New thermal pads are needed?
Hi, I have a HP Pavilion DV4T-1400, with a bad card system.
I'm putting the new motherboard and I must of course reconnect the heat sync.
I have a thermal paste for the proc/heatsync but there are a few thermal pads on the Northbridge Clip that are always connected.
How is it important that I replace the thermal pads?
I replaced the thermal paste anyway.
Thanks for your help, I apologize for my n00bness.
It's hard to say. By the book, they should be replaced. But if they always seem good and you don't lose the thermal material then you can probably use again them.
You should never attempt to fill the gaps in the thermal paste, but it's up to you (I did previously on pads thermal office and never had a problem).
Just make sure that you use good quality thermal paste and apply it sparingly. You want just a thin layer between these surfaces.
Worst case scenario is that if you find your fan running higher than expected, you need to go back to the drawing board.
Hello, I have a question, is what heat pad should I use heat pads HP service guide for my graphics chip, this is what it says and how do I use them
"The thermal pads are used on the Northbridge contact (3) and chip Northbridge (4), chart/heat sink contact (5) and chip subsystem (6) graph and chart/heat sink contact (7) and capacitors (8).
The question is, what thermal pad use? Because I have a 0, 5mm thick, another of 1 mm and another 2 mm, and I don't know which one I need
Look at the picture on page 96 of the Manual:
Each chip that needs a thermal buffer is a different size and shape. Are the keys that you have replacements or you reuse the original? They are different sizes and shapes, apart from the thickness? Otherwise, I would bolt the heater without heat is dedicated to the as a dry and watch the free space on each chip. It should be obvious which cooling pads on the heat sink are closest chips on the motherboard and organize them accordingly. The pads should be compressed a little when screw you the radiator.
If it's 'the Answer' please click on 'Accept as Solution' to help others find it.
Dear SirMigrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD IDI am in a field & I'll migrate with a domain name.EX: now I'm in the field of the AAA tomorrow my domain name will change to BBB. User accounts are created in two AAA & BBB and the two domain user IDs are different.data servers are also migrating with the new domain.is it possible to access share with the old user id folder in new field or both to share the files again with the new user ID Active directory.Kind regardsChauvet J.
The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:
The result is a hp pavilion dv7 1245dx having heating issues so disassabled to clean it and apply new thermal grease and notice that the video chip has a thermal pad instead of thermal grease. This is what it looks like.
Guys/girls do you think it is reusable or do I need to replace it as well. If I need to replace it, what are my options? Difficult to find a pad thermal repalcement anywhere. A decent high CoolerMaster performace size heat for the CPU it's okay.
Yes, it uses a thermal buffer, because the gap is too big to fill with dough. You can reuse the pad. Some people even make a solid metal shim in sheet copper or a hammered out penny and you can apply heat is dedicated to that.
The fan on my laptop died so I am trying to replace the fan and the heatsink unit. The manual that I use specifies that thermal grease should be used on the cpu and heat pads must be used on the graphics processor and the capacitors.
The arrival of the new fan it came with heat pads on all relevant areas of the sink as a tube of thermal grease. When I removed the old fan, thermal pads have proved only on the capacitors and the components around the GPU and that thermal grease was used on the CPU and the GPU.
My question is: how this part must be installed? Should I remove the fron pads thermal heat sink that covers the processor cpu and graphics and do not use the thermal grease in these areas? Or the thermal grease can be used here and let the thermal pads on the heat sink?
Thanks for your help - thank you for the advice/opinions in this case.
You can remove the protections and pass with the dough so but only f, you are sure that the metal on the core processor and graphic is in solid contact. And there, I meant it touches and also has a lower compression. For me, the thermal paste is superior coolant and should be used on really hot spots. However, if the metal is not full, solid contact you run the risk of overheating.
If it's 'the Answer' please click on 'Accept as Solution' to help others find it.
new iphone 6s said needs to update itunes before restoring from itunes? How do update you a phone not yet active?
You need to update the version of iTunes on your computer, not the iPhone.
If you are using a Mac, use the App Store app to install iTunes updates available.
If you are using Windows, download the latest version of iTunes from the Apple website.
all programs are needed to start?
Apparently not.I have zero startup items and my system works fine. That may not work for everyone, but it's the way I like to run - lean and mean hoping for infections of malware if I can keep on my toes on the way to correctI don't know that anyone could tell you what startup programs, you need or those who you don't need without more information on the issue, trying to solve... or are - this just curiosity.Where do you see these startup items, that you remember to turn off and what are they?If you want to help looking at your startup items, I would like to start here:Since the Microsoft Answers forum does not have any kind of information system request when a new question is asked, we know absolutely nothing about your system. Not knowing the basic information a problem prolongs the frustration and the agony of these issues.Thank you MS Answers, allowing the resolution of simple problems as frustrating and a lot of time as possible.Provide information on your system, the better you can:What is your system brand and model?What is your Version of XP and the Service Pack?What is your Internet browser and version?Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..Next:I would like to use CCleaner to watch all your startup items and you might be able to identify and disable the (this may take a few passes) or if you look at the list of startup items and do not know what to do, you can publish a list of your startup items and someone can help you to look at.Here's how:Download CCleaner here:CCleaner allows you to manage most of the startup items and also do some other operations oriented cleaning. Some people will you recommend is not to use the registry functions in CCleaner to avoid these features for now. I have no problem with it for me, but sometimes it's a contentious issue, I prefer to avoid as much as possibleYou can uninstall CCleaner later if you don't like it.You can disable the startup items, see how things look and if you want to - delete totally useless, or just startup items leave the disabled while you continue troubleshooting. Note that disabling things does not uninstall anything, and if there is a problem, you can simply re-enable the point. If you're sure you don't want at all, then you can delete it.After launch of CCleaner and see what startup items you can disable/remove, if you are still not sure of your startup items, follow these steps:Run CCleaner and choose Tools, boot and bottom right, click on the button "Save to text file" to save the startup information in a text file on your desktop with a name you remember - something like startup.txtSave the boot information text file on your desktop (or somewhere you can find it) open the text file with an editor (Notepad or WordPad), select all (Ctrl-A), copy text, all the text selected in the Windows Clipboard (Ctrl-C) and then paste (Ctrl + V) the contents of the startup list to come back here in your next reply and maybe someone can tell you other things to consider.A more revealing startup Analyzer is Autoruns which will allow the manipulation of all sectors of boot and does not actually install anything:I have zero startup items on my computer and my startup list is empty, so none of this is important to me!
My latest lamp died with a JVM. I just replaced today and I want to retrieve my downloaded applications. After I restored the device of BlackBerry Desktop, any of my downloaded apps are there. I have a brand new 9860, together running 7.1. I run the App World. He told me to upgrade. When I followed the upgrades of the screen, I get an error message: notice: sorry your device does not meet the system requirements that are needed to support the BB App World. I have a brand new phone has so first question... I can update App World on Wi - FI. or should I do my first phone company data Plan? I've been running my old phone without data plan but enjoying use BBM and cell phone. Not happy.
Yes, hopefully soon... I know that the right people are aware of the "incorrect" error message
I just all new BB Curve 8900 on Vodafone. Its the first BB I've owned and I seem to have a bit of trouble. When I try to download the App World, I get the following error message:
"Device does not meet the system requirements that are needed to support Blackberry App World"
How can this be?
OK then... interesting for Vodafone to push support far... Well, by I guess.
So I guess that I change their instructions... rather than to remove an installed version of the AppWorld in the way they suggest, I suggest go to:
Homescreen > Options > Advanced Options > Applications
See if BB AppWorld is listed as installed. If so, highlight (but do not click) it and then press the BBKey and select Delete. If she wasn't there, then continue on these steps.
Then do a batt pull reboot:
With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes.
Then re - activate your THS:
Homescreen > Options > Advanced Options > host Routing Table > BBKey > sign up now
Then re - send all the service books:
Then do another reboot batt-pop.
Then, get a new link for AppWorld from here:
And re - download and install it.
I hope it's going to go right. If not, then it could still be useful a call to Vodafone...
See you soon!
I made the mistake of taking off the heat for the GPU and Chipset pads when I went to apply new thermal paste to the CPU. The thermal paste on the CPU is fine but not, I get artifacts and heat ups when I play games because of the keys. I reapplied the pads but I'm afraid I've damaged one of the keys.
Is there anywhere I can get the original for the gpu and chipset pads? Also they felt a bit greasy when I removed, HP use the thermal grease on top a thermal buffer? If Yes this is weird lol.
If I can't get the originals anyone has a recommendation indicating where I can get a few buffers that will do anything as well?
Although it was a solution, however is not a good thing. After dealing with heat from take the pads off I decided to buy another radiator with the pads on them.
Now, everything is very fine and back to normal. I suggest to everyone to never take these. They seem to be of good quality for a thermal buffer and dissipate heat much better than the thermal paste.
Hi I have a M17x which came with two Nvidia Geforce GTX 280 m SLI graphics cards, as I can switch between hybrid and discrete graphics modes I believe is the saying,
It also has the third on board graphic chip Nvidia Geforce 9400, which is where my question in fact because this chip shares the same radiator as well cpu I upgraded the processor is a few days and doing so re thermaled the cpu but the Geforce 9400 looked like originally, he was given a bottle and not glued?
So I left as is and re - apply the heatsink on the cpu and 9400 each chip has 4 screws around the cpu & gpu lock and hope for the best.
But since I kept an eye on the time and the Nvidia Geforce 9400 that i never, I always use SLI with the 280 has seen some time whereas this is not used and every other chip is always at least 20 degrees colder I saw between 60 81 deg while everything else is way lower so that I have to buy thermal pads and use a sub it or can I use the same dough I used on my cpu because it must be the problem, Yes?
We recommend that you use a heat mat or use the same dough, either option should help to lower temperatures. Temperatures are high for this type of video card, especially if you don't use it yet.
Hello. I just know that the muse and I need an organization of customers in alphabetical order. The problem is that you will always get new clients. I need to know how to insert a new customer (square), and it is already in alphabetical order on the page.
I just know that the muse and I need guests alphabetical organization. The problem is that you will always get new clients. I need to know how to insert a new customer (square), and it is already in alphabetical order on the page. The site will be as in the link below, and each customer will have a window of these: http://www.connary.com/. I look back.
A hug, Murilo.
I believe you are referring to the rectangles of tile as visitors on the page? not exactly customer database?
You can add rectangle with different effects with rollover State of mouse and about adding new, you must do this manually in design mode.
I need to move my copy of my old computer to a new CS6. I need my license reset?
You are allowed to have the software installed and enabled on both machines, so there is nothing you need to install other than (and not move) the software on the new machine, unless you already have it enabled on both machines.
If you do not plan to use the old machine again or prefer to simply remove the software, or you want to keep an activation of another machine at any given time, it is preferable that you clear beforehand. To disable an opening of applications and choose Help-> Deactivate. Once disable you there is nothing else you need to do unless you want to uninstall as well to gain more disk space.
Hello. I'll be repair (and cleaning after 6 years) 2009 end iMac coz ' the screen has five 2cm thick, uniformly distributed, striped of vertical lines (it is still usable in Mode safe), which indicates a good chip GPU (used to pass all the tests of stress for the GPU and GPU memory) but a subcomponent that surrounds it has weld fracture joint coz' it may have overheated in the summer (which has a record high 36 to 42 degrees Celsius) and OS X might not revved up fans enough that may have contributed to cause solder joint breaking.
When I open the iMac Monday, the thermal pads for memories of the GPU (surrounds the GPU chip I use a thermal paste with) may not be in good condition more. I was wondering how thick cushion is suitable for the GPU of the iMac (an ATI Radeon HD 4850 512 MB), what brand and what type (if the thickness is perhaps the most important)?
Thank you. God bless you. Revelation 21:4
I would like to contact https://www.ifixit.com/
If anyone should know...
What files are needed to access the aspect of the heritage of GarageBand? After the upgrade my MacBook Pro and Mac Pro, the appearance of the inheritance is only accessible to the general public on the MacBook Pro. What files are needed for these instruments of the legacy and the filters on my MacPro? I read that the removal and reinstallation of GarageBand 6.05 will do but 6.05 GB certificates have expired and is no longer allow it to be installed. Any help is greatly appreciated.
I read that the removal and reinstallation of GarageBand 6.05 will do but 6.05 GB certificates have expired and is no longer allow it to be installed. Any help is greatly appreciated.
You always have an installer for GarageBand 11? An installation of iLife 11 DVD or the DVD Installer original system for snowLeopard with applications for funding?
You can install GarageBand 11 of these media, if you set the date system your mac to a date until the installer has been released. Then, the certificate will be valid.
the appearance of the inheritance is only accessible to the general public on the MacBook Pro.
But because of legacy patches are available on your MacBook pro, you can copy all the missing files from the library of the Instrument and loop library in your other Mac.
Compare these files in the folder/library on your system drive on Mac of high level.
The instrument library: Library/Library/Application Support/GarageBand/Instrument.
and loop library: / Library/Audio/Apple Loops/Apple /.
Copy all the files to the corresponding folders on your MacBook Pro that is not there.
Maybe you are looking for
I have an iPhone 6. I have upgraded to iOS 10 (10.0.1) this morning. Everything seems to work very well with the exception of Siri is unable to send text messages. It was working fine before the upgrade. 'Hey Siri' addresses. I say to "send a mes
everytime I open the application App Store it tells me that there is an available update (9.6.1) for iPhoto and then it tells me that I can not update it for reasons that do not apply to me as if it was the bad apple id I have iPhoto 9.4.3. Is it imp
Hello My TV card does not work with Vista32 SP1. Material contol said all workers, but the Media Center Receiver service crashes immediately after departure. Did someone knows a solution? Your Ruediger
Hi all It all started a month ago or not.My keyboard of laptop (a Toshiba Satellite P850-12Z) began to fail. First was the BACKSPACE key, but subsequently was the numeric keypad 3 key and the Enter key. They start working if I hit them several times
I get the error message "Windows was unable to find a certificate to log the edandjane network. What is the certificate that I need and how to reset my computer so I can get on the network with my laptop. The new router is an edandjane SSID NetgearN6