine can also have a firewall, so if you have the DNS server, the default gateway or something like www.google.com can be a better test.

  I hope this helps.

  Doug

  www.phdvirtual.com, manufacturers of esXpress

• NLB - two virtual machines can't ping eachother when on separate hosts

  Greetings,

  I've been running some tests with NLB on the different desks as recommended here:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006558 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006778 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  I found that Unicast works better in our network environment, but it is still a problem:

  In http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006580 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912690 & StateID = 0% 200% 2041454807

  He says: "since all hosts in the cluster have the same IP Address and the same MAC address, there is no communication possible inter-hote between the hosts configured in unicast mode.» A second NETWORK adapter is required for any other host communication. »

  However, even with a second NETWORK adapter the virtual machines cannot ping eachother when they are on a different esx host. When they are on the same host esx virtual machines can ping each other. Also, when they are on different hosts, so that a virtual machine cannot reach each other on their dedicated IP address, virtual machines can reach other when ping the second card NETWORK (the one without an informed gateway).

  For example, the next 2 guests are connected unicast:

  VM1 has 2 network cards, NIC1 = 172.18.18.41 with gateway (dedicated IP) and NIC2 = 172.18.18.43 without gateway / WLBS enabled.

  VM2 has 2 network cards, NIC1 = 172.18.18.42 with gateway (dedicated IP) and NIC2 = 172.18.18.44 without gateway / WLBS enabled.

  When on the same ESX host VM1 can reach VM2 on 172.18.18.42 and 172.18.18.44, and vice versa.

  When on ESX different hosts VM1 cannot reach VM2 on 172.18.18.42 but it can reach VM2 thanks 172.18.18.44. In this case VM2 cannot reach VM1 on 172.18.18.41 but can reach VM1 on 172.18.18.43.

  I followed and applied the settings recommended in this article: http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1556 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  I even tried the kb from microsoft as shown here: http://support.Microsoft.com/kb/898867 even if the virtual machines have 2 network cards, but of course that did not help either.

  Does anyone have an idea what is happening here?

  The fact that it works on the same host, but not on different hosts type advanced to a network within VMware issue.

  Thanks in advance,

  Bram

  It seems that ir can be a problem of IP routing, even with the hosts on the same subnet.  Make sure that your routing table that traffic on each that is to/from your mgmt that ips turns off your local management interface.  If it isn't, then update your routing table in order to.

  Or, you could try setting up your mgmt network cards on a different subnet from your IP NLB.  I suspect that this will solve the problem.

  JP

• Cannot ping Lan devices in Vlan

  Hello

  I looked for a solution to this for the week without success. I came across a Cisco C3560, which is used because of its ability of poe to power some Deskphones Voip. While the works of great poe, machines connected to the switch can only communicate with each other and don't can't ping or otherwise access any device connected directly to the router of the network.

  The Cisco switch is configured with a vlan and a default gateway, but nothing comes out by behind the switch. On connected devices can ping by default gateway (192.168.0.1 - a tp-link router), receive a lease dhcp from the router said successfully and can connect to the internet, but on the local network, nothing works. (unable to connect to the printer connetced directly to the router or other computers connected directly to the router.

  Any advice? I am new to cisco switches, don't know what I'm doing here. I'm just trying to get devices that are connected directly to the switch to communicate with devices connected directly to the router.

  Switch#show runBuilding configuration...

  Current configuration : 1528 bytes!version 12.2service configno service padservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname Switch!enable secret 5 {}{}{}{}{}{}{}{}{}{}{}{}!no aaa new-modelclock timezone UTC 2system mtu routing 1500ip subnet-zero!!!!no file verify autospanning-tree mode pvstspanning-tree extend system-id!vlan internal allocation policy ascending!interface FastEthernet0/1!interface FastEthernet0/2!interface FastEthernet0/3!interface FastEthernet0/4!interface FastEthernet0/5!interface FastEthernet0/6!interface FastEthernet0/7!interface FastEthernet0/8!interface FastEthernet0/9!interface FastEthernet0/10!interface FastEthernet0/11!interface FastEthernet0/12!interface FastEthernet0/13!interface FastEthernet0/14!interface FastEthernet0/15!interface FastEthernet0/16!interface FastEthernet0/17!interface FastEthernet0/18!interface FastEthernet0/19!interface FastEthernet0/20!interface FastEthernet0/21!interface FastEthernet0/22!interface FastEthernet0/23!interface FastEthernet0/24 switchport mode access!interface GigabitEthernet0/1!interface GigabitEthernet0/2!interface Vlan1 ip address 192.168.0.26 255.255.255.0 no ip route-cache!ip default-gateway 192.168.0.1ip classlessip default-network 192.168.0.0ip http server!access-list 1 permit any log!control-plane!!line con 0line vty 0 4 password XXXXXXXXX login length 0line vty 5 15 password XXXXXXXX login length 0!end

   Switch#show interface

  Vlan1 is up, line protocol is up Hardware is EtherSVI, address is 001e.bd27.c4c0 (bia 001e.bd27.c4c0) Internet address is 192.168.0.26/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 3 packets/sec 138534 packets input, 9472693 bytes, 0 no buffer Received 0 broadcasts (68 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 30296 packets output, 2248820 bytes, 0 underruns 0 output errors, 1 interface resets 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/2 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c484 (bia 001e.bd27.c484) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:56, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 46000 bits/sec, 37 packets/sec 5 minute output rate 582000 bits/sec, 71 packets/sec 1941044 packets input, 327622438 bytes, 0 no buffer Received 38375 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 30699 multicast, 0 pause input 0 input packets with dribble condition detected 3224783 packets output, 2069682884 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  FastEthernet0/4 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c486 (bia 001e.bd27.c486) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129069 packets input, 64947010 bytes, 0 no buffer Received 9953 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 600269 packets output, 45540585 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/6 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c488 (bia 001e.bd27.c488) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:50, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 32693 packets input, 4244428 bytes, 0 no buffer Received 9942 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 588460 packets output, 45003331 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/8 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48a (bia 001e.bd27.c48a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:30, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32694 packets input, 4243413 bytes, 0 no buffer Received 9934 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9757 multicast, 0 pause input 0 input packets with dribble condition detected 588485 packets output, 45009466 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/12 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48e (bia 001e.bd27.c48e) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:28, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32742 packets input, 4252075 bytes, 0 no buffer Received 9947 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9763 multicast, 0 pause input 0 input packets with dribble condition detected 588497 packets output, 45019272 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/13 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48f (bia 001e.bd27.c48f) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:13, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 148160 packets input, 73818106 bytes, 0 no buffer Received 9973 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9760 multicast, 0 pause input 0 input packets with dribble condition detected 599666 packets output, 49045070 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/14 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c490 (bia 001e.bd27.c490) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:05, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129165 packets input, 68409495 bytes, 0 no buffer Received 9982 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9773 multicast, 0 pause input 0 input packets with dribble condition detected 600283 packets output, 45551497 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/18 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c494 (bia 001e.bd27.c494) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:49, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 21000 bits/sec, 18 packets/sec 5 minute output rate 13000 bits/sec, 16 packets/sec 606386 packets input, 88151136 bytes, 0 no buffer Received 159883 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 55198 multicast, 0 pause input 0 input packets with dribble condition detected 941617 packets output, 308269004 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/20 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c496 (bia 001e.bd27.c496) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:54, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 1000 bits/sec, 1 packets/sec 5 minute output rate 1000 bits/sec, 2 packets/sec 515813 packets input, 87006769 bytes, 0 no buffer Received 21466 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 19952 multicast, 0 pause input 0 input packets with dribble condition detected 1858112 packets output, 1700009146 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/24 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c49a (bia 001e.bd27.c49a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 546556 packets output, 41182636 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  GigabitEthernet0/1 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 001e.bd27.c481 (bia 001e.bd27.c481) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 556000 bits/sec, 83 packets/sec 5 minute output rate 76000 bits/sec, 63 packets/sec 4457827 packets input, 3961330567 bytes, 0 no buffer Received 15028 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 11213 multicast, 0 pause input 0 input packets with dribble condition detected 3822373 packets output, 728132696 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  

  Switch#show vlan

  VLAN Name     Status         Ports---- -------------------------------- --------- -------------------------------1     default active    Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16                        Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24, Gi0/1, Gi0/21002 fddi-default act/unsup1003 token-ring-default act/unsup1004 fddinet-default act/unsup1005 trnet-default act/unsup

  VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------1 enet 100001 1500 - - - - - 0 01002 fddi 101002 1500 - - - - - 0 01003 tr 101003 1500 - - - - - 0 01004 fdnet 101004 1500 - - - ieee - 0 01005 trnet 101005 1500 - - - ibm - 0 0

  Remote SPAN VLANs------------------------------------------------------------------------------

  Primary Secondary Type Ports------- --------- ----------------- ------------------------------------------

  Hello

  first thing, please edit your post and remove your remote vty lines access password

  never send passwords on a public forum for the just in case production equipment

  line vty 0 4
  password xxxxxx

  ***********************

  Your question

  What is the configuration of the router as a switch which seems to work correctly you're saying and I configured its doing its job, don't forget you said that you cannot route no between the router and the router switch should take care of this, whats the vlan ports on the router are on is - what the same subnet do they get an ip address in the same subnet off dhcp as devices of switching, if they do, and you cannot ping them to the same subnet theres something upward on the side of the router it would treat for layer 3 routing ip traffic

  the ping to the router devices connected to the cisco switch and can the device on the router cannot ping devices switches

  If you move a device out of the router and attach it to the doe sit switch still work ok, reach the talk of the internet to other devices on the switch?

  As there is a layer 2 switch you don't need this command you have your entry door you can remove it.. .IP default-network 192.168.0.0

• ASA 5540 - cannot ping inside the interface

  Hi all. We have recently upgraded PIX to ASA5540 and we saw a strange thing going. In a Word, we can ping the inside interface of the ASA from any beach on our 6500 network (which is connected directly behind the ASA on the inside), but one where our monitoring tools are placed. Inside there is an ACL that allows all of our core networks, but it does not help that the interface is really strange.

  In the ASDM, I see messages like this:

  ID ICMP echo request: 2004 x.x.x.x y.y.y.y on the inside interface to. I don't think that's the problem, but I could be wrong.

  This is also the configuration of the interface VLAN VIRTUAL local area network from which we cannot ping inside the interface we can ping to and since this VLAN and machines without problem. The only problem is ping the inside interface of the ASA.

  interface Vlanx

  IP x.x.x.x 255.255.255.0

  IP broadcast directed to 199

  IP accounting output-packets

  IP pim sparse - dense mode

  route IP cache flow

  load-interval 30

  Has anyone experiences the problem like this before? Thanks in advance for any help.

  Can you post the output of the following on the ASA:-

  display the route

  And the output of your base layer diverter: -.

  show ip route<>

  HTH >