NI 9148 with LabView module detection

Hello

I got the task of creating a deployable (compiled) software to a DAQ system with NI 9148 Ethernet RIO basket background and various modules. The user must have the ability to change the module type and the location of the different tests, so the application must detect (or the user specify) what modules are at what positions.

I watched the blockset CRY, however this chassis is not supported and the lowest level blocks are protected. Is it possible to read the serial number of the modules connected to the 9148 OR position, type, and if all goes well?

Thanks for any help!

Hello Soonxaf,

What are you helps as a controller-is this RT or Windows? Are you planning on the use of analysis of RIO or LabVIEW FPGA engine?

If you plan use the analytical engine, so this should help you get started:

Tutorial: Discovery, Configuration and programming access of the CompactRIO Scan Mode to IO with LabVIEW

http://www.NI.com/white-paper/9351/en

Kind regards

Tags: NI Software

Similar Questions

  • Hi, can someone give me some ideas on what type/brand of usb cameras are not suitable for labview? I need to use with labview and IMAQ Cheers acquisition image vision module

    Hi, can someone give me some ideas on what type/brand of usb cameras are not suitable for labview? I need to use with labview and image acquisition IMAQCheers vision module

    Hi, I use a 1.4MP USB camera with LabView. The brand is ID - a German company.

  • HELP - FPGA SPARTAN 3E-100 CP132 WORKS WITH LABVIEW FPGA?

    HI EVERYONE, GET ON IM TRYING TO USE MY FPGA WITH LABVIEW, BUT I DO KNOW THAT IF ITS COMPATIBLE, I INSTALLED THE DRIVERS, MODULE FPGA AND LABVIEW 2012, IM USING WINDOWS 7 32 BIT, AND AFTER I COMPILED ITS SAYS:

    LabVIEW FPGA called another software component, and the component returned the following error:

    Error code:-310601

    NOR-COBS: Impossible to detect the communication cable.
    Check the communication cable is plugged into your computer and your target. Also, verify that the proper drivers are installed.

    Thank you.

    =)

    Hi dvaldez2.

    LabVIEW FPGA offers no support for any material to third parties, other than the 3rd Spartan XUP Starter Kit. These are probably the drivers you downloaded.

    http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

    However, this driver supports only the Starter Kit Board itself (http://www.digilentinc.com/Products/Detail.cfm?NavPath=2, 400, 790 & Prod = S3EBOARD). You may not use the driver with any other Xilinx FPGAS.

    I hope this helps.

  • Configure the cDAQ by programming with LabVIEW

    I have a chassis cDAQ with two modules. I want to (for reasons peculiar, too complicated to enter in ) to be wheat to programmatically configure the MAX configuration for it. And I mean everything.

    I need, in my LabVIEW application, to be able to tell MAX to wipe its current configuration, detect the chassis with the two modules, rename the chassis and two modules and create a lot of tasks.

    I'm pretty sure I can create jobs by program, but I had little luck find info on reconfiguring hardware detected programmatically.

    Can it be done?

    Thoric,

    The only way I know to rename the material without using MAX is to import a configuration file with new names for the same hardware.  One version of the configuration file is a. INI file which as you know is very easy to create/edit in LV MAX copy Configuration.vi can move the configuration file in both directions.  I've been playing with it using my cDAQ and it seems to work.

    I could see getting started material and leave the OR to detect it.

    Config for export. INI and change the names of items, etc.

    Import configuration updated the Max and replace the existing configuration

    Here's a quick example of how I did the export/import

  • Analog value read with DSC Module Modbus

    Hi, I have a Delta PLC with an AD converter module. I use the four analog channels and in one of them, I have a thermocouple which displays temperature data on a microprocessor thermocouple meter. However, I want to display the data in Labview. The controller communicates with labview through the DSC Module of labview with success, but I am not able to read the data. Looking forward to your help.

    Found the solution. addressing to the modbus master was different for this model of plc, so I looked up the address for delta plc Modbus and the analog read list has been a success on labview.

  • temperature measurement with labview on four location using NTC thermistor


    Hello
    My project is the measure of the temperature of a thermistor on-site 4 difference.
    The measures must be 0 for 100 * C.

    details.

    • For the sensor, I must use only NTC thermistor.
    • I have to do an application with Labview.
    • the application must give me the right measure in real time, and it should save the sample in a database.
    • This measure is taken max 20 feet form the pc.

    I'm new with this.
    Can someone help me with sensor circuits.
    How can use DAQ with the thermistor.
    Can I use EMANT300 Low-Cost USB DAQ Module 24 bit?

    Please give an idea

  • Not compatible with Labview 2014 IMAQ?

    I try to work with a National Instruments / SuperDroid Robots SD6 ( https://decibel.ni.com/content/docs/DOC-18528 ) now... Everyting connects fine using LabVIEW 2014 with the module of Robotics with the exception of the functionality of the camera. When you use the solutions provided LabVIEW cannot find dependencies IMAQ.

    I checked to make sure that I have the module installed and I see IMAQ 4.9 and IMAQdx 4.3.5 MAX

    Check the newsletter below on the compatibility of the IMAQ, she only has not 2014 listed

    http://digital.NI.com/public.nsf/allkb/DB928F6D5E9D6B97862579A7006B2850

    Specifically, I need the 2014 Image processing module version in the link below. The download link says 2013 and during the installation process, I don't see an option for support for 2014.

    http://www.NI.com/gate/GB/GB_EVALTLKTSIGPROC/us

    Is there a trial version of this software that is compatible with LabVIEW 2014?

    I was able to get in touch with a sales engineer and I need to image processing module is not yet available for LabVIEW 2014. Where my question.

  • How to find the point of leakage with Labview?

    I use a myRIO to develop a system to help people imapaired in their navigation to visually. I already have the image processing of which is to be acquired by the device (edge detection and research of straight lines).

    How can I end the vanishing point of the two edges of a path to an image with LabVIEW? There is a special function that I can use?

    Thank you!

    The vanishing point is the intersection of two lines, no?

    https://www.Google.com/webhp?SourceID=chrome-instant&ion=1&ESPV=2&IE=UTF-8#q=intersect%20point%20Of%...

  • NEITHER 9512 with Labview FPGA Interface

    Is it possible to use the NI 9512 stepper with Labview FPGA interface drive unit or is it only possible to use it with the interface of scanning? When I try to add the module to a FPGA target, I get an error telling me that Labview FPGA does not support this module with the latest version of NOR-RIO, but I have the latest version of OR-installed RIO.

    Hi Checkit,

    You're right - the 9512 cannot currently be used in FPGA. There is an error in the documentation. The 9514 and 9516 can, however.

  • smartphone with labview programming

    is it possible to run programs that I've written in labview on a smartphone? (iphone/android/new windows 8?)

    is it possible to program a smartphone with labview?

    Your questions were asked before several times. Please search before asking a question to see if it has already been covered or partially answered.

    With regard to your questions:

    NO.

    and

    Laughing out loud

    The LabVIEW Embedded Module has been designed to work with Windows Mobile, but not Windows phone (what Mobile has been transformed in). Several ideas exist in the exchange of ideas of LabVIEW in this regard. OR (supposedly) works on them, but have not announced anything. In the meantime you can try to use something like this:https://decibel.ni.com/content/docs/DOC-19387 or this: http://sine.ni.com/nips/cds/view/p/lang/en/nid/210042

  • Is DAQ Measurement Computing USB - 1608FS compatible with labview?

    I have DAQ USB-1608FS from Measurement Computing company, and I was trying to see if it is possible to use

    This data acquisition with labview 2012. I tried to download the drivers from their company http://www.mccdaq.com/usb-data-acquisition/USB-1608FS.aspx

    but when I tried to use labview in the DAQmx the DAQ tool is not detect it by LabView. So, if anybody out there knows if this data acquisition

    really can work with labview, please let me know.

    Their driver seems to be ULx http://www.mccdaq.com/daq-software/universal-library-extensions-lv.aspx

    and he said that he supports LabVIEW 2012. I suppose you open a sample and the device does not appear? The device is displayed in the Windows Device Manager? It seems that this driver/device will work, there may be just a few questions it initialize properly on your machine (either with Windows or Measurement Computing software). You must be to open a debate on their forums or call their support help line.

    Good luck! Let us know some of the above and, of course, let us know if find you the solution.

    -gavin

  • Trouble with USB-6501 with Labview 8.6 Pro for Mac OS

    Hello

    I have a unit USB-6501 I try to use with Labview 8.6 for Mac Pro to processor intel.

    I have the driver NOR-DAQmx base 3.2 for Mac installed and when I ran "Isdaq", it detects the device and also warned that the firmware needs to be updated. So, I ran the "FWUpdate" for updating the firmware. I double check the Isdaq and it detects the device as "NI USB-6501:"Dev1"(USB0::0x3923:0x718A:014386 B 0: RAW).

    Now, when I run Labview 8.6 and DAQmx Base create channel VI and the port of 'physical' wire to the control, nothing appears in the available device.

    Also, when I run the mxbaseconfig program, not the existing basic tasks detect the device.

    Could someone please help me get this to work? Basically, I need to read and write slow digital data through USB-6501. But, the Labview does not detect the device.

    Thank you

    Keong,

    I do not know what causes this, but place a task create VI before your code and the wire of the output task to the task of entering the chain and try to run that.  Please let me know if it works for you.

  • Cannot bind to the shared object created with LabVIEW 2009

    I have problems referring to a shared library built from a LabVIEW VI under RHEL 5 with LabVIEW 2009.

    To illustrate the problem, I created a VI with a digital input and output that corresponds to a certain number. Then, I created a draft specification of build to create a shared library with a feature that makes use of this VI square. The shared object is created successfully (square.so).

    When I try to compile a test application written in C, that connects to this library, I get errors in the following link:

    cc  -I/usr/local/natinst/nidaqmxbase/include -I/usr/local/natinst/LabVIEW-2009/cintools build/square.so  test.c   -o test/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(float&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(double&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(double&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_ostream >& std::basic_ostream >::_M_insert(double)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(float&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_ostream >& std::basic_ostream >::_M_insert(double)@GLIBCXX_3.4.9'collect2: ld returned 1 exit statusmake: *** [test] Error 1
    

    Running ldd reveals that liblvrtdark.so.9.0 is used for the execution of labview.

    In order to investigate on what could be the cause of the problem, I have compiled the nidaqmx basic examples, and I don't have an error. Current running ldd as reveals that he uses liblvrtdark.so.8.2 for the view of laboratory, time of execution.

    My suspicion is that some components of labview are being compiled with gcc 3.4 while others are being compiled with gcc 4.1 (which is the default compiler in RHEL 5).

    Any ideas how I could fix the build errors?

    Thanks in advance for your suggestions.

    PS.

    I enclose a tar file with the source files and here are the details of the ldd:

    ldd build/square.so         linux-gate.so.1 =>  (0x008de000)        liblvrtdark.so.9.0 => /usr/local/lib/liblvrtdark.so.9.0 (0x00b9c000)        libc.so.6 => /lib/libc.so.6 (0x00110000)        libstdc++.so.6 => /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 (0x009a7000)        libm.so.6 => /lib/libm.so.6 (0x00756000)        libdl.so.2 => /lib/libdl.so.2 (0x00256000)        libpthread.so.0 => /lib/libpthread.so.0 (0x0025a000)        /lib/ld-linux.so.2 (0x00b80000)        libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x00272000)
    
    ldd /usr/local/natinst/nidaqmxbase/lib/libnidaqmxbase.so.3.3.0         linux-gate.so.1 =>  (0x00e50000)        libnidaqmxbaselv.so => /usr/local/lib/libnidaqmxbaselv.so (0x00248000)        libc.so.6 => /lib/libc.so.6 (0x00689000)        /lib/ld-linux.so.2 (0x00b80000)        liblvrtdark.so.8.2 => /usr/local/lib/liblvrtdark.so.8.2 (0x00e51000)        libdl.so.2 => /lib/libdl.so.2 (0x00813000)        libpthread.so.0 => /lib/libpthread.so.0 (0x001b0000)        libstdc++.so.5 => /usr/lib/libstdc++.so.5 (0x009c7000)        libm.so.6 => /lib/libm.so.6 (0x00b0a000)        libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x0050c000)
    

    Hi mimi,

    I'm happy to report that I managed to get the code to work. I have included some of the steps I experienced the problem in case it might help improve the documentation or future generations.

    In response to your question about the "error 1" reported by do, it's just an indication that detected a compiler error (it probably resembles the return code of the compiler).

    The errors ' undefined reference... @GLIBCXX_3.4.9 "have been narrowed down. The generated labview shared library, the square.so, links to /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 which is a symlink to usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6.0.9. I decided to compare this version of libstdc ++ that included with RHEL:

    strings /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 | grep GLIBCXXGLIBCXX_3.4GLIBCXX_3.4.1GLIBCXX_3.4.2GLIBCXX_3.4.3GLIBCXX_3.4.4GLIBCXX_3.4.5GLIBCXX_3.4.6GLIBCXX_3.4.7GLIBCXX_3.4.8GLIBCXX_3.4.9GLIBCXX_FORCE_NEW
    
    strings /usr/lib/libstdc++.so.6 | grep GLIBCXXGLIBCXX_3.4GLIBCXX_3.4.1GLIBCXX_3.4.2GLIBCXX_3.4.3GLIBCXX_3.4.4GLIBCXX_3.4.5GLIBCXX_3.4.6GLIBCXX_3.4.7GLIBCXX_3.4.8GLIBCXX_FORCE_NEW
    

    So libstdc ++ RedHat does not include a string for GLIBCXX_3.4.9.

    With this in mind, I was able to get my test application to compile using the version of LabVIEW libstdc ++ using the following makefile:

    .PHONY: all cleanCPPFLAGS=-I/usr/local/natinst/nidaqmxbase/include -I/usr/local/natinst/LabVIEW-2009/cintoolsLDFLAGS=build/square.so \        /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 \        -Wl,--rpath -Wl,/usr/local/lib/LabVIEW-2009/patchlib/
    
    all: test
    
    clean:        rm -f test *.o
    

    When you try to run the application, I got the following error:

    ./test: error while loading shared libraries: /usr/local/lib/liblvrtdark.so.9.0: cannot restore segment prot after reloc: Permission denied
    

    But apparently, it's because of SELinux prohibiting the use of libraries shared with moving text.
    This can be disabled by running /usr/sbin/setenforce 0 as root.

    The test application now works!

    See you soon,.

    RW

  • Can what cards I use to develop communication SPI with Labview?

    First of all, I'm an intern is currently working on a project that involves communication with an SPI interface. I have absolutely no experience with SPI, but I finally decided to try. I work for about 6 months with labview and understand the function of basis of a large number of its resources.

    The problem:

    We want to connect Labview to an evaluation Committee that is connected to the PC via USB (but it can also be adapted to connect through SPI). The evaluation board mainly reads and writes if sign up for issuers that are connected to it by a Module assessment. The program which is already which is the Studio of SmartRF (that works via USB), but as we want to link all the functions in Labview we redevelop a platform to do so. If shortly, we want to make a Studio of SmartRF version in Labview. We want to be able to get all the information that makes the program and others... and all this is possible through SPI.

    Here is a link in case you are interested what is SmartRF Studio: SmartRF Studio link

    My question is which card do you recommend for what we are trying to accomplish? We are looking for something not very expensive but who fail to meet our requirements.

    I think of the NI USB 8451, but please make suggestions.

    Thanks a lot in advance and please stay tuned to my many questions coming about how to accomplish this enormous task with no knowledge whatsoever of SPI or how to mix with Labview only one student. I am reading as much as I can find, so all the links will also be very much appreciated. If anyone has any experience with NI USB 8451 with Labview be kind enough to guide me

    Sincerely,

    Gisela

    If you have very little experience with LabVIEW and SPI, the 8451 is a good choice. It's expensive, but it's really easy to use and configure.

    The Aardvark is also a good choice. There pilots LabVIEW is also easy to use in LabVIEW. The disadvantages is that it doesn't have a lot outside of simply making SPI or I2C - in other words, it doesn't have a lot of GPIO. This can be important when control of multiple SPI devices, because it requires to select them lines individual slave.

    Dinah is really more than a product of laboratory, or something that is meant to be placed inside a camera. It is expensive, compared to the other two, but it doesn't have native drivers in LabVIEW. On the contrary, it comes with a DLL you can call from LabVIEW. I wrote a set of LabVIEW drivers for it, but I can't distribute.

    There are other products on the market, which some will resemble a device series to your computer. For example, you would use VISA to communicate with the SPI controller, and it would appropriate communication of SPI.

    Among the three mentioned here, I would suggest that you go with the neither of the Aardvark, one.

  • How can I change video images with labview

    Hello, I have video about 5 minutes and I want to change it in photos with labview, can you please help me?

    Assistant of vision is the Vision Development Module and represents a Configuration environment including the generation of Code for the Industrial Applications of Vision.

    Separeting Images in AVI files will take a few screws low level. However there are many examples to view shipped with LabVIEW.

    Christian

Maybe you are looking for

  • Something has changed with Firefox in the last 3 weeks?

    About 3-4 weeks ago that I started having bad to stay connected to my account I have with a site that offers paid web TV. I've never had a problem with staying connected. I log into my account, I choose a programme I want to watch, say a 10 minutes n

  • Using a Skype number for working

    HelloI live in Italy and I work for a Dutch company. I'll have to call a large number of Dutch customers and they should be able to remember. It's very expensive to call with my phone to other countries, so I was thinking of using Skype for this. Of

  • Used to scan HP Photosmart connected to a MAC.

    Series of HP Photosmart C4400 1 both iMac and MacBook Pro under OS X 10.6.8 Habit of scanning, scanner section does not register in the system, preferences/print & fax

  • HP Mini 210-2070NR does not illuminate

    The computer was running and makes a funny noise - perhaps the disk is going bad? I watch yet, but when I looked, it was off and the led 'works '. has been turned off, and the computer does not illuminate. How can I determine if the drive is bad and

  • Change the Ram in a Lenovo R60

    Hello How can I change RAM in my Lenovo? I'm not sure of the location. Help, please! Bent (Denmark)