new modem has new network name

Similar Questions

• should make a new network if I replace my existing router

  I'm changing my router in an airport Time Capsule.  Should I make a new network name or can I just keep the existing one?

  If you have been changing since another router from Apple Airport Time Capsule, you'd be OK now the same wireless network name and password.

  You might be OK if you replace a third router to the airport Time Capsule, but the only way to truly know if you 'll be OK, is try it out.  Worst case, you go back and put in place a new name and a password and spend the next 30 minutes, connecting to a network of 'new' with all your wireless devices.

• Remove the old cable network name machine Vista

  I have 4 computers on a home network (2 portable wireless, Windows 7 and Vista) and 2 desktops (also Windows 7-Vista) to Windows 7 computers, replacing Vista computers in the near future.  Until them, I always use the four computers.

  I had a LOT of problems (unable to access printers and printers go offline) sharing printer and recently started having "Windows cannot access \\theWindows7newdesktopcomputer", those with printers attached - and I could / can not find a solution for this.  In desperation, I have reset the Linksys router e2500 manufactured back State initial and in the process gained a new network name (do not change).

  My problem is that the old Vista computer wired to the router insists on the use of the old network name (the one that appears on the screen of the network and sharing Center).  The funny thing is that I put on Jack autour with him (nothing has changed on the router) I have now access to the Internet on the old Vista computer wired to the router, even if she seems to be using the former name of network.  So, how can I get the Vista computer to recognize the new network name and quit using the former name of network.  I spent all day on this problem and I am not farther than I was when I started working on the problem of this morning on the printer share.  I guess that the router works because these two computers are connected to the router, but it doesn't look good for me and it seems that it must be something I can change or correct.

  Ron in round rock

  Try to remove from the network and sharing Center by clicking on the Home icon next to network name and go to mergere or delete network locations. I guess you know what to do after that.

  If it is used, then unplug your ethernet cable and try again.

• change the network name on my wireless router?

  A few months ago, I bought my linksys router and did the installation of all the stuff that day, including changing the name of the default network. I want to change the name to something different, but when I went to the address of the facility, there was no box to put the new network name [I was on standard wireless settings tab in the wireless section]. Help please?

  [Yay that worked, thank you:]

• 1217nfw MFP how to change network name and password when you buy a new routers

  I have a 1217nfw MFP.  It was working fine without thread.  Then my router has stopped working properly.  I bought a new router and easily set up my computer, the iPad and the iPhone to work with her.  But I don't know how to change the printer set up so that he will see and connect to the new router (i.e., change the network name and the password that the printer uses to connect).  Someone knows how to do this without having to uninstall and reinstall the printer as if it was fresh out of the box?  Thanks for your help.

  Thanks a lot for your help.  The choice to click on my laptop were not quite the same as stated in the article, but the article got to the right spot and I was able to figure out the rest.  So now my laptop is wireless printing.  MacBook Air my wife still does not work, but I'll play with it after the holiday weekend.  Do you know of an article that allows to change the name of the router and the password when it is a Mac?  Whatever it is, thank you very much for your quick response and help.

• Why the window asking if I want to make my new network domestic or public when I already a network set up. My original network now has a 2 square brackets also.

  I left my computer for my magic jack so I can receive calls.   When I woke in the morning, there were two open windows.   One was the new network

  window and the other was the window asking if I wanted to do a home network or public.   Does that mean someone hacked my computer?

  The fact that my network connection now has a (2) beside it means I have now two netowrk connections runinning.

  The system seems much slower and takes about 10 seconds to respond to the movements of the mouse if it has been sitting for awhile.

  Help, please

  Computer illiterate fool

  2 hooks would duplicate and feel safe to remove.

  If this is not the case, of course, run a spyware scan online TrendMicro Housecalls.

  http://housecall.trendmicro.com/

  I would contact Magic Jack support with this issue

  http://www.magicjacksupport.com/

• New router = the name of the new network, how can I get my wireless Dell 966 printer to recognize the new network?

  I got everything set up on my new network, but have not been able to set up my Dell 966 Wireless printer.  It worked fine with the old router.  The name of the network on the printer is still my old network name, not a new one.  I can't find the printer when I search for wireless.  Printer sharing is on, and the port is set for the printer.  I have reset the desktop computer and the printer.  I checked and double checked all connections.     9

  + The wireless set up the menu of the printer is the former name of network, and I don't know how to put the new name in.  It is grayed out so I can't select it.  I don't find a way to do it either from the office.  Any suggestions?

  Hello

  Configure the printer with a static IP address to connect directly to the router (read the manual).

  Next, configure the computers on the network to print to the static IP address.

  The network name or the name of the router would be important.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Unable to create the new network former TC

  Hello

  So I have the current generation of TC acting as a router as well as a HDD on my old to wide wireless broadband. I experienced some problems with connectivity recently (where my MacAir shows that I am connected to the internet, but no matter what site I try to access everything simply does not load and ends up with a progression of Ribbon on the address bar of Safari-turn off and turn on the power back constantly solves the problem), but this is not what I am asking today. Recently, I had the new optical fiber internet for my house and got a new modem and everything has been installed. Only one of the four ports in the modem seems to work, but at least it works. The D-link router that came with it works fine, but I want to use my TC as the router instead. However, whenever I connect the TC on the working port, I am unable to connect. Airport utility, the lights of TC in green but 'Internet' is yellow, i.e. does not work correctly. It should be a problem with the TC because the D-link router works on the same port and connection ethernet via a thunderbolt on the same port adapter works perfectly fine as well.

  Is this a problem with the old settings on my TC being incompatible with the new network? Please advise, thank you very much!

  There are at least 2 different issues at stake here and possibly 3.

  A question is that whenever you change the modem or the router that connects the TC, or your provider of Internet services, the TC must be reset back to settings by default, and then set it up again to work properly with the new product and the new service.

  You don't mention how old your 'old' Time Capsule can be, but 3 years is on the average life of the time Capsule, if anything more than 3 years will be suspicious where reliable operation.

  The third possible cause is that only a single port of your modem/router works when the four should work. If this is a real problem here, we can't say, but you have to wonder a little about the reliability of a product that doesn't seem to work properly

• P1102w - new router, the new network not printing

  I had the 1102w all set up and running on my network printing from 4 different computers. This morning, I changed a combination of westell/Belkin modem/router for a new modem router from verizon. I created a new network with wpa2 security. I got all the computers in place but the printer does not print - printer dialog reported an error in printing (no error message, just with the special printer, an error has been reported). The blue light continues to blink. I thought that it was because the printer was trying to talk with the new modem but did not have the wpa key. It also meant that I could not go in the printer from one of the computers to change the wireless settings. I tried to install it on my Surface via the USB port, but then I didn't know what to do. I tried the reboot and reset everything. I even disabled the security on the network then it would not require a password. But still, the blue LED flashes quickly and then turns off. The configuration page shows all 0.0.0.0 for different addresses even theough the computer is always looking on the IP that the printer used to keep.

  Help, please! How can I get the printer to reconnect to my network?

  Hello

  To connect the printer to your new wireless router, you must use the interface for installing software as follows:

  1. Download and run the latest version of the software below. escape in the installation, and then close the configuration screen that is launched:
     http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-80329-8&cc=us&DLC=en&LC=en&OS=4132&product=4110396&sw_lang=
  2. Navigate to C:\LJP1100_P1560_P1600_Full_Solution and run the HpSetup.exe file.
  3. Select easy install, then the Series HP Laserjet Professional P1100w.
  4. Select Configure to print over wireless network.
  5. Click next and follow the instructions on the screen.
     Note: the installation invites you to temporarily connect a USB cable to put the settings back wireless to the printer, be sure to unplug the unit once configuration is complete and the installation invites you to do so.

  Once configuration is complete, don't forget to restart the other PC and ensure that everything is running.

  Shlomi

• YOU UNLOCK THE IPHONE WHENEVER YOU JOIN A NEW NETWORK

  YOU UNLOCK THE IPHONE WHENEVER YOU JOIN A NEW NETWORK.

  Hi jonfromharrow,

  Thank you for contributing to the communities of Apple Support.

  You're asking about unlocking your iPhone then it can be used with other carriers (cellular)?

  If so, your original carrier has unlock the device before it can be used with other networks. How to unlock your iPhone for use with another carrier has detailed information about the process.

  If you need unlock the lock screen before joining wireless networks, try setting the password / settings Touch ID -use a password with your iPhone, iPad or iPod touch.

  All the best.

• Installed New Netgear Wireless Range extender but new network doesn't have internet access.

  I just installed a machine net universal range extender for WiFi and the signal over the Wan is very strong, but when I connect to him he says that have no internet access. What should I change? I post what I'm on the Ext network.but when I try to access other sites, it won't let me.

  I had the same problem as you and searched everywhere for a positive response and have not had a. I was about to return the netgear Extender when I, fortunately, has found a way around this strange problem.
  In fact, it's really simple, and I encourage really all those who eventually get this problem complain to netgear not having their detailed in the guide installation process that they shipped with the product.

  In my case, I have a WEP encrypted network.

  If you can't access the web interface of the Extender, you need to reset the device by inserting a paper clip in the small hole next to the WPS button (if you don't know already).

  When you are prompted for the encryption key and password for the network existing (the original one), you MUST WRITE THE PAST ON THE INPUT FIELD KEY word select and not the field the password. You can choose one of the 4 input key fields, but you MUST write the password on one of them and leave the field blank password (I think it's just for the WEP encryption, which is my case).

  I also changed the encryption type for the new network "_EXT" from WEP to WPA/TKIP but kept the same password.

  After the connection is complete the Extender successfully verified updates and all the IP addresses are assigned automatically via DHCP.

  I hope that I answered in the time before returning the Extender because I don't have a kind of complained after doing this.

  Good luck
  Marlon.

• I just got a new supplier of cable installed at home and now we find that our usual printer print wireless. How can I add this to the new network?

  I just had a new supplier of cable installed at home and now we recognize that our habit of printing wireless printer, how can I add this to the new network?

  Hello

  • What is the brand and model of the printer?
  • What happens when you try to print?
  • You receive an error message?

  You can view these methods:

  Method 1:

  Disable the firewall and check.

  The Windows Firewall is enabled by default in this version of Windows. To make sure that it has not been disabled, follow these steps:

  1. open the Windows Firewall by clicking the Start button, then Control Panel. In the search box, type firewall and then click onWindows Firewall.

  2. in the left pane, click turn Windows Firewall on or off. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. below for each type of network location, click on disable Windows Firewall, and then clickOK. We recommend that you turn on the firewall for all network location types.

  For more information, visit the following link:

  http://Windows.Microsoft.com/en-us/Windows7/Understanding-Windows-Firewall-settings

  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.

  Method 2:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  See also:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

• HP Officejet 6700 Premium: Unable to connect to the new network HP 6700

  I just changed networks and want to connect my HP Officejet 6700 Premium to the new network.

  In the control panel of the printer, I accessed network / Wireless Installation Wizard.  When I do, I get the message:

  Locking function

  This feature has been locked by your system administrator or the person who set up the printer.

  There is an OK button, but no other options.

  I get the same message when I tried to access a WiFi Protected Setup, and, for good measure, the default system restore.

  There is no administrator, in itself, because I'm the one who has set up the printer.  I'm rulnning a MacBook Pro on OS X El Capitan.

  Please, help me to know what I need to do to connect my printer to the network so I can print.

  Thank you very much for taking the time to answer and especially for providing additional resources should what was being offered as a solution to not work.

  I have tried your solution several times and kept getting the same message.  I tried shuttig the printer off by pulling on the power cord, stop in the right way, reverse iin, etc..  Nothing removed the error.

  Then I took the printer to a local Best Buy to show them the problem, which was at home.  We tried it a few times, and then, for no reason whatsoever (seems), it allowed us to do a reset.  No one knows what was different.

  My advice for anyone with the same problem is completely unplug it, let it sit for a while, keep trying and hope for the best.

• NET USE error: '67 system error has occurred. The network name cannot be found. »

  Original title: NET USE worked for error.

  OK I used the following with a RDP'ing of XP in a server of S2k3 years:

  NET use lpt2 \\SERVERNAME\printername /persiternt:yes

  now, I get a "system error 67has has occurred. The network name cannot be found. »

  What made me state was I restarted my XP machine.

  What I've done since then rebooted the box of the network, hubs, Wireless DSL modem router and the win 2 k 3 boxes with the same results...

  suggestions?

  Hey cvs334, would you unplug the ethernet cable from all these devices ' network box, hubs, Wireless DSL modem router and the win 2 k 3 boxes "then unplug the power cord for each. Then after about 60 seconds, connect waiting for DSL modem for sink power cord. Then plug the router after sink connect the router to the modem, and then connect the hub and other devices. This allows the automatic redirection Web DNS router to the modem. The router may be failing or the router LAN port may be faulty.

• Easy transfer - implementation of new user names

  I'm moving all my stuff to another computer using the seriously bad named 'easy' transfer - up to now very step has been atrocious.  I'm in what I thought was the last step - load data to an external hard disk in the destination computer.  On the destination computer discs had been authorized by my son, is "Virgin."   But at this last stage, I get to a command prompt in Easy Transfer which requires me to create new user names (or re - use previous) for both accounts that we already had.  But everything I put, including the old names, he says just 'mistake of creating user': the name of account, he will accept is former name of my son, and I cannot use this time.  But without giving users the two old names, he won't let me go.  There is absolutely no help available in Easy Transfer and therefore no idea whatever about what is actually wrong or how I can fix.  Help!

  Hi Colin,

  Thanks for posting your query in Microsoft Community.

  I understand from the information you have provided to us, you are facing problems with Easy Transfer in Windows Vista. I will certainly help you in this matter.

  Please check the link for the easy transfer settings.

  Transferring files and settings: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/transferring-files-and-settings-frequently-asked-questions

  Reference link:

  The problems of file transfer

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-transfer-problems

  If you face problems more when working with Windows Mail on the Microsoft Community Forum.