new WRT54G2 access point see an Internet cable modem connection

Similar Questions

• My WRT54g2 can not see the internet through my wrt54g...

  My company gave me a new laptop which allow no connectivity WEP. I need wep for printers and other devices on my network so I bought a new wrt54g2 to manage wireless WPA and plugged into one of the ports opened on the old router. I went to the admin and everything set up for my taste, but for some reason any that it won't catch a connection... What should I do so that he could see the internet through the old router...

  If you connect a router to another, connect the two together by network ports. Then turn off the DHCP server on the router of the second, which sounds like the WRT54G2 in this case. You may also have to reconfigure the second router local IP address out in the same IP range as the first router but outside the DHCP server on the router from the first milking. For example, if the local IP address of router then the router is on 192.168.1.1, two IP local to 192.168.1. 5 (or something of the sort).

  Or autour routers and use the WRT54G2 as the main and several router that is configured for the secondary router WEP and turn DHCP on the secondary router. Other changes such as the reconfiguration of the local IP address of the second router must always be made. Or check your existing wireless devices configured for WEP see if they will support or can be updated for decision-making support WPA or WPA2. If so remove the existing router and use the WRT54G2 in its place.

  Also, make sure that both routers have different names for SSID wireless and are on different wireless channels to avoid a conflict.

• D6200 Access Point - 2.4 is no longer connects 99% of the time

  Hi gurus, I have a D6200 which is defined as an Access Point (I have to use my ISP modem issued their secret squirrel nature do not share the parameters and limitations of VOIP, but that's another story). I had already used the D6200 before getting the NBN (Australia) and so why was happy to keep the same configuration of network with her now implemented as an AP.

  In any case, served as AP all 2.4 and 5 without problems with things like my printer and Panel Solar Inverter only able to use the network 2.4. Like today I can connect is 2.4 (warned, saying: I have the wrong password)-had a power outage yesterday that could have an impact, but seems odd when only 2.4 network hit.

  -J' have confirmed the password, delete all.

  -Checked the channels for interference, all clear (tried a few others just in case where)

  -Tried a simple power cycle, no joy.

  -J' have done a factory reset, reconfigured AP, created with pre-existing, passwords and network names. 5 works fine, 2.4, no joy.

  -An another factory reset and reconfigure but leaving name network and passwords according to the default. 5 works fine. 2.4... worked well on my iphone6, but not on my ipad (always get incorrect password). Unable to connect via 2.4 via macbook either.

  -Just not changed my phone from 2.4 to 5 no worries, attempted to return to the 2.4 password and wants new and can no longer access

  I am at a loss. I have seen many problems with 2.4 in the forums, but nothing that seems to relate directly to it (which has not been fixed with a simple factory reset).

  See you soon. Diving.

  Ok. I can't explain it, but then nothing for a few days, connected to the computer today and was able to conenct to 2.4 did the same with the phone and the printer and everything back to normal. So I guess that the solution to this problem is to do nothing for a few days and hope for the best. I can't contact at all but I'm glad I'm not buying a new router in the meantime.

• Do I need to have the conexant modem when I already have internet cable modem. I continue to receive messages from windows that I need to install a driver

  I bought this computer used for the school. previously, the owner used AOL and dial-up. I have cable and a cable modem, so I removed the modem to see State of windows that they needed to install a driver for the computer to work. Also, I have windows 7 on my old computer, but have not been able to install it.

  Hi Crystal, azure

  If you are using a router/cable modem, then you don't need to dial the modem conexant. If you are asked for the driver, then you can either install the driver or, if you want to get rid of the quite conextant modem you can remove the material completely, assuming you know how to do this. Of course, you will have to open your case and remove the conextant modem. For this I guess you have a desktop PC. A laptop would be more difficult to remove the conexant modem, unless the modem is a stand alone.

  You give no details as to your problem of not being able to install Windows 7. More information will be required before anyone can really help you with this problem. An idea of what is happenning when you try to install windows 7 and error messages would be useful; What version of Windows 7 and whether retail or OEM. By the way if you try to install an OEM copy from another PC on your computer then you will obviously have problems like the copy so attached to the first PC OEM installed on the byt the PC manufacturer.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com

• New wireless card will see available networks but not connect

  For over year I now, I had been using a USB wireless network (I'm not sure it's official name) fine to connect my desktop computer to the wireless, but when that broken I decided to use a wireless card instead. I plugged it to the PC installed the drivers that came on the disc and restarted my PC, when he started upward I saw my (and a few of my neighbors) points of access wireless, but when I tried to connect it gave me varies from error messages including the single "windows was unable to connect to . as well as to tell me the password was wrong a few times (this however is not the case) and finally he would be in touch with ' limited access. When I now run the possibility of troubleshooting problems, it tells me I have a "problem with the wireless adapter or access point" which has not been set. But before he also gave erros as an asisgned not correctly IP address"(I don't remember the exact wording).
  During and since these errors I have restarted my computer several times, reinstalled the drivers from scratch several times and as he told me I had a problem with UP-address I ran have run the command "ipconfig/all", which produces the following section under 'WiFi 2' (who is the connection I am trying to connect):
  The connection-specific DNS suffix:
  Description: 802.11n Wireless LAN Card
  Physical address: C8-3A-35-C9-FF-1C
  DHCP enabled: Yes
  Autoconfiguration enabled: Yes
  Link-local IPv6 address: fe90::2427:959c:823 b: cde8% 30 (Preferred)
  Autoconfiguration IPv4 address: 169.254.205.232 (Preferred)
  Subnet mask: 255.255.0.0
  Default gateway:
  DHCPv6 IOOKING: 516438581
  DHCPv6 DUID client: 00-01-00-01-17-7D-CD-F1-BC-AEC-5-26-31-DE
  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP: enabled
  The card that I use is the Tenda W311P and my install of windows is windows 7 Ultimate, the hub I'm trying to connect to is a Hub of BThome.

  Thanks for your time.

  Tom

  Hi Thomas,

  Thanks for posting your query in Microsoft Community.

  I understand that you are facing problems with wireless network in Windows 7.

  I imagine the inconvenience that you are experiencing. I will certainly help you in this matter.

  Were there any changes made to the computer before the show?

  Please follow the steps in the link.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-in/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope it will be useful. If you still have questions, please reply and we will be happy to help you.

• WAG320N and cable modem connection

  I have a small question,

  You could point me to some reference material on my WAG320N configuration to use my modem cable via Ethernet 1 port. I saw that he mentioned it's possible, but I have been unable to me sorting.

  And before ask you, I put the DSL router that I move in the next 12 months and my new base will not have access to cable internet and I'll be going back to DSL.

  Thanks in advance,

  Phil

  Actually in this case your bad, but thank you for the quick response.

  After a few game, it seems that the WAG320N is specifically configured to configure Ethernet Port 1 WAN port and you can route all internet traffic through the modem cable via the WAN port, you just set up.

  If anyone is interested, then load up your routers page 192.168.1.1 default config.

  Click Setup

  - Ethernet

  Next to Ethernet connection: select the button labeled radio like Port WAN

  Most of the stand-alone cable modems will have a static IP address both under the list of connection

                           down box  Select the static IP address.

  Enter the IP address of your cable modem, subnet mask, gateway and DNS address by default. (These items must have all be supplied by your ISP)

  And finally click on Save settings at the bottom of the screen to validate your changes.

  Then connect to your WAG via the Ethernet switch or wireless connection and you should be good for surfing the web.

  I hope this helps someone else who tries to use a modem cable through the WAG320N or similar device.

• Lose the wireless connection when the modem connects to the internet.

  Hello

  I've updated my laptop to windows 7 (new installation).  I have a cable modem which is connected by ethernet to a wireless modem/router which I have configured to be a wireless access point (dhcp is the cable modem).  The laptop can connect wireless access point when the cable modem is not connected to the internet (so the ip address of the access point is 192.168.100.50 & the laptop takes an automatic ip address within the range). The problem is when I connect the modem cable to the internet, & so the ip address of the access point is derived the cable modem, the laptop can't connect to the access point. When I renew the ip address of the wireless card, it says it is connected to the selected network but the ip address is not correct, nor do I have access to the internet.

  The laptop connects fine to pick up the new ip address when it is ethernet connected the access point when the cable modem is both on or off, so I can access the local access point configuration when the modem cable is off, & can access the internet when the cable modem is enabled. When it is connected with the cable modem access point wireless at sea, both my wireless & ethernet connection say that they are connected to the selected network, but as soon as I turn on the cable modem, wireless connection says it is connected to an unidentified network, but my ethernet connection is connected to the selected network.

  I tried the broadcasting/no broadcast of the SSID, different levels of security, modification of the power saving options on the card wireless without success. I don't think it's a problem with the real network that the wireless card can capture the network & settings when the cable modem is disabled.

  This Setup has worked well when I had win xp.  My mobile phone can capture the network without wire end also & is able to access the internet.  The driver for the wireless card is current as well as the firmware on the access point.

  Can you please help? Thank you very much

  Hi Jack

  You led me in the right direction with the MAC addresses on the cable modem.  It's a simple solution... turn off the cable modem so it would refresh the MAC addresses of connecting devices, & hey presto, I wireless & ethernet access internet on my laptop with wireless internet on my laptop.

  Thank you for your perseverance.

  See you soon

• Connection of comments on the second WNR1000v3 as access point does not connect to Internet

  I have a WNR1000v3 (firmware V1.0.2.68_60.0.93NA) connected to the WAN and it works well. His IP address is 192.168.0.1, subnet 255.255.255.0, gateway 192.168.0.1, mask and DNS servers are on 8.8.8.8/8.8.4.4. DHCP is configured to 192.168.0.10 to 192.168.0.100. I have a guest connection configured and it works well.

  I have a * second * WNR1000v3 (same firmware) bound to the first as access by using these instructions: http://kb.netgear.com/app/answers/detail/a_id/23784/~/how-to-automatically-configure-a-netgear-route...

  I gave him the IP 192.168.0.2, subnet mask 255.255.255.0, gateway 192.168.0.1, and DNS servers again the value of Google. It has the same SSID wireless as the main router and I can move seamlessly between the two. The devices connected to the LAN ports on this access point work very well. Wireless connection works fine.

  I then configured the connection even guest on the second router (the one running in access point mode) and I can get an IP address when I use it. However I can't access the Internet. Ping 192.168.0.1, 192.168.0.2, and 173.194.33.137 (the IP local google.com) all fail.

  Guest connection is not supported on a router functioning as an access point? Or am I missing something really obvious?

  Thank you

  Bill

  @storm1985 I suspect that your configuration means that all the second router LAN ports will also forward only to the Internet. But this gives me a good idea to use another router just like an access point wireless for the connection of comments. (I seem to accumulate old routers.) Unfortunately, I don't have the time to try this out until late in the week, but I'll certainly do and report. Thank you!

• Should switch BEFSR81 - wireless access point I use?

  Hello

  I have a cable modem connected to a Linksys BEFSR81 switch under the stairs. It distributes points of LAN cable to every room of the House - it worked perfectly for years and continues to do so.

  I need to add wireless (for iPhones etc.). I connected a Netgear WPNT834 DSL wireless router in a LAN points. It broadcasts a SSID I can 'see' on my iPhone - I can connect to it, but cannot access the Internet.

  Looking good, I found the two devices by default the IP 192.168.1.1, so I changed the IP address on the BEFSR81 on 192.168.1.2. Still no access to the Internet via the wireless Netgear.

  I guess that there is a relationship between the two devices share the bandwidth, but I'm at a loss to know where to start.

  These two devices are not compatible, or is there a way to their cascade work together? Or, is it a point of access wireless (linksys or cheaper universal device) that I can plug into one of the LAN edge to add a wireless network to the existing local network?

  Thanks for your help.

  Hi Mikey'it,

  The Netgear and Linksys are compatible when you want to set up this way. You must configure the Netgear router to a wireless switch. As disable the "router" function and DHCP. You must ask the Netgear support how to do it. Because the Linksys router works perfectly, you need to change anything.

  

• setting up wrt150N as access point

  Hello.. Please bare with me.
  In my previous House, I had my cable modem connected to a dlink wireless router. I used a port on the dlink lan and connected to my wrt150n that is configured as an access point. It has worked flawlessly. I was able to create a network and share files between computers regardless of what router they were physically connected to.

  Fast forward a year and in my new House, I have a dlink WIRED router connected to my modem (different ISP) and to a lan port on the router im connected to the port of the wrt150n 'internet '. The computer is connected to the 150n can access the internet and the portion wireless works fine, but it does not connect to another computer that is connected directly to the router wired dlink.

  From the computer connected to the linksys, I can;

  router dlink ping

  router linksys ping

  ping ip address ONLY, the second computer that is connected to the dlink router

  The computer connected to the dlink, I can;

  router dlink ping

  I can not ping ip address AND name of the other computer

  I cannot ping the router linksys

  Is happening here?

  What setting should I watch these two computers to be on the same home network?

  Dlink ip address is 192.168.0.1

  Address IP Linksys is 192.168.1.1

  He was installing it in my old House and worked well.

  Unfortunately, my warranty is up and linksys don't offer me a tech support.

  any help would be GREATLY appreciated, I really need my home network courses.

  It's just the way you have implemented: you configured the WRT as router and so you have created two separate LAN segments and areas of broadcasting. Emissions of LAN will not cross a router. Name resolution for the WIndows work group works on the basis of emissions, either it works on the same segment of LAN never beyond a router. For example, if you want to keep this type of installation, you will need to use the IP address to connect to computers on the Dlink from computers on the WRT. Reverse is not possible at all because the WRT does NAT which makes LAN inaccessible on the internet port.

  You want only the WRT as access point and you seem to want connectivity complete between all your computers I would say that you reconfigure the WRT.

  1. disconnect the WRT from D-Link.

  2. connect a computer to the WRT. Open the web interface at http://192.168.1.1/

  3. on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.0.2 and disable the DHCP server.

  4. save the settings. You will lose the connection.

  5. unplug the computer and wire to one of the LAN ports of the WRT to your D-Link router.

  That's all. Now all your computers to connect to the same local network and are in the same broadcast domain. All computers use IP addresses * 192.168.0 and have internet through D-Link.

  Make sure that the DHCP server on the D-Link will not affect 192.168.0.2 to another computer or device on your network. This would cause a conflict of IP address.

• Configure the WRT610N as an access point?

  I have a local wired network with a WAP54G access point that connects the 2 laptops wireless for the local network and internet.  I want to replace the access point with a WRT610N.   How to configure the WRT610N as an access point?   Can I connect my access point to the Internet on the WRT610N, or to one of the four ethernet ports cable Cat6?

  Thanks for the help.

  
  

• Intel WiFi Link 1000 bgn @ E220s: visible, but will not connect to access point

  Hello

  just got my new E220s - love it! Only problem is that I can see the wireless access points, but whenever I try to connect to them it says: "Windows could not connect to '.»»

  My setup is a Lenovo TinkPad E220s: Intel Core i5, Intel WiFi Link 1000 bgn, Bluetooth 3.0, 7200 RPM 320 GB HDD, 4 GB RAM, Windows7 Home Premium.

  My system is up to date with regard to the update of Windows and Lenovo BIOS update.

  * A tried to connect to a FritzBox 7141 (b, g, g ++ standards)

  * with WPA - PSK: entered the password-> problem as above

  encryption-> problem as above

  * Connection I tried with 'eduroam' (wifi popular education in the world)-> problem as above

  * Using the driver Lenovo 14.0.1-> problem as above

  * Manually install driver Intel 14.1.1.3-> problem as above

  'Manual Diagnostic tool' Intel:

  * test hardware: past

  * pilot: past

  * radio test: past

  * scan test: past

  * association test: failed

  * other tests: does not work

  Some diagnoses more Windows:

  Details about network adapter diagnosis: Network adapter Wireless Network Connection driver information: Description . . . . . . . . . . : Intel(R) WiFi Link 1000 BGN Manufacturer . . . . . . . . . : Intel Corporation Provider . . . . . . . . . . . : Intel Version . . . . . . . . . . . : 14.0.0.113 Inf File Name . . . . . . . . . : C:\Windows\INF\oem14.inf Inf File Date . . . . . . . . . : Tuesday, November 09, 2010 8:43:32 AM Section Name . . . . . . . . . : Install_MPCIEX_Lenovo_1000_HMC_BGN_WIN7_64 Hardware ID . . . . . . . . . . : pci\ven_8086&dev_0084&subsys_13158086 Instance Status Flags . . . . . : 0x180200a Device Manager Status Code . . : 0 IfType . . . . . . . . . . . . : 71 Physical Media Type . . . . . . : 9

  Hello

  Problem solved. Of wire antennas was not of all attached to the card and the other it has established relationships by chance. It took me 3/4 of an hour to turn off the battery, remove the keyboard, attach wires to the NIC (quite difficult due to lack of space) and put it all together. Then everything worked fine.

  Thanks for the help, forum!

  E220s rocks!

• Use E2000 as ONLY - wireless access point not as a router

  I would use my E2000 router as an only Wi - Fi access point. The unit will be connected to a unit of combo modem/router Verizon FiOS Actiontek I want to leave only the first and only router on my network. Can the E2000 cause its router functions disabled without DD - WRT or other third party firmware?

  Thank you!

  Yes, but you need to connect a cable between the router to the AP, here's how

  Editing cascading (connecting) a Linksys router to another router

• Configure a wrt320n and wrt150n as a wireless bridge or access point

  Hello

  I have a question: I would like to connect my old wrt150n as an access point on a different floor of our House because of a bad signal to the second floor of the wrt320n.

  Is a cable modem connected to the wrt320n. I would like to connect wrt150n wireless to the wrt320n, so children can connect to their computer for the wrt150n wireless...

  Is it possible to configure?

  THX in advanced, Peter

  No, it is not possible... Router Linksys will not communicate wirelessly with another router.

• configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

  HI people,

  I am brand new to Cisco Wireless, just that I bought new wireless access point air-ap1142n-a-k9 cisco, try to configure the configuration of wpa2 for security reason, but impossible to configure in any mode security. So my AP is currently no security / encryption mode.

  Could someone can help and suggest me I will appreciate if I get all documents, so the security problem can be solved.

  Concerning

  Sanjeev

  OK great

  ----------------------------------------------------------------------------------------------------------------------

  Be sure to note the correct answer and mark the thread as answered